Allied Telesisメーカーfast ethernet 10/100 hubsの使用説明書/サービス説明書
ページ先へ移動 of 32
USER’S GUIDE A T-FH81 2u A T-FH82 4u F ast Ethernet 10/100 Hubs PN 613-10 752- 00 Rev. B.
Copyright © 1998 Allied T elesyn International, Corp. 950 Kifer Road, Sunnyvale CA 94086 USA All rights reserved. No part o f this publication may be repr oduced w ithout prior w ritten permission from Allie d T elesyn Interna tional, Corp. Ethernet is a registered tr ademark of Xe rox Corporation.
iii T ab le of Contents AT-FH812u and AT-FH82 4u Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introducti on . . . . . . . . . . . . . . . . . . . . . . .
.
1 A T -FH812u and A T -FH824u Software Introduction The AT-F H812u and AT-FH824 u hub (and the c onnected stack) is m anaged throu gh a direct consol e or modem connection to the AT- FH801u network ma.
AT-FH812 u and AT-FH 824u S oftwar e 2 Requ ired Connections for System Configuration The hub i ncludes a me nu-dr iven con fig uratio n progr am. T he ASCI I inte rfac e to th is program is acce ssed by ma king a direc t connect io n t o the serial po rt on the Agent Module, or by a Telnet con nection to the hub o ver the n etwork.
AT-FH812 u and AT-FH8 24u U ser’s G uide 3 Making a Telnet Connection Before you access the hub via an in-b and Telnet connection or with a Web browser, you must first configure i t with a valid IP address, subnet mask and default g ateway, using an out-of-band connec tion or BootP pr otocol.
AT-FH812 u and AT-FH 824u S oftwar e 4 Con fi gur ing Your System with the Conso le Interfa ce Once a direc t conne ction t o the serial port or a Telnet conne ct ion is esta blis he d, the l ogin screen f or the on-b oard configurat ion program appears, as sho wn in Figur e 1.
AT-FH812 u and AT-FH8 24u U ser’s G uide 5 Using the System Configuration Prog ram The system configuration program let s you define system parameters; manage and control the hub, the connecte d stack and all its ports; and monitor network condit io ns.
AT-FH812 u and AT-FH 824u S oftwar e 6 T able 1 System Configuration Commands Menu Description System Information Provides system d escription, incl uding M IB identifier and o ther data . Restart Hub Resets management agen t for all hubs in stack or for selected hub.
AT-FH812 u and AT-FH8 24u U ser’s G uide 7 Displaying System Info rmati on Use the System In formation screen t o display descrip tive infor mation about the hub, or for quick sy stem identifi cation, as shown in F igure 3 and Table 2.
AT-FH812 u and AT-FH 824u S oftwar e 8 Resetting the System Use the Reset command under the Main Menu to re set the agent. Logging Off the System Use the Exit comm and unde r th e Main Menu to exi t the con f ig uration progra m and termin ate comm unicati on s wit h the swi tch for the cu rre nt session.
AT-FH812 u and AT-FH8 24u U ser’s G uide 9 Changing the Network Configuration Use the Ne tw or k Co nfiguration scr ee n to configu re the hub's Inter net Protocol (IP ) paramete rs, set th e bootup opti on, and defi ne the maximum number of T elnet sessions allo wed.
AT-FH812 u and AT-FH 824u S oftwar e 10 Assigning SNMP Parame ters U s e t he SNMP Conf ig uration scre e n to displ a y and mo dif y parame ters for t he Simple Network Managem ent Protocol (SNMP). The Ag ent Module mon itors the hardware status of the h ub (or connecte d stack), as well as th e traffic passing through th e port s.
AT-FH812 u and AT-FH8 24u U ser’s G uide 11 SNMP Communities SNMP Communities Community Name Access Statu s 1. public READ/WRITE Enabled 2. READ-ONLY Disabled 3. READ-ONLY Disabled 4. READ-ONLY Disabled 5. READ-ONLY Disabled <APPLY> <OK> <CANCEL> The name of this SNMP community entry.
AT-FH812 u and AT-FH 824u S oftwar e 12 IP Tr ap Ma nagers IP Trap Managers IP Address Community Name Status 1. 0.0.0.0 public Disabled 2. 0.0.0.0 public Disabled 3. 0.0.0.0 public Disabled 4. 0.0.0.0 public Disabled 5. 0.0.0.0 public Disabled 6. 0.0.
AT-FH812 u and AT-FH8 24u U ser’s G uide 13 Hub Configuration Use the Hub C onfiguration screen to c onfigure any hub in the stack. This men u is used to configure the selected hub , as well as the Agent Modul e.
AT-FH812 u and AT-FH 824u S oftwar e 14 Hub Configuration Menu -------------------------------------- ---------------------- Hub Configuration Hub ID : 1 H/W Ver : 1 Serial No : 11-00-00-00-10 -24 # o.
AT-FH812 u and AT-FH8 24u U ser’s G uide 15 T able 8 Hub Configuration P arameters Parameters Descrip tion Hub Hub ID Hub id entifier in stack. Serial No Serial nu mber of this hub. 10M Backplane Attaches/isolates hub's 1 0 Mbps repeater bus from the stack's data channel.
AT-FH812 u and AT-FH 824u S oftwar e 16 Configuring Port Parame ters Select Administr ative Status Co ntrol from the Port Co nfiguration sc reen to config ure any port on the hub . The follow ing menu show s the configur ation options. In addition to t he functional para meters listed in Figure 10, note th at you can also enable/disable an y port.
AT-FH812 u and AT-FH8 24u U ser’s G uide 17 T able 9 P or t Administration Status Control P arameters Parameters Description Admin State Allow s you to disable a p ort due to abnormal behavi or (e.g., excessive collisio ns), and then re-enab le it after the problem has been resolved .
AT-FH812 u and AT-FH 824u S oftwar e 18 Defining Port Backu ps Select Backup Li nk Contro l (descr ibe d in Tabl e 1 0) from the Por t Co nfi guratio n screen t o define up t o 15 master/ slave port pai rs. If the connection t o the master port fails, the slave po rt will autom atical ly take ove r.
AT-FH812 u and AT-FH8 24u U ser’s G uide 19 Configuring Port Secur ity Select Por t Security Cont rol fr om the Port Conf igurat io n scre en to co nfi gure port intr usion protec tion. The parameters are descri bed in Figur e 12 and Table 11. ------ ------- --------- --------- ------ Port Security Control (1 - 12) Hub ID : 1 Port Mode Auth.
AT-FH812 u and AT-FH 824u S oftwar e 20 RMON Configuration Use the RMON C onfiguration screen (Fi gure 13) to enable/ disable RMON su pport or to attach the Age nt Module to either the 10 or 100 Mbp s segment. Tab le 12 describes the RMO N config urat ion para me ters.
AT-FH812 u and AT-FH8 24u U ser’s G uide 21 Download ing System Software Using TFTP Protocol to Download o ver the Network. Use the TFTP Download menu t o load software updates into th e hub. The do wnload file should be an atiflash.bi n binary file from Allied Telesyn; ot herwise the ag ent will n ot accept it.
AT-FH812 u and AT-FH 824u S oftwar e 22 Using the Serial Port t o Download via Out- of-B and Use the XModem Downlo ad command to update available softwar e in the hub. The downlo ad file should be the atiflash.bin binary fil e fr om Al lie d T eles yn; otherwi se the agent w ill not acc ept it.
AT-FH812 u and AT-FH8 24u U ser’s G uide 23 Changing System Passwords The User Passwords screen is used to display or modify user names and passwords for t he on-board conf iguration program. T here are two use r types: Admi nistrator and Guest. O nly the Admini strator has writ e access for par a meters governin g the SNMP agent.
AT-FH812 u and AT-FH 824u S oftwar e 24 Displaying Repeater Statistics Use the Repeater Statis tics screen to display stati stics for the 10 Mbps an d 100 Mbps stack seg ments. These valu es can be use d to indicate t he approximate loading f or each segment, as shown in Figure 16 and defi ned in Table 17.
AT-FH812 u and AT-FH8 24u U ser’s G uide 25 Displaying Hub Statistics Use the Hub Stati stics screen to display key statistics for each hub in the stack. Overall stat istics on th e traffic passing through each h ub are displayed. See Figur e 1 7 and Ta ble 1 8.
AT-FH812 u and AT-FH 824u S oftwar e 26 Displaying Port Statistics Use t he Port Statisti cs scree n to di splay ke y statistic s for each p ort. Overa ll stati stics on the t raffic passin g through each port are di splayed. This informati on can be used to identify p otential pr oblems with th e hub (e.
AT-FH812 u and AT-FH8 24u U ser’s G uide 27 T able 19 P or t Statistics Statistics Descriptio n Refresh Statistics Refresh the displayed stati stics. Auto-Refresh Statis tics Refresh statistics at the interval specified in Console Confi guration. Reset Counter Reset the statistics counter for all items to zero.
AT-FH812 u and AT-FH 824u S oftwar e 28 Trou bleshooti ng Refer to th e AT-FH812u and AT-FH824u Installation Guide for a more det aile d listing of troubl eshooting pr ocedures. However, if you have troubl e making a connec tion via Telnet or accessing the w eb or SNMP agent, then please r efer to the follo w in g se cti on.
デバイスAllied Telesis fast ethernet 10/100 hubsの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Allied Telesis fast ethernet 10/100 hubsをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAllied Telesis fast ethernet 10/100 hubsの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Allied Telesis fast ethernet 10/100 hubsの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Allied Telesis fast ethernet 10/100 hubsで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Allied Telesis fast ethernet 10/100 hubsを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAllied Telesis fast ethernet 10/100 hubsの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Allied Telesis fast ethernet 10/100 hubsに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAllied Telesis fast ethernet 10/100 hubsデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
