Exmarkメーカー4500-435の使用説明書/サービス説明書
ページ先へ移動 of 20
ST ANDON For Serial Nos. 790,000 & Higher Part No. 4500-435 Rev . A.
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y .
Introduction CONGRATULATIONS on the purchase of your Exmark StandOn. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This manual contains assembly , operating, maintenance, adjustment, and safety instr uctions for your StandOn.
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1.
Safety DANGER Operating on wet grass or steep slopes can cause sliding and loss of control. Loss of control and/or loss of operator’s footing could result in a fall with an ar m or leg getting under the mow er or engine deck which may result in serious injur y , death or drowning .
Safety Safety and Instructional Decals • Keep all safety signs legible . Remo ve all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components .
Specications Specications Model Numbers Serial Nos: 790,000 and Higher ST ANDON Dimensions Length Width Height W eight 35.4 inches (89.9 cm) 18.5 inches (47.0 cm) 14.9 inches (37.9 cm) 50 lb (23kg) T ire T read Size Semi-Pneumatic Tire Smooth 11 x 4.
Setup Setup Assembly Diagram Item Quantity Description 1 8 Nut, Nyloc 3/8-16 Flg 2 2 Plate, Back-Up 3 2 Plate, Adapter 4 8 Screw , HH 3/8-16 x 1 1/4 5 1 Asm, F rame Pull W/Decals 6 1 Asm, Pull Arm W/B.
Setup Installing the StandOn Rider to Mower Mounting the Pull Frame 1. Locate the pull frame and tw o adapter plates . Install the pull frame to the adapter plates using four 3/8-16 x 1 1/4 inc h hex capscrews and four 3/8-16 inch nyloc nuts as shown in Figure 4.
Setup Figure 7 1. Replacement decals e. Align the pull frame and adapter plate assembly to the rear surface of the engine deck. Measure the distance from the bottom of the pull frame to the g round. Choose the mount holes that will attain a distance appro ximately 8 inc hes (20 cm).
Setup Figure 10 1. Pull arm assembly 3. Pull frame 2. Quick connect pins 2. R emov e the 3/8-16 x 4 3/4 inc h hex capscrew . spring disc w asher , and 3/8-16 inc h hex ange side loc k n ut from the piv ot hub . 3. Locate the sulky frame assembly and align with the pull ar m assembly .
Operation Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start 1. Make sure y ou understand the controls , their locations , their functions , and their safety requirements . 2. Practice operating the machine without the StandOn until familiar with the controls .
Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Lubricate Caster Wheel Hubs Service Interval: Y early 1. Stop engine , w ait for all mo ving parts to stop , and remov e key . Engag e parking brake . Figure 13 1. Seal guard 2. Spacer nut with wrench ats 2. R emov e the caster wheel from the sulky frame .
Maintenance Adjustments Adapter Plate and T ire Adjustment Important: F or optimal perfor mance, the StandOn pull ar m top surface should be horizontal to the ground surface. T o obtain a horizontal pull ar m, the adapter plates and the platfor m wheel can be repositioned (see Figure 14).
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Ex mark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we.
Service Record Date: Description of Work Done: Service Done By: 18.
19.
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
デバイスExmark 4500-435の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Exmark 4500-435をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはExmark 4500-435の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Exmark 4500-435の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Exmark 4500-435で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Exmark 4500-435を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はExmark 4500-435の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Exmark 4500-435に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちExmark 4500-435デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。