Allied Telesisメーカー613-001480の使用説明書/サービス説明書
ページ先へ移動 of 16
PN 613-001480 Rev A 1 A T -S94 V ersion 3.0.0.41 A T -8000S Switch Softwar e Release Notes Please read this document before you be gin to use the management softwa re. Caution Failure to upgrade the bootloader before the release soft ware can result in a switch that will not boot.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 2 Allied Telesis, Inc. Supported Platforms The following platforms are included in the AT -8000S family of devices: A T -8000S/16 – 16 FE ports with 1 combo 10/10 0/1000 SFP Port.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 3 Allied Telesis, Inc. What’s New in Version 3.0.0.41 New Software Features None Resolved Issues In some cases where more than one switch has the same STP Bridge Priority value in a network, the swit ch with the higher MAC address wo uld be elected as the STP root bridge.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 4 Allied Telesis, Inc. Port lock: Port security mechanism is not trigg ered for MAC violation if MAC is learned on another locked port as a secured MAC ad dress. Recommended User W ork Around: No work around Mac-group mapping and 802.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 5 Allied Telesis, Inc. Version 3.0.0.41 Upgrade Process You must have the correct software and bootloader installed o n your switch before be ginning the upgrade process to Version 3.0.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 6 Allied Telesis, Inc. 6. Assuming your switch is running the correct bootloa der, you have the correct password to extract the ats94-30041.ros software upgrade file and you know that your current bo otloader is compatible with the Version 3.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 7 Allied Telesis, Inc. 10. Before rebooting the stand alone switch or stack, you mu st change the active image, including each slave switch in the stack. To c heck the active image for each switch use the following command.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 8 Allied Telesis, Inc. 5. Select number one by pressing the ‘1’ key. The switch will respond with the following message : Begin the transmission of a previous version. Downloading code using XMODEM.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 9 Allied Telesis, Inc. Version 3.0.0.33 When the master was lost (powered do wn) the SFP port(s) on backup change d to DOWN – link changed to half duplex and remained down. This issue has been resolved.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 10 Allied Telesis, Inc. The following is a new CLI command introduced in V ersion 3.0.0.40: Version 3.0.0.38 No new features were introduced in this release. Version 3.0.0.35 No new features were introduced in this release.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 11 Allied Telesis, Inc. The following 802.1x feature enhance ments will be su pported: — Guest VLAN - This feat ure allows network adm inistrators to giv e some limited access to the network to unauthorized port s.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 12 Allied Telesis, Inc. Upgrade Procedure fr om Version 1.0.0.25 All software released after version 1 .0.0.25 requires additional FLASH sectors beyond the current amount of FLASH sectors currently allocated for the image.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 13 Allied Telesis, Inc. 2. Download the ats94-Interim image drop to the device via TFTP by using one of the followin g commands depending on your configuration: Note You must substitute the IP address of your local TFTP server.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 14 Allied Telesis, Inc. 7. Before rebooting the stand alone switch or stack, you mu st change the active image, including each slave switch in the stack. To c heck the active image for each switch use the following command.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 15 Allied Telesis, Inc. 14. Before rebooting the stand alone switch or stack, you mu st change the active image, including each slave switch in the stack. To c heck the active image for each switch use the following command.
AT-S94 Version 3.0.0.41 Software Release Notes PN 613-001480 Rev A 16 Allied Telesis, Inc. Contacting Allied Telesis This section provides Allied Teles is contact information for technical support as well as sales and corporate information. Online Support You can request technical support online by accessing the Allied Tel esis Knowledge Base: www.
デバイスAllied Telesis 613-001480の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Allied Telesis 613-001480をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAllied Telesis 613-001480の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Allied Telesis 613-001480の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Allied Telesis 613-001480で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Allied Telesis 613-001480を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAllied Telesis 613-001480の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Allied Telesis 613-001480に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAllied Telesis 613-001480デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。