AlpineメーカーCDA-7846Eの使用説明書/サービス説明書
ページ先へ移動 of 55
R CDA-7846E FM/AM Compact Disc Receiver • OWNER'S MANUAL (page 2- page 55) Please read this manual to maximize your enjoyment of the outstanding performance and feature capabilities of the equipment, then retain the manual for future reference.
2 English Precautions This label is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions will result severe injury or death. W arning Caution This label is intended to alert the user to the presence of important operating instructions.
3 English Contents Page 4 .......................................................................................... Precautions 7 ...................................................................... Detachable Front Panel Basic Operation 8 ........
4 English Thermal Be sure the temperature inside the vehicle is between +60°C (+140°F) and –10°C (+14°F) before turning your unit on. Moisture Condensation You may notice the CD playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.
5 English Inserting Discs Your player accepts only one disc at a time for playback. Do not attempt to load more than one disc. Make sure the label side is facing up when you insert the disc. Your player will automatically eject any disc that is inserted incorrectly.
6 English Precautions Installation Location Make sure the CDA-7846E player/receiver will not be exposed to: • Direct sun and heat • High humidity • Excessive dust • Excessive vibrations Handling the Detachable Front Panel • Do not expose to rain or water.
7 English 1 Detaching the Front Panel Press the PWR (Power) button to turn off the power. Press the RLS (release) button until the front panel pops out. Grasp the left side of the front panel and pull it out. Notes: • The front panel may become hot (especially the connector terminals), this is not malfunction.
8 English Basic Operation Initial System Start-Up 1 When operating the unit for the first time after installation or after the vehicle's battery has been disconnected and reconnected, set the volume level to its minimum, then remove the detachable front panel.
9 English Basic Operation 1 1 T urning Power On and Of f Press the PWR button to turn off the unit. The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press the PWR button again to turn off the unit.
10 English Basic Operation Subwoofer On and Of f Change the setting when an optional product having the Subwoofer output terminals is Ai- NET connected. Press and hold the PWR button for at least 3 seconds. Press the F1 button repeatedly to select "SUBW.
11 English Basic Operation 1 Non Fading Pre-Out (N.F .P .) On and Of f Press and hold the PWR button for at least 2 seconds. Press the F1 button. With each press, N.F.P. is toggled On or Off. N.F.P. ON: In this position, the Front Pre- Output will not be affected by the fader.
12 English Basic Operation 1 2 Adjusting Volume/Bass/ Treble/Balance/Fader Press the MODE/LOUD button repeatedly to choose the desired mode. Notes: • If the or button is not pressed in 5 seconds after selecting the BASS, TREBLE, BALANCE and FADER modes, the unit automatically returns to the VOL mode.
13 English Basic Operation 1 1 Audio Mute Function Activating this function will instantly lower the volume level by 20 dB. Press the F6 button to activate the MUTE mode. The volume bar graphic indicator will flash in the display and the audio level will decrease by about 20 dB.
14 English Basic Operation Adjusting Display Contrast You can adjust the display contrast for better visibility. Press and hold the PWR button for at least 2 seconds. Press the F3 button. The "CONTRAST" is displayed. Press the or button to adjust the contrast of the display.
15 English Basic Operation T urning Mute Mode On/Of f With a cellular phone or navigation system connected, audio will be interrupted whenever a call is received. This function can be manually turned ON or OFF from the head unit by following procedure below.
16 English Basic Operation Demonstration In the Demonstration (DEMO) mode, the unit scans each function of the sources; Tuner, CD player and CD shuttle if an optional CD Shuttle is connected. Press the DEMO button to activate the DEMO mode. The DEMO mode is activated and the unit automatically performs the operation.
17 English Basic Operation Displaying Time Press the CLK (CLOCK) button to display the time. The unit displays the time. Note: Selecting any tuner or CD function while in the Clock mode will interrupt the time display momentarily. The function selected will be displayed for about 5 seconds before the time returns to the display.
18 English Basic Operation Setting Time Press the CLK (CLOCK) button to display the time. Note: If the power to the unit is off, turn the power. Press and hold the CLK (CLOCK) button for at least 2 seconds. The time indication will begin to blink. Press the F4 button while the time indication is blinking to set seconds to "0".
19 English Basic Operation 1 2 FUNC F1 F2 F3 F4 F5 F6 Mode Function indicator (on/ off) Radio Preset 1 P–DN (Preset DOWN) P–UP (Preset UP) D.A.P. (Direct Access Memory Preset) MONO (Stereo/Monaural) T.RCL (Tuner Recall) MUTE D–DN (Disc DOWN) D–UP (Disc UP) M.
20 English Radio Operation 4 1 Manual T uning Press the SOURCE button to select the radio mode. Press the BAND button repeatedly until the desired radio band is displayed. Press the TUNE button repeatedly until "MANUAL" appears in the display.
21 Réception radio English Radio Operation 1 2 3 4 Automatic Seek T uning Press the SOURCE button to select the radio mode. Press the BAND button repeatedly until the desired radio band is displayed. Press the TUNE button to illuminate the DX and SEEK indicators in the display.
22 English Radio Operation 1 Manual Storing of Station Presets 1. Tune in the desired radio station you wish to store in the preset memory. 2. Check that the "FUNC" indicator is off. 3. Press and hold any one of the preset buttons (1 through 6) for at least 2 seconds.
23 Réception radio English Radio Operation 1 2 3 Automatic Memory of Station Presets Press the SOURCE button to select the radio mode. Press the BAND button repeatedly until the desired radio band is displayed. Press and hold the A. ME button for at least 2 seconds.
24 English Radio Operation Storing into Direct Access Preset (D.A.P .) Band A combination of radio stations in any band, AM and FM (up to 6 stations) can be manually preset onto the D.A.P. band. Press the F3 button when the "FUNC" indicator is on.
25 Réception radio English Radio Operation 1 2 T uning to Preset Stations Press the SOURCE button to select the radio mode. Press the BAND button repeatedly until the desired band is displayed. To select the D.A.P. band, press the F3 button with the "FUNC" indicator on.
26 English Radio Operation 1 Displaying Station Titles If a title has been entered for the selected station, it can be displayed in place of the frequency. The display will toggle between the frequency and title display with each press of the TITLE button.
27 Réception radio English Radio Operation 1 Titling Stations Tune in a station to be titled. Change to the TITLE mode. Press and hold the TITLE button for at least 2 seconds. The first digit will blink. Press FUNC button to select the desired mode. It will change each time you press the button.
28 English Radio Operation 6 5 Titling Stations (Continued) Press the TITLE button to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title.
29 Réception radio English Radio Operation 1 1 F5 T.RCL F5 T.RCL (OFF) (ON) F4 MONO F4 MONO (OFF) (ON) F5 F4 Displaying Station Signal Strength [T.RCL (T uner Re- call)] You can display the signal strength of a desired radio station while you are listening to other sources such as CD player or CD Shuttle.
30 English CD Operation 1 2 3 Inserting Disc Note: When a CD is located in the CD player, the "DISC IN" indicator illuminates. Press the OPEN button to open the front door. The CD compartment is located behind the front door. Insert a CD half way into the slot with the label side facing up.
31 English CD Operation Removing Disc Press the OPEN button to open the front door. Press the Eject ( ) button on the top side of the front door. The CD is automatically ejected half way out.
32 English CD Operation 1 2 Normal Play and Pause Insert a CD into the CD player. The CD player begins playback from the first track on the disc. The display shows the track number and elasped time of the track being played. When the last track is played back the player returns to the first track and begins playback from that point.
33 English CD Operation 1 Music Sensor (Skip) Momentarily press the ( ) DN button once to return to the beginning of the current track. If you wish to access a track further back, repeatedly press until you reach the desired track. (The example shows the Music Sensor operation starting from track No.
34 English CD Operation 1 Repeat Play Press the F4 button to play back repeatedly the track being played. The RPT indicator appears and the track will be played repeatedly.
35 English CD Operation M.I.X. (Random Play) Press the F3 button in the play or pause mode. The M.I.X. indicator will illuminate and the tracks on the disc will be played back in a random sequence. After all the tracks on the disc have been played back once, the player will begin a new random sequence play until the M.
36 English CD Operation 1 2 Scanning Programs Press the F5 button to activate the Scan mode. The first 10 seconds of each track will be played back in succession.
37 English CD Operation 1 NORMAL Mode CLOCK PRIORITY Mode CD TITLE Mode Title not entered T o Display CD Titles After a title has been entered for a CD, it can be displayed by pressing the TITLE button. The display will toggle between Normal, Clock and CD Title with each press of the TITLE button (see example below).
38 English CD Operation Titling Disc Select a disc for which you want to enter a title. Change to the TITLE mode. Press and hold the TITLE button for at least 2 seconds. The first digit will blink. Press the FUNC button to select the desired mode. The mode will change each time you press the button.
39 English CD Operation Titling Disc (Continued) Press the TITLE button to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title.
40 English CD Operation 1 4 5 2 3 Erasing Disc Title Press the TITLE button to select the disc titling mode. Then, press and hold for at least 2 seconds. Press and hold the FUNC button for at least 2 seconds to activate the title scanning mode. The title in the display will blink, for example "ALPINE".
41 English CD Shuttle Operation Controlling CD Shuttle (Optional) An optional 6-disc or 12-disc CD Shuttle may be connected to the CDA-7846E if it is Ai-NET compatible. With a CD Shuttle connected to the Ai-NET input of the CDA-7846E, the CD Shuttle will be controllable from CDA-7846E.
42 English CD Shuttle Operation Controlling CD Shuttle (Optional) (Continued) Press the Function button (F1 through F6) corresponding to one of the discs loaded in the CD Shuttle. The selected disc number appears in the display and CD playback starts.
43 English CD Shuttle Operation Sear ching Titled Discs (Title Sear ch Menu) Press the TITLE button to activate the Title Display mode. Press and hold the T.S.M. button for at least 2 seconds while the title is displayed. The title in memory blinks in the display.
44 English CD Shuttle Operation Multi-Changer Selection Alpine’s Ai-NET system will support up to 6 CD Shuttles. When operating two or more changers, the KCA-400C (Multi-Changer Switching device) must be used. If you use 1 Switching device, you can connect up to 4 CD Shuttles.
45 English CD Shuttle Operation 4 Multi-Changer Selection (Continued) BAND PROG Remote Control RUE-4185 BAND PROG SOURCE A.PROC 3 Press the BAND button on the Remote Controller until the desired changer indicator appears on the display. To operate the selected changer, see "CD Operation" section.
46 English Remote Contr ol Controls 1 Mute Button Press the button to lower the volume by 20 dB instantly. Press the button again to cancel. 2 Power Switch Press the s witch to tur n the power on/off . 3 Button Press the button to switch between the Play and Pause modes for the CD.
47 English Remote Contr ol 8 Button Radio mode: SEEK (DN) Button CD/CD Shuttle mode: Press the button to go back to the beginning of the current track. 9 Button Radio mode: SEEK (UP) Button CD/CD Shuttle mode: Press the button to advance to the beginning of the next track.
48 English Remote Contr ol Battery Replacement Applicable battery: Use two "AAA" sized dry batteries or equivalent. Opening the battery cover Slide out the battery cover while firmly pressing outward. Replacing the battery Put the batteries in the case as illustrated.
49 English Correct Handling Do not drop the disc while handling. Hold the disc so you will not leave fingerprints on the surface. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc. Disc Care Disc Cleaning Fingerprints, dust, or soil on the surface of the disc could cause the CD player to skip.
50 English Cause and Solution • Car's ignition is off. – If connected per instructions, the unit will not operate with the car's ignition off. • Improper connection of power leads. – Check connections of the power leads. • Blown fuse.
51 English In Case of Dif ficulty Radio Mode Symptom Unable to receive stations. Unable to tune stations in the seek mode. Broadcast is noisy. Cause and Solution • No antenna or open connection in cable. – Make sure the antenna is properly connected; replace the antenna or cable if necessary.
52 English CD Mode In Case of Dif ficulty Symptom CD insertion not possible. Unable to Fast-Forward or Backward. Sound skips due to vibration. Sound skips without vibration. Cause and Solution • There is a CD already in the transport. – Eject the CD in transport and remove it.
53 English Indication for CD Shuttle Indication Cause and Solution • Protective circuit is activated due to high temperature. – The indicator will disappear when the temperature returns to within operation range. • Disc won't return to magazine.
54 English Specifications FM TUNER SECTION Tuning Range ...................................................................................................... 87.5 – 108.0 MHz Mono Usable Sensitivity .................................................
55 English Specifications GENERAL Power Requirement ..................................................................... 14.4V DC (11 – 16V (allowable)) Maximum Power Output ..........................................................................
デバイスAlpine CDA-7846Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Alpine CDA-7846Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAlpine CDA-7846Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Alpine CDA-7846Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Alpine CDA-7846Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Alpine CDA-7846Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAlpine CDA-7846Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Alpine CDA-7846Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAlpine CDA-7846Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。