888 DigitalメーカーHD4000の使用説明書/サービス説明書
ページ先へ移動 of 27
HD4000.
.
1 Safety Instructions • Always read the safety instructions carefully • Keep this User's Manual for future reference • Keep this equipment away from humidit y • Place this equipment on a reli abl e flat surface before setting it up. • Do not stand it on soft furnishings.
2 T able Of Content s Introduction ............................................................................................ 3 Front panel and rear panel illustration ................................................. 4 Front P anel ................
3 Introduction This DVB-T TV Receiver is a Free-T o-Air di gital terrestrial receiv er, allo wing you to access free-to-air digital terrestrial TV channels an d radio broadcasts on your T V set.
4 Front panel and rear panel illustration Front Panel ① ① Green Light To indicate the Stand-by mode ON/OFF (this mode is co ntrolle d by remote control only). Rear Panel ① ANT I N con nect the antenna here. ② LOOP OUT To connect a RF signal from the STB to either the RF Input jack (antenna) on your VCR or to the antenna inp ut of your TV.
5 Remote control Remote key functions: 1. POWER To turn the Stand-by mode ON/OFF. 2. INFO To display the current program information. 3. Numeric buttons (0-9) To control the numerical operation and es pecially to change program directly. 4. SUBT To switch the close caption ON/OFF.
6 Installing the batteries Remove the battery cover fr om the remote control and put two AAA size batteries inside the compartment. The diagram inside the battery compartment shows the correct way to install the batteries. Caution: 1. Keep batteries out of children’s reach.
7 Installation and Connections How to get good reception • In general you are not required to change the existing antenn a. However if your antenna is not in good condition you shou ld consider replacing them to ens ure uninterrupted digital televis ion viewing.
8 Installation and Connections Connect the STB receiver via YPbPr output and Audio output (for high definition viewing) Connect the STB recei ver via VG A output and Audio outp u t (for high definitio.
9 Installation and Connections Connect the recei ver via HDMI output (for high definition viewing) Audio connect ions via Optic al/Coaxial/Mixed A udio L/R Output.
10 First time installation Note: Be sure to turn o n the main power at the rear of your receiver before using the receiver. After all the connections have been made pr operly, switch on your TV . Make sure the receiver is connected to the mains and press Power to switch the receiver on.
11 Basic operations Switch program 1. Press the NUMERIC keys (0~9) on the remote con trol to select the channel number you want. 2. Press the ▲▼ key on the r emote contr ol or the fr ont panel t o change th e availa ble channels upward /downward. 3.
12 Basic operations Change video output mode Press OUTPUT key to select the matched video monitor be tween YPbPr and VGA. Change TV/Radio mode Press TV/Radio key to change the program list mode between T V and Radio. View program info 1. Press INFO key to view the detailed information of current program.
13 Basic operations EPG (Electric Program Guide) 1. Press EPG key to view the EPG information that are provided by the content providers. 2. Press ▲▼ key to view the event information such as event name, event time. . 3. Press OK key to view the detailed information of the current event.
14 Main menu This section guides you to w alk thro ugh of all o ptions on the Menu screen Navigation in the main menu 1. Press MENU key to bring up the main menu or return previo us. 2. Press ▲▼ key to move upward/down to the desired sub menu. 3. Press OK key to enter into the sub menu y ou select.
15 Main menu Menu Tree Inst allation Scan selected channels Auto scan Program Edit Edit F A V Browse Lock Skip Delete Rename Move System Setup A/V setting Local time setting System information Factory.
16 Installation Auto Scan 1. Go to Main menu > Installation. 2. Press BLUE key to auto scan all the channels. 3. Press EXIT key if you want to stop during the auto scan. Manual Scan 1. Go to Main menu > Installation 2. Press ▲▼ to select the channels you want to scan.
17 Program edit NOTE: If there is no prog ram stored, you c an not access the edit menu. Edit Favourite 1. Go to Main menu > Program edit > TV or Radio list. 2. Press YELLOW key to show the favorite list and then press ▲▼ key to select the desir ed favorite list, press OK key to enter favo rite edit mode.
18 Program edit Delete Program 1. Go to Main menu > Program edit > TV or D key to show a list of Edit modes. ion. . cel the operation. T enu. ename menu > Program edit > TV or Radio list. ress ▲▼ key to select the y to enable the rename function.
19 System setup A/V Output Settings 1. Go to Main menu > Sys tem setup > A/V output setting. output, Scree n aspect, key to confirm. ll 2. Press ▲▼ key to select the options: Resolution, Video Audio output. And press OK to enter submenu of select ed option.
20 User preferences OSD Language Go to Main menu > User preferences > OSD language. Only English is supported for this receiver. OSD Transparency 1. Go to Main menu > User preferences >OSD T ransp arenc y . 2. Press ▲▼ key to select the OSD Transparenc y option, and press OK key to enter submenu.
21 User preferences Parental Control User preferences sele ct the Parental Control option, . Parental Rating l. are available. l guidance year old r old ar old d . Installatio n Menu n Menu . Channel Edit Menu el Edit Menu . Setup Menu etup Menu . User preferences Menu s Menu .
22 Trouble shooting If you experience problems with this receiver or its install atio n, in the first instance roblem Possible cause What to do please read carefully the relev ant sections of this User Manual and this Troubleshooting section.
23 Technical specifications em Specification It Frequency Range o 230MHz VHF: 174MHz t UHF: 470MHz to 862MHz Input Impedance 75Ohms unbalanced Signal Input Level -78~-25dbm T uner Bandwidth 7MHz Demod.
WARRANTY INFORMATION PLEASE NOTE THA T DIGIT AL PRODUCTS GROUP PTY L TD ACT AS THE W ARRANTY AND SER VICE AGENTS FOR THIS Digitel+ PRODUCT . DO NOT RETURN THIS CARD TO DIGIT AL PRODUCTS GROUP IMPORT ANT PLEASE KEEP WARRANTY CARD, PROOF OF PURCHASE AND USER MANUAL IN A SAFE PLACE AS YOU WILL REQUIRE THESE WHEN M AKING A WARRANTY C LAIM.
WARRANTY CONDITIONS 1. Where required by DIGITEL+ / DPG only the original invoic e/receipt is sued by e dealer will be accepted as proof of purchase. covers only defects in the material and workmanship of the product r a period of 12months from t he date of original purchas e.
デバイス888 Digital HD4000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
888 Digital HD4000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこには888 Digital HD4000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。888 Digital HD4000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。888 Digital HD4000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
888 Digital HD4000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又は888 Digital HD4000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、888 Digital HD4000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわち888 Digital HD4000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
