Extron electronicメーカーCTR 8の使用説明書/サービス説明書
ページ先へ移動 of 21
User Guide CTR 8 Switcher Accessories Eight Input Contact Closur e to RS-232 Contr ol Module 68-2524-01 Rev . A 12 13.
Safety Instructions Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock.
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interference when the equipment is operated in a commer cial environment.
Conventions Used in this Guide Notifications The following notifications are used in this guide: A TTENTION: Attention indicates a situation that may damage or destr oy the product or associated equipment. NOTE: A note draws attention to important information.
v CTR 8 • Contents Contents Introduction ............................................................ 1 About the CTR 8 ................................................ 1 Features ............................................................. 1 Panels and Cabling .
CTR 8 • Introduction 1 Intr oduction About the CTR 8 The Extron CTR 8 contr ol module provides contact closure input switching for most Extr on switchers with RS-232 capability . It allows simple push-buttons to remotely switch and mute audio and video sources.
CTR 8 • Panels and Cabling 2 Panels and Cabling This section covers the following: • Front Panel Featur es • Rear Panel Features and Cabling • Application Diagrams Fr ont Panel Featur es CTR 8 12V POWER IN POWER OUT RS-232 Tx 4 CG T+ V 3 CG T+ V 2 CG T+ V 1 CG T+ V 8 CG T+ V 7 CG T+ V 6 CG T+ V 5 CG T+ V G Tx Rx G 1.
CTR 8 • Panels and Cabling 3 a DC power input with loop through — Wire the external 12 VDC power supply as shown in figure 3 and connect it to the two-pole captive scr ew Power In connector . SECTION A– A Ridges Smooth Po wer Supply Output Cord A A 3/16” (5 mm) Max.
CTR 8 • Panels and Cabling 4 c Remote RS-232 port — Connect the serial port of a control computer to this female captive screw connector as shown below . CG T+ V Contact (C) Ground (G) T ally output (T) T ally voltage (+V) Tr ansmit (Tx) Receive (Rx) Ground (G) Tx Rx RS-232 G Tr ansmit (Tx) Ground (G) Tx COM G Figure 5.
CTR 8 • Panels and Cabling 5 Application with CCR 4BLB --A MAX POWER 12V 1 VIDE OR GB/R-Y,Y ,B-Y HDMI DSC 301 HD AUDIO 23 1 RS-232 Tx Rx G 23 INPUTS OUTPUT REMOTE PWR + G INPUTS 1 2 G 3 4 G OUTPUTS 1 2 G 3 4 G 12V POWER IN POWER OUT RS-232 Tx 4 CG T+ V 3 CG T+ V 2 CG T+ V 1 CG T+ V 8 CG T+ V 7 CG T+ V 6 CG T+ V 5 CG T+ V G Tx Rx G 1.
CTR 8 • Remote Communication and Control 6 Remote Communication and Contr ol This section covers the following: z Using Simple Instruction Set (SIS) Commands z Symbols Used in this Guide z Command a.
CTR 8 • Remote Communication and Control 7 Symbols Used in this Guide When programming in the field, certain characters ar e most conveniently represented by their hexadecimal rather than their ASCII values. The table below shows the hexadecimal equivalent of each ASCII character: ASCII to HEX Con version Ta bl e Space .
CTR 8 • Remote Communication and Control 8 Command and Response T able for SIS Commands Command ASCII Command (host to unit) Response (unit to host) Additional Description Select input X) ! Chn X)] .
CTR 8 • Remote Communication and Control 9 A/V mute modes are activated via SIS commands sent to the CTR 8. The COM port then sends SIS commands to the switcher . The table below shows the differ ent commands that the COM port sends for each A/V mute mode.
CTR 8 • Updating Firmware 10 Updating Firmwar e Updates to the CTR 8 firmware ar e released periodically on the Extron website. Y ou can find which version is currently loaded on your CTR 8 using SIS commands. Compar e this with the latest release on the Extr on website and decide whether to update your firmware.
CTR 8 • Updating Firmware 11 Downloading CTR 8 Firmwar e Figure 8. Firmware Link on the Download T ab T o obtain the latest firmware version for the CTR 8: 1. Visit the Extron website ( www .extron.com ), click the Download link at the top of the page.
CTR 8 • Updating Firmware 12 Figure 9. Opening Firmware Loader 4. In the Add Device dialog, select the device from the Device Names dr op-down list. 5.
CTR 8 • Updating Firmware 13 NOTES: • The original factory-installed firmware is permanently available on the CTR 8. If the attempted firmware upload fails for any r eason, the unit reverts to the factory version.
CTR 8 • Updating Firmware 14 Figure 12. Firmware Loader Scr een with the CTR 8 Added 11. If you want to remove a device, do the following: a. Click the names of the devices to be deleted, to highlight them. b. Select Edit > Remove Selected Device(s) fr om the toolbar .
CTR 8 • Mounting 15 Mounting T abletop Placement Attach the four provided rubber feet to the bottom of the unit and place it in any convenient location.
Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia +65.
デバイスExtron electronic CTR 8の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Extron electronic CTR 8をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはExtron electronic CTR 8の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Extron electronic CTR 8の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Extron electronic CTR 8で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Extron electronic CTR 8を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はExtron electronic CTR 8の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Extron electronic CTR 8に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちExtron electronic CTR 8デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。