EverFocusメーカーED335の使用説明書/サービス説明書
ページ先へ移動 of 18
1/3” CCD Indoo r 3-Axis Dual V oltage T rue Day/Night IR Dome Came ra Operation Instructions Model No. ED335 Please read this manual first for correct installation and operation. This manual should be re t ained for fu tur e reference. The information in this manual wa s current when published.
1 PRODUCT OVER VIEW ED335 is a new design IR Dome camera from Everfo c us. It incorporates breakthrough DSP technolog y to provide brilliant color images in well lit environmen ts.
2 Power supply pigtail Video test cable Accessory pack #2 containing t wo flush mounting clips DIMENSIONS.
3 SPECIFICA TIONS Pickup Device 1/3” SONY Super HAD CCD Video Format NTSC or P AL Scanning System NTSC: 525 TV lines, 60 fields/sec; P AL: 625 TV lines, 50 fields/sec. Picture Element 768 x 494 (NTSC); 752 x 582 (P AL) Horizontal Resolution 520 TV Lines Sensitivity 0 Lux (IR LED on) 0.
4 MAJOR P AR TS: NAMES AND FUNCTIONS Front View Side View 2. IR LEDs 4. Light sensor 1. Outer Base 6. Focus Adjust 8. Video Output 9. Power Input 3. Lens 5.
5 Back V iew 1. Base The camera unit sets in the dome base, when it is s hipp ed from the factory . This base is used for surface mounting, and is discarded fo r fl ush mounting. 2. IR LEDs 3. Lens The included vari-focal, DC iris lens allows manual adjustment of the field of view (zoom & focus).
6 7. Zoom Ring T o adjust the viewing angle, loosen t he zoom ri ng knob. T urn the ring toward <W> to Zoom out or <T> to Zoom in as necessary , and re-tighten when the a djustment is complete. 8. Video Output Please connect to the BNC connecto r of the cable from the DVR or monitor .
7 3-AXIS GIMBAL BRAC KET The 3-axis gimbal enables installers to easily moun t the camera on a wall or ceiling and then using the built in tilt and dual axis 180° twist, to adjust the viewing a n gle to the desired direction.
8 INST A LLA T I ON An ED335 camera may be mount ed in two ways: surface mount and flush mount. Select the one that meets your needs. Installation - Surface Mount 1. Paste the drilling template on the ceiling or wall. P le ase refer to the drilling template belo w .
9 4. Remove dome cover (4 captive hex head screws); re m ove inner base from outer base (4 Phillips head screws – retain these for later re-assembly). 5. Pull the cables to be connected to power and video ca bles into the outer base from the ceiling or wa ll.
10 7. Attach power and video cables from source to c ables from camera and push exce s s wire back into hole. 8. Insert inner base into outer base and se c ure using the 4 Phillips removed in the earlier step . Preposition camera so it is facing approximately in the desired direction.
11 10. Once the camera view is as desired, attach the cover to oute r base with the captive hex head screws..
12 Installation - Flush Mount 1. Paste the drilling template on the ceiling or wall. P le ase refer to the drilling template belo w . 2. Use the appropriate tool to drill the OUTER holes; carefully cut a lo ng the dashed circle to create a clearance hole for the inner base unit.
13 5. Unscrew the 4 Philips screws (retain f or future use) to detach the inner base from the o uter base. Set aside the outer base. 6. Screw the 2 spring tabs in the orientation shown t o the slots at both sides of the inner base using the 4 Philips head screws provided.
14 7. Atta c h power and video cables from source to cab les from camera and push excess wire ba ck i nto hole. Fold the spring tabs up. 8. Preposition camera so it is facing approximate ly in the desired direction. 9. Push the entire inner base into ceiling while holding the spring tabs with both hands.
15 10. The spring tabs will open automatically to support the camera against the ceiling. 1 1. Use the long Phillips pan head screws (x4) provided to screw the base to the ceiling.
16 12. Attach video test cable to test point on rear of camera modu le . Aim and focus the ca mera. Remove test cable. 13. Screw the cover back to the base with capt ive hex head screws.
17 Headquarters Of fice 12F, No.79 Sec. 1 Shin-Tai W u Road, Hsi-Chi, Taipei , Taiwan Tel: +886-2-26 982334 Fax: +886-2-2 6982380 Beijing office Room 609,T echnology Trade Bui lding.
デバイスEverFocus ED335の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
EverFocus ED335をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはEverFocus ED335の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。EverFocus ED335の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。EverFocus ED335で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
EverFocus ED335を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はEverFocus ED335の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、EverFocus ED335に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちEverFocus ED335デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。