AllstarメーカーMH5011Sの使用説明書/サービス説明書
ページ先へ移動 of 20
INST ALLA TION AND OWNER’S MANUAL MJ501 1S & MH501 1S MS SERIES JACKSHAFT COMMERCIAL VEHICULAR DOOR OPERA T ORS READ THIS MANUAL CAREFULLY BE FORE INSTA LLATION OR USE.
READ THESE STATEMENTS CAREFULLY A ND FOLLOW THE INSTRUCTIONS CLOSELY. The Warning and Caution boxes throughout th is manual are there to protect you and your equipment. Pay close at tention to th ese boxes as you follow the manual. WARNING Indicates a MECHANICAL hazard of INJURY OR DEATH.
The purpose of this booklet is to provide assem bly, installation and operatio n inf ormation concerning Allstar Model MJ5011S & MH5011S (MS Series) Comme rcial Vehicular Gara ge Door Operator s and related Acc essory Products.
Before starting the installation of the operator , the door must be in good work ing condition a nd prop erly counterba lanced. I nspect the door and track for loos e or mis sing hardw are. Test the door manual ly for balance and ease of operation . Lubricate d oor hinges and rollers.
T O REDUCE THE RISK OF SEVERE INJUR Y O R D E A TH : R E AD AN D F O L L O W AL L INST A LL A TION INSTRUCTIONS! WARNING ♦ Install only on a pro perly balanced g arage door.
SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES A ND C AN CA USE SEVE RE INJURY OR DEATH IF DISTURBED. DO NOT ATTE MPT ADJUSTMENT. F igure 4, page 7 illustrates several positions suitable for mounting the operator; right hand or left hand, either w all mount or ceiling mount.
CHAIN HOIST AND FLOOR DISC ONNECT INSTALLATI ON I f the operator is furnished w ith a chain hoi st (Model MH5011S), pass the hand chain over t he chai n w heel and through the chain guides on the operator clutch sh aft (opposite end f rom the large pulley).
100769 100771 FIGURE 5 - OPER A T OR DIMENSIONS - MODEL MJ501 1S 8 FIGURE 5A - O PER A TOR DIMENSIONS - MODEL MH501 1S.
A - REVERSE CUTOUT LIMI T SWITCH B - OPEN LIMIT SWITCH C - OPEN LIMIT NUT D - LIMIT NUT RETAINI NG BRACKET E - REVERSE CUTOUT LIMIT NUT F - “V” BRACKET SETTING THE LIM IT SWITCHES 1) With the cover open on the electrical enclosure, ref erence Figure 6 below .
INST A LL A T ION INSTRUCTIONS - ELECTRICAL WIRING TO A VOID DA MA GE TO DOOR A ND OPERATOR ENSURE A LL DOOR LOCKS ARE DIS ABLED. USE A N INTERLOCK SW ITCH IF A LOCK IS REQU IRED TO R ETA IN FU NCTIONA LTY. CAUTION RISK OF ENTRAPMENT TH A T M A Y RESULT IN SERIOUS PERSONAL INJURY OR DE A TH .
DOOR EDGE INST A LL A T ION & WIRING Figure 8 11 OPEN TB1 STOP CLOSE OPEN COM CLOSE STOP NO REV NC REV PHOTO COM SINGLE ILOCK 24 VAC COM SAFE FINI SH PHOTOBEAM 3-WIRE PHOTOBEAM MOTOR CON TR OL BOA.
INST A LL A TIO N INSTRUCTIONS 12 Figure 10 NOTE: It is no w necessary to turn on the power in ord er to to change the Operating Mode (if applicable), program any changes de sired to the operator’s other settings, check for proper operation, and finalize any ad justments to include the lim it settings.
OPER A TION & A DJUSTMENT INSTRUCTIONS 13 IMPORT A NT SA FETY INSTRUCTIONS FOR OWNER • Understand all of the operating features of your door control system at the time of its installation. Your inst alling dealer will demonstrate them for you. • NEVER let children operate or pl ay with door contro ls.
OPERA TION & A D JUSTMENT INSTRUCTIONS 14 CLUTCH A DJUSTMENT The clutch serves to prote ct th e door, the electri c op erator and other equipment from undue stress or damage caused by starting forces and/or an obstruction to the door.
OPER A TION & A DJUSTMENT INSTRUCTIONS 15 B R AK E AD J U S T M E N T Figure 14 Brake Adjustment The brake is adjusted at the factory and m a y need periodic adjustment for wear. When adjustment becomes necessary see Figure 14 at rig ht for the adjustment procedure.
OPERA TION AND ADJUSTMENT INSTRUCTI ONS 16 B2 Operati on Open Button : Momentary activation; open override of c losing door. Close Button : Momentary activation.
OPER A TION & A DJUSTMENT INSTRUCTIONS 17 Setup Modes Various operating characteristics can be m odified via the setup modes. The operator is moved to the close limit position and the on-board dip sw itches (s ee Figure 15) are TEMP ORARILY set according to the table at righ t to enter a Se tup Mode.
OPERA TION AND ADJUSTMENT INSTRUCTI ONS 18 Following installation, the op erator MUST be tes ted and respond correctly to all controls as specified on th e wiring diagram. KEEP personnel and equipm ent clear of the area beneath the door w hen performing the tests.
WIRING DI A GR A M 19 CDO MCB 2005 EDGE RADIO c.p. ALLSTAR CORP. P4 24V S1 R58 R56 R55 R54 R45 R46 R53 PCB 112695 REV B TS LK K2 K4 K3 K5 K6 COM OLS CLS COM HIGH VOLTAG E OPEN MO4 MO3 MO2 MO1 ILK 24V .
Manufacturer’s Lim ited Warranty Linear L LC w arrants it s Allsta r bran d commerc ial do or oper ators to be free fr om defect in material and work manshi p for a period of two ( 2) years from the da te of purchase . To obtain service contac t your dealer.
デバイスAllstar MH5011Sの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Allstar MH5011Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAllstar MH5011Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Allstar MH5011Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Allstar MH5011Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Allstar MH5011Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAllstar MH5011Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Allstar MH5011Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAllstar MH5011Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。