Exmarkメーカー000 & Higherの使用説明書/サービス説明書
ページ先へ移動 of 56
LAZER Z ® MODELS For Serial Nos. 790,000 & Higher Part No. 4500-471 Rev . A.
W ARNING CALIFORNIA Proposition 65 W ar ning The engine exhaust from this product contains chemicals known to the State of Califor nia to cause cancer , birth defects, or other reproductiv e har m.
Introduction CONGRATULATIONS on the purchase of y our Exmark Mow er . T his product has been carefully designed and manufactured to giv e you a maximum amount of dependability and years of trouble-free operation. This manual contains operating, maintenance, adjustment, and safety instr uctions for your Exmark mow er .
Contents Introduction .. . . .. . . .. . . .. . . .. . . .. . . .. . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. 3 Safety .. . . .. . . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . .. . . . .. . . .. . . .. . . .. . . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1.
Safety DANGER In certain conditions gasoline is extremely ammable and v apors are explosi v e. A re or explosion from gasoline can bur n y ou, others, and cause proper ty damage. • Fill the fuel tank outdoors in an open area, when the engine is cold.
Safety CAUTION Fuel tank v ent is located inside the roll bar tube. Removing or modifying the roll bar could result in fuel leakage and violate emissions regulations. • Do Not remov e roll bar . • Do Not w eld, drill, or modify roll bar in any w ay .
Safety • Be a ware of the mo wer discharge path and direct discharge a way from others . • Do Not operate the mow er under the inuence of alcohol or dr ugs .
Safety W ARNING There is no rollov er protection when the roll bar is down. Wheels dropping o ver edges, ditches, steep banks, or w ater can cause rollov er s, which may result in serious injur y , death or drowning . • Keep the roll bar in the raised and lock ed position and use seat belt.
Safety Safety and Instructional Decals • Keep all safety signs legible . R emov e all grease, dirt and debris from safety signs and instructional labels . • R eplace all w or n, damaged, or missing safety signs . • When replacement components are installed, be sure that cur rent safety signs are afx ed to the replaced components .
Safety 107-2102 107-21 12 109-3148 109-7232 1. Fast 3. Neutral 2. Slow 4. Reverse 109-7330 109-7929 1 1.
Safety 109-8483 1. Throttle–fast 3. Choke–on 2. Throttle–slow 4. Choke–off 109-9361 Deck Drive Belt Routing 109-9477 1 16-0090 1 16-0157 1. See Operator’s manual 1 16-0165 1 16-0205 12.
Safety 1 16-021 1 1 16-0752 1. Latch 2. Unlatch Message Display 1. Fuel 6. Hour meter 2. Empty 7. PTO 3. Half 8. Parking brake 4. Full 9. Neutral 5. Battery 10.
Specications Specications Model Numbers Serial Nos: 790,000 and Higher LZZ23K C486; LZZ23KA526; LZZ23K C526; LZZ27K C526; LZZ27K C606; LZZ29KA606; LZZ34KA606; LZZ34KA726 Systems Engine • Engin.
Specications • Deck Height Adjustment Lever: Sets cutting height to desired position. • Deck Lift P edal: F oot pedal that lifts dec k. • T ransport Lock: – Latching position: A utomatically latc hes at the transport position. – Unlatching position: Deck does not latch at the transport position.
Specications Cutting Deck • Cutting Width: – 48 inc h Dec k: (121.9 cm) – 52 inc h Dec k: (132.1 cm) – 60 inc h Dec k: (152.4 cm) – 72 inc h Dec k: (182.9 cm) • Discharge: Side • Blade Size: (3 ea.) – 48 inch Deck: 16.25 inc hes (41.
Specications T read W idth: (Center to Center of Tires, W idthwise) 48 inch Deck 52 inch Deck Driv e Wheels 36.2 inches (91.9 cm) 36.2 inc hes (91.9 cm) Caster Wheels 32.8 inches (83.3 cm) 32.8 inches (83.3 cm) 60 inch Deck 72 inch Deck Driv e Wheels 41.
Product Overview *60 inc h units whic h already hav e an under toe board mount w eight as standard requires 116-1238 front toe board top mount kit instead of 116-1173.
Operation Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Controls Motion Control Levers The motion control lev ers located on each side of the console control the forw ard and rev erse motion of the machine .
Operation Note: The LCD indicator appears in the message display on the RH console when the park brake is engag ed (see Figure 9). Pull the lev er up and rearward to engag e the brak e . Depress the release button and push downw ard to disengag e the brak e.
Operation Fuel Shut-Off V alve Located behind and below the seat. The fuel shut-off valv e is used to shut off the fuel when the machine will not be used for a few da ys , during transport to and from the jobsite, and when parked inside a building . Align v alve handle with the fuel line to open.
Operation Deck Lift Pedal Located at the right front corner of the oor pan. Push the pedal forward with y our foot to raise the cutting dec k. Allow the pedal to mo ve rearward to low er the cutting deck to the cut height that has been set. T ransport Lock Located on the height of cut adjustment plates to the right of the parking brake .
Operation the roll bar ma y need to be pushed forward or pulled rearward to get both knobs fully engaged (see Figure 13). Figure 13 1. Engaged 2. Partially engaged — Do Not operate with ROPS in this condition. Important: Alw ays use the seat belt with the roll bar in the operate (raised) position.
Operation Stopping the Engine 1. Bring the unit to a full stop . 2. Disengag e the PTO . 3. Mov e the motion control lev ers out to the neutral lock position. 4. Engag e the parking brake . 5. Place the throttle midw ay betw een the “SLO W” and “F AST” positions .
Operation Figure 15 1. Front of Unit 3. Neutral 2. Forward 4. Reverse Driving in Rev erse 1. Mov e the motion control levers inward to the neutral operate position. 2. T o mov e rearward in a straight line , mov e both levers rearward with equal pressure.
Operation Figure 17 For cutting heights above 3.5 inches (90 mm) use the bottom hole. The rollers will still be effective against scalping. 1. Anti-scalp roller mounting bracket 2. Cutting height F or Maximum Deck Flotation, place the rollers one hole position low er .
Operation W ARNING Loading a unit on a trailer or tr uck increases the possibility of backw ard tip-o ver . Backw ard tip-o ver could cause serious injur y or death. • Use extreme caution when operating a unit on a ramp . • Use only a single, full width ramp; Do Not use indi vidual ramps for each side of the unit.
Maintenance Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Maintenance Ser vice Inter v al Maintenance Procedure Every 500 hours • Change the hy draulic lter and uid. • Chec k the wheel hub slotted nut torque specications . • Chec k the wheel lug nuts . • Chec k the park brake adjustment.
Maintenance Check Mower Blades Service Interval: Before each use or daily 1. Stop engine, w ait for all moving parts to stop , and remov e key . Engag e parking brake . 2. Lift dec k and secure in raised position as stated in the Clean Grass Build-Up Under Deck section.
Maintenance second has elapsed (seat has time dela y kill switc h to prev ent cut-outs on rough terrain). R un engine at one-third throttle , engage PT O and raise of f of seat (but do not get off of machine) engine must initiate shutdown after one second has elapsed if the handles are in.
Maintenance 4. Check the condition of the inner element. R eplace whenever it appears dirty , typically ev er y other time the paper element is replaced. Clean the base around the inner element before remo ving, so dirt does not get into the engine . 5.
Maintenance Check Condition Of Belts Service Interval: Every 50 hours 1. Stop engine, w ait for all moving parts to stop , and remov e key . Engag e parking brake . 2. R emov e left and right belt shields on dec k and lift up oor pan to inspect dec k driv e belt.
Maintenance 9. Insert the assembled nut and axle into the wheel on the side of the wheel with the new seal and bearing . 10. With the open end of the wheel facing up , ll the area inside the wheel around the axle full of NGLI grade #1 m ulti-purpose grease.
Maintenance 7. Before installing the new lters , apply a thin coat of Exmark Premium Hydro oil on the surface of the tw o rubber seals . 8. Install the new lters and torque to 14 ft-lb (19 N-m). 9. Fill the hy draulic system as stated in Check Hydraulic Oil Lev el section.
Maintenance 3. If any breaks in the screen or w elds are obser v ed, replace arrester . 4. If plug ging of the screen is observed, remo ve ar rester and shak e loose particles out of the ar rester and clean screen with a wire brush (soak in solvent if necessar y).
Maintenance Figure 25 1. Foot lever 3. T ransport lock 2. Cut of height pin 6. Insert the height adjustment pin into the 3 inc h (7.6 cm) cutting height location. 7. R elease the transport lock and allow the dec k to low er to the cutting height. 8. Raise the disc harge deector .
Maintenance Figure 28 1. Single point height adjustment bolt 2. Front height-of-cut plate mounting bolt 3. Rear height-of-cut plate mounting bolt 15. T o adjust the single point system, rst loosen the front and rear height-of-cut plate mounting bolts .
Maintenance 7. Raise the front of the mac hine and slide the deck left or right to remov e. 8. Low er the front of the mac hine. Pump Drive Belt T ension Self-tensioning - No adjustment necessary . Deck Belt T ension Self-tensioning - No adjustment necessary .
Maintenance 16. Install the rear tires and torque lug nuts to 90-95 ft-lb (122-129 N-m). 17. R emov e jac k stands . Electric Clutch Adjustment No adjustment necessar y . Motion Control Linkage Adjustment Located on either side of the fuel tank, belo w the seat are the pump control linkages .
Maintenance Figure 32 RH Motion Control Shown 1. T orque nyloc nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of nyloc nut after torque. A T -40 T orx bit will be necessary to hold the stud from turning. 2. Most resistance (rmest feel) 3.
Maintenance 2. Slide the co ver plate backw ard or forward to adjust the trav el of the lever and tighten the screws . 3. Driv e the machine and chec k the full forw ard tracking . 4. R epeat steps 1 through 3 until desired trac king is obtained. Figure 35 RH Motion Control Shown 1.
Maintenance Cleaning Clean Engine and Exhaust System Area Service Interval: Before each use or daily (May be required more often in dry or dirty conditions.) CAUTION Excessi ve de bris around engine cooling air intake and exhaust system area can cause engine, exhaust area, and h y draulic system to o verheat which can create a re hazard.
Maintenance CAUTION Raising the mo wer deck for ser vice or maintenance relying solely on mechanical or hy draulic jacks could be dangerous. The mechanical or h ydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injur y .
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , do not o verlook the simple causes . F or example: starting problems could be caused by an empty fuel tank.
T roubleshooting Problem Possible Cause Cor rectiv e Action 1. Engine load is ex cessiv e 1. R educe the ground speed. 2. Air cleaner is dirty . 2. Clean or re place the air cleaner element. 3. Oil lev el in the crankcase is low . 3. Add oil to the crankcase .
Schematics Schematics Electrical Diagram G008587 PTO SWITCH SEA T SWITCH IGNITION SWITCH FUSE BLOCK REGULA TOR GROUND PTO CLUTCH ST ART RELA Y LH NEUTRAL SWITCH RH NEUTRAL SWITCH BRAKE SWITCH ST ART RED HOUR METER/MODULE L T.
Schematics Electrical Logic Schematic BN BN BU BK Y W T PK BN PK OR GN S R PK PK PK L TGR GY GY PK V BN V OR GN OR R PK R BK GND PK BK BN BN BK PK BK GND 15A F4 GY R I B A W V BU V V BK + S - FUEL SEN.
Schematics Hydraulic Diagram 49.
General Warranty Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions.
Notes: 51.
Notes: 52.
Service Record Date: Description of Work Done: Service Done By: 53.
54.
55.
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
デバイスExmark 000 & Higherの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Exmark 000 & Higherをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはExmark 000 & Higherの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Exmark 000 & Higherの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Exmark 000 & Higherで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Exmark 000 & Higherを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はExmark 000 & Higherの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Exmark 000 & Higherに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちExmark 000 & Higherデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
