ExmarkメーカーM217b, M217bspの使用説明書/サービス説明書
ページ先へ移動 of 36
Part NO. 850553 3321–185 METRO 21 Operator ’ s Manual.
ii Exmark Manufacturing Company – 1998 Printed in USA All Rights Reserved W ARNING F AILURE TO FOLLOW CAUTIOUS OPERA TING PRACTICES CAN RESUL T IN SERIOUS OPERA TOR INJUR Y . 1. Keep all shields, guards and safety devices (especially grass discharge system) in place and in proper working condition.
iii EXMARK P AR TS PLUS PROGRAM EFFECTIVE DA TE: September 1,1995 Program & 8.41 7,!1* $%!+%1 $.%2 -.3 (!5% 3(% 7,!1* /!13 )- 23.#* 7,!1* 6)++ '%3 3(% /!132 3. 3(% $%!+%1 3(% -%73 "42)-%22 $!8 .
iv CONGRA TULA TIONS on the purchase of your Exmark Mower . This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble-free operation. Operator ’ s Manual This manual contains assembly , operating, maintenance, adjustment and safety instructions for your Exmark mower .
1 Contents Page Specifications 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safe Operating Practices 2 . . . . . . . . . . . . . . General Operation 2 . . . . . . . .
2 DANGER, W ARNING and CAUTION are signal words used to identify the level of hazard. However , regardless of the hazard, be extremely careful. DANGER signals an extreme hazard that will cause serious injury or death if the recommended precautions are not followed.
3 D. Do not smoke while refueling. 6. Keep all guards, shields, grass catcher , discharge tunnel plug, optional discharge chute and safety devices in place. Repair or replace damaged parts, including decals. Check all safety devices before each use. 7.
4 Maintenance And Storage 1. Perform only those maintenance instructions described in this manual. If major repairs are ever needed or if assistance is desired, contact your local Authorized Exmark Service Dealer . 2. Before mower is cleaned, inspected, serviced, or adjusted, stop engine and disconnect wire from spark plug.
5 Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger . Replace any decal that is damaged or lost. ON MOWER HOUSING (Part No. 213239) Hand-push model only ON BEL T COVER (Part No.
6 Assembly Install Handle 1. Mount handle to outside of mower housing, using bottom hole, with (2) 5/16–18 x 1–1/4” lg. capscrews, washers, and thin nylon insert locknuts (Fig. 2). 2. Secure handle latches to handle with (2) 5/16–18 x 1–1/2” lg.
7 low , add only enough oil to raise level to FULL mark on dipstick. DO NOT FILL ABOVE FULL MARK BECAUSE ENGINE COULD BE DAMAGED WHEN ST AR TED. POUR OIL SLOWL Y . 4. Insert dipstick into filler neck and rotate cap clockwise 1/4 turn to lock (Fig. 8).
8 grass must be cut, use highest height-of-cut setting for first mowing. Then recut the grass at a more normal setting. If too long of grass is cut, mower may plug and cause engine to stall. 2. SHARP BLADE—Begin each cutting season with a sharp blade.
9 POTENTIAL HAZARD • Grass clippings and other objects can be thrown fr om an open discharge tunnel. WHA T CAN HAPPEN • Objects thrown with enough for ce could cause serious personal injury or death to operator or bystander .
10 setting. Assure pin on adjusting lever engages notch in mower housing wear plate. Adjust all wheels to the same setting. POTENTIAL HAZARD • Adjusting height-of-cut levers could bring hands into contact with moving blade. WHA T CAN HAPPEN • Contact with blade could cause serious personal injury .
11 Cutting Leaves • When cutting is complete, always be sure that 50% of the lawn shows through the cut leaf cover . This may require one or more passes over the leaves. • For light leaf coverage, position all wheels at the same height-of-cut setting.
12 IMPOR T ANT : Replace a cracked, fouled, or dirty spark plug. Do not sand blast, scrape, or clean electrodes because engine damage could result fr om grit entering cylinder . 3. Set air gap at 0.020” (0.50 mm) (Fig. 17). Install correctly gapped spark plug and gasket seal.
13 3. CHECK ADJUSTMENT—Slowly pull mower backward while control bar is gradually moved toward handle. Adjustment is correct when rear wheels stop turning and control bar is about one inch from handle (Fig. 21). Inspecting, Removing, Sharpening Blade Always mow with a sharp blade.
14 Lubrication After every 25 operating hours or when season ends, pivot arms must be lubricated. 1. Move rear wheel height–of–cut levers to center setting. W ipe grease fittings with clean rag (Fig. 25). Install grease gun onto fitting and gently apply 2 or 3 pumps of #2 Multi–Purpose Lithium Base Grease.
15 5. Check alignment of all parts and tighten screws, alternating from side to side for a uniform fit, until wheel halves are drawn together . 6. Install two capscrews and locknuts, previously removed, in remaining holes in wheel halves and tighten. Remove two long screws or bolts and replace with two capscrews and locknuts.
16 Scraping Method If washing does not remove all debris from under deck, tip mower and scrape it clean. 1. Pull wire off spark plug. 2. Drain gasoline from fuel tank: refer to DRAINING GASOLINE section. 3. T ip mower on its right side. 4. Remove dirt and grass clippings with a hardwood scraper .
17 6. Check condition of blade: refer to INSPECTING, REMOVING, SHARPENING BLADE section. 7. T ighten all nuts, bolts, and screws. 8. Clean air cleaner: refer to SER VICING AIR CLEANER section. 9. Lubricate the pivot arms: refer to LUBRICA TION section.
18 W arranty Limited W arranty Exmark Commercial T urf Equipment Exmark Mfg. Co. Inc. (”Exmark”) warrants on the terms and conditions herein, that it will repair , replace or adjust any part manufactured by Exmark and found by Exmark(in the exercise of its reasonable discretion)to be defective in factory material or workmanship.
19 As a condition to this warranty , customer shall have read the operator ’ s manual and shall have returned to Exmark, within the prescribed time, the enclosed warranty registration card. The sole liability of Exmark with respect to this warranty shall be repair and replacement as set forth herein.
In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 20 273 Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.
In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 21 About your engine warranty: (see back cover for statement of LIMITED W ARRANTY). Briggs & Stratton welcomes warranty repair and apologizes to you for being inconvenienced.
In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. 22 BRIGGS & STRA TTON ENGINE OWNER W ARRANTY POLICY effe.
23 Figures m–3849 1 1. Model and serial number decal m–3850 1 2 3 4 1. Bag support rod 2. Cap locknut 3. Handle 4. Handle latch m–210 1 2 1. Rope guide 2. Starter rope 530 1 2 3 4 5 1. Plastic clips 2. Gas tank 3. Self-tapping screw 4. T ank bracket 5.
Figures 24 1 2 3 2045 1. Fuel line clamp 2. Elbow fitting 3. Fuel line m–262 2 1 1. Discharge door handle 2. Plug tilted clockwise m–275 1 1. Spring clip m–3845 1 2 3 4 1.
Figures 25 1992 1 2 3 1. Control bar 2. Throttle 3. Fingertip starter m–3662 1 2 1. Primer 2. Spark plug wire m–3849 1 1. Ground speed control m–261 1 3 2 1.
Figures 26 m–260 1 1. Pin locked in bag notch # 4 ! 4 # 4 ! 4 # 4 ! 4 976 1 225 English 1. Height-of-cut adjuster m–3664 1 2 3 4 1. Knob 2. Cover 3. Foam pre–cleaner 4.
Figures 27 m–3848 1 2 1. Oil fill tube 2. Oil filter m–3638 1 2 3 4 1. Cable clamp screw 2. Governor control lever 3.
Figures 28 m–3854 1 2 3 4 1. Blade 2. Bolt 3. Lockwasher 4. Accelerator 270 1 1 1 2 3 4 1. Sail 2. Flat part of blade 3. Wear 4. Slot formed 153 1 1.
Figures 29 224 1 2 1. Grease fitting 2. Belt cover 3. Cubierta de la correa 346 1 2 3 # / 16 ”- ! / 4 ” 1. Handle 2. Brake lever 3. Cable bracket 483 1 2 3 4 5 6 1. Handle 2. Brake lever 3. 3/16”-1/4” 4. Cable adjuster 5. Jam nut 6. Cable conduit 209 1 2 36 7 5 45 4 8 9 2 1.
Figures 30 1093 1. Right rear wheel m–3844 1 3 2 2 1. Hose clamp 2. Fuel line 3. Filter 2047 1. Side discharge chute 30 31 32.
Date Description Work Done Service Done By SERVICE RECORD.
3321–185 SEE EXMARK’S COMPLETE LINE OF PRODUCTS FOR TURF CARE LAZER Z LAZER Z HP EXPLORER TURF RANGER TURF TRACER HP VIKING HYDRO METRO METRO HP SELF STEERING SULKY GRASS CA TCHER MICRO MULCHING ACCESSOR Y EXMARK MFG. CO. INC INDUSTRIAL P ARK BOX 808 BEA TRICE NE.
デバイスExmark M217b, M217bspの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Exmark M217b, M217bspをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはExmark M217b, M217bspの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Exmark M217b, M217bspの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Exmark M217b, M217bspで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Exmark M217b, M217bspを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はExmark M217b, M217bspの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Exmark M217b, M217bspに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちExmark M217b, M217bspデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
