FMIメーカーCGCFTPAの使用説明書/サービス説明書
ページ先へ移動 of 32
For more information, visit www .fmiproducts.com W ARNING: If the information in this manual is not .
www .fmiproducts.com 124978-01B 2 SAFETY T ABLE OF CONTENTS Safety .................................................................. 2 Local Codes......................................................... 4 Product Identication ....................
www .fmiproducts.com 124978-01B 3 this heater or its controls can W ARNING: Do not.
www .fmiproducts.com 124978-01B 4 SAFETY Continued 10. This repl ace need s fresh air vent ilat ion to run pro perl y . This repl ace has an Oxyg en Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the re - place if not enough fresh air is available.
www .fmiproducts.com 124978-01B 5 PRODUCT FEA TURES ASSEMBL Y Figure 2 - Assembling Fireplace Log Screen Burner Support with Log Locator T abs Branch Support Shoulder Screw This replace has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system.
www .fmiproducts.com 124978-01B 6 ASSEMBL Y Continued 1. Lo cat e f our b lac k p hil lip s s hee t met al screws from the hardware packet. 2. Rotate hood as shown in Figure 3. Make sure hood tabs point toward replace.
www .fmiproducts.com 124978-01B 7 .
www .fmiproducts.com 124978-01B 8 W ARN IN G: If the area in wh ich .
www .fmiproducts.com 124978-01B 9 INST ALLA TION IMPORT ANT : V ent-free replaces add mois - ture to the air . Although this is benecial, installing replace in rooms without enough ventilation air may cause mildew to form from too much moisture.
www .fmiproducts.com 124978-01B 10 W ARNING: Maintain the minimum clearances shown .
www .fmiproducts.com 124978-01B 11 IMPORT ANT : When nishing your rebox, combustible materials W ARNING: Do not allow any .
www .fmiproducts.com 124978-01B 12 W ARNING: Never modify or cover the louvered slots on the .
www .fmiproducts.com 124978-01B 13 INST ALLA TION Continued 9. Check all gas connections for leaks. See Checking Gas Connections, page 18. 1 0. Carefully insert fireplace into cabinet mantel (see Figure 13). Be careful not to scratch or damage hearth base or cabinet mantel.
www .fmiproducts.com 124978-01B 14 INST ALLA TION Continued Figure 16 - Removing V alve Cover Shield 1 2 Remove Screw V alve Cover Shield Shoulder Screw Branch Support Snap Bushings Bottom Louver Assembly 4. Carefully disconnect green and white wires at their insulated connectors.
www .fmiproducts.com 124978-01B 15 INST ALLA TION Continued Figure 18 - Installing Switch Plate to V alve Cover Shield Switch Plate Screw V alve Cover Shield .
www .fmiproducts.com 124978-01B 16 INST ALLA TION Continued - .
www .fmiproducts.com 124978-01B 17 INST ALLA TION Continued Inst allat ion must include an equipm ent shutof f valve, union, and plugged 1/8" NPT tap. Lo - cate NPT tap within reach for test gauge hook up. NPT tap must be upstream from replace (see Figure 22).
www .fmiproducts.com 124978-01B 18 INST ALLA TION Continued .
www .fmiproducts.com 124978-01B 19 INST ALLA TION Continued CONNECTIONS 1. Op en eq uip me nt sh ut of f va lve (s ee Fi gur e 25, page 18). 2. Open main gas valve located on or near gas meter for natural gas or open pro - pane/LP supply tank valve.
www .fmiproducts.com 124978-01B 20 Note: If pilot does not stay lit, refer to T roubleshooting, page 24. Also contact a qua lie d servi ce pers on or gas suppl ier for repairs. Until repairs are made, light pilot with match. T o light pilot with match, see Manual Lighting Procedure, page 21.
www .fmiproducts.com 124978-01B 21 TO TURN OFF GAS Shutting Off Fireplace 1. T urn control knob clockwise to the OFF position. 2. T urn off all electric power to the appliance if service is to be performed. 3. Clo se equi pme nt shut of f valv e (see Figu re 25, page 18).
www .fmiproducts.com 124978-01B 22 Thermocouple Pilot Burner Figure 31 - Correct Pilot Flame Pattern (Propane/LP Shown) Thermocouple Pilot Burner Figure 32 - Incorrect Pilot Flame Pattern (Propane/LP Shown) Figure 33 shows a correct burner ame pat - tern.
www .fmiproducts.com 124978-01B 23 CLEANING AND MAINTENANCE 4. Check orice holder located at end of burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle. 5. Blow air into primary air holes on orice holder .
www .fmiproducts.com 124978-01B 24 TROUBLESHOO TING .
www .fmiproducts.com 124978-01B 25 1 . Control knob not fully pressed in 2. Control knob not pressed in long enough 3. Safety interloc k system has been triggered 4. Equi pmen t shuto f f valve not fully open 5.
www .fmiproducts.com 124978-01B 26 TROUBLESHOO TING Continued 1. Residues from manufac tur- ing processes 1. Turning control knob to HI position when burner is cold 2. Air in gas line 3. Air passageways on re - place blocked 4.
www .fmiproducts.com 124978-01B 27 .
www .fmiproducts.com 124978-01B 28 SERVICE HINTS • pilot will not stay lit • burner will have delayed ignition.
www .fmiproducts.com 124978-01B 29 ACCESSORIES W ALL MANTEL AND FULL HEARTH - Unnished, T raditional Design - Oak Finished, T raditional Design - Oak Finished, Georgian Design Mantel features clean, classic lines.
www .fmiproducts.com 124978-01B 30 P ARTS 23 29 40 32 36 38 13 7 8 33 40 1 1 10 4 7 30 1 3 2 9 .
www .fmiproducts.com 124978-01B 31 P ARTS This list contains replaceable parts used in your replace. When ordering parts, follow the instructions listed under Replacement Parts on page 28 of this manual.
124978-01 Rev . B 06/10 WARRANTY KEEP THIS WARRANTY FMI PRODUCTS, LL C LIMITED WARRANTIES Standard W arranty: FMI PRODUCTS, LLC warrants this new product and any p.
デバイスFMI CGCFTPAの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
FMI CGCFTPAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFMI CGCFTPAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。FMI CGCFTPAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。FMI CGCFTPAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
FMI CGCFTPAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFMI CGCFTPAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、FMI CGCFTPAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFMI CGCFTPAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。