Fordメーカー1の使用説明書/サービス説明書
ページ先へ移動 of 73
EXPEDITION EXPEDITION EL -/$)&)%23'5)$% 30%#)!,3%2 6)#%6%()#,%336  2010 2010.
T ABLE OF CONTENTS 1 General Information 2 Electrical 3 Installation Considerations 4 Cargo Mounting Considerations 5 Reference Information INTRODUCTION SECTIONS N OTE: The descriptions and specifications contained in this manual were in effect at the time this manual was approved for printing.
SECTION 0 Introduction Contents Introduction ....................................................................................... 0-1 2010 Expedition SSV Modifiers Guide, 07/2009.
Introduction 0-1 Introduction Ford Motor Company has assembled this Expedition Special Service Vehicle (SSV) Modifiers Guide to assist vehicle modifiers in producing safe and quality products. Ford believes that safety and quality come first. This book is divided into topics pertinent to modifiers of vehicles.
SECTION 1 General Information Contents Section 1: General Information ........................................................ 1-1 Important Safety Notice ................................................................ 1-1 Warnings, Notices and Notes .
General Information 1-1 Section 1: General Information Important Safety Notice Note: The descriptions and specifications contained in this guide were in effect at the time this manual was approved for printing.
1-2 General Information Section 1: General Information The following list contains some general warnings that you should follow when you work on a vehicle. WARNING: • Always wear safety glasses for eye protection. • Use safety stands whenever a procedure requires you to be under the vehicle.
General Information 1-3 Section 1: General Information Special Service Vehicle (SSV) Definition Special Service Vehicles (SSV) are offered to fill the special needs of police agencies that a standard patrol car can not.
1-4 General Information Section 1: General Information Standard Equipment System Description Interior Second and third row coat hooks Second row map lights Manual A/C with auxiliary climate controls A.
General Information 1-5 Section 1: General Information Miscellaneous Options (See sales brochure for complete list of available options) Item Description Exterior Options Daytime running lamps (43D) E.
1-6 General Information Section 1: General Information Vehicle Certification (VC) Label Code Positions Position Description 1 Exterior paint code 2 Region code 3 District Special Order (DSO) 4 Wheelba.
General Information 1-7 Section 1: General Information 1. Exterior Paint Color Code The first set of numbers/letters listed indicate the vehicle primary body color code. The second set of letters/numbers listed (if applicable) indicate a 2-tone or accent body color code.
1-8 General Information Section 1: General Information 7. Radio Type • 1 — AM/FM stereo with in-dash, 6-disc CD changer and clock • F — AM/FM stereo CD player, navigation system and clock • .
General Information 1-9 Section 1: General Information 11. Powertrain Calibration Information Powertrain calibration information is printed in the lower right corner of the VC label. Only the base calibration information is printed. Revision levels will not appear.
1-10 General Information Section 1: General Information New Vehicle Storage — Body • Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces and underside of front fender. • Periodically wash vehicles stored in exposed locations.
General Information 1-11 Section 1: General Information Tire Pressure Monitoring System (TPMS) Principles of Operation The tire pressure monitoring system (TPMS) monitors the air pressure of all 4 regular road tires.
1-12 General Information Section 1: General Information The TPMS, as delivered from the Ford Motor Company, complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
General Information 1-13 Section 1: General Information As the ambient temperature decreases by 6 ° C (10 ° F), tire pressure decreases 7 kPa (1 psi). Adjust the tire pressure by 7 kPa (1 psi) for each 6 ° C (10 ° F) ambient temperature drop as necessary to keep the tire at the specified vehicle certification (VC) label pressure.
SECTION 2 Electrical Contents Section 2: Electrical ......................................................................... 2-1 Electrical Basics ........................................................................... 2-1 Electrical Systems Management .
Electrical 2-1 Section 2: Electrical Electrical Basics Inside a vehicle, electricity is supplied through powered wires (commonly called ‘‘hot’’ wires), comparable to the pressurized supply pipes of a plumbing system. At various points along the wires are outlets in the form of lights, switches and receptacles.
2-2 Electrical Section 2: Electrical Electrical Systems Management Care must be given in deciding what equipment should be installed into a police vehicle given the power demands of the equipment and the power available from the vehicle. A power load strategy should be developed to minimize the risk of running out of power.
Electrical 2-3 Section 2: Electrical Component Amps Base Miscellaneous Base Loads 16.5 Cooling Cooling Fan (electric fan clutch) 2.2 Climate Control A/C Clutch 3.5 A/C Fan-to-Face — High Speed 18.9 A/C Fan-to-Face — M/H Speed 13.4 Heater Fan-to-Foot — M/H Speed 12.
2-4 Electrical Section 2: Electrical PCM — Red Area NOTICE: DO NOT make electrical connections to vehicle electrical systems not specifically designed for police equipment installations. Damage to the electrical system can occur. Do not install any components into the PCM or PCM harness.
Electrical 2-5 Section 2: Electrical • Disconnect the negative battery cable of vehicles stored on site to reduce the possibility of draining the battery by lights or other equipment. • Do not allow control panels attached to the instrument panel to protrude into the driver and passenger air bag deployment zones.
2-6 Electrical Section 2: Electrical Equipment Grounding Guidelines • Do not ground the body to the transmission or transmission crossmember. Ground accessories to the chassis or the vehicle battery.
Electrical 2-7 Section 2: Electrical • Determine the terminal type. Base your decision on wire gauge, current carrying capacity, connector type and insulation type. — Use non-detent low insertion force terminals whenever possible. — Do not use low insertion force female terminals in weather-resistant connectors.
2-8 Electrical Section 2: Electrical • Use 135% of the fuse rating when sizing wiring to protect the circuit in the event of an overload. Fuses will last for 1 hour at 135% of their rating.
Electrical 2-9 Section 2: Electrical • Use greased or sealed connectors in floor pan troughs which are subject to moisture coming through the carpeting. • Use XLPE insulation for uncovered runs that exceed 305 mm (12 in). Electrical Protection • Correctly route wires away from noise-generating wires or components.
2-10 Electrical Section 2: Electrical • Scroll — Similar to convolute, but without the ridges. Scroll is used where harness rigidity is required, especially for maintaining critical locator dimensions. Use scroll for short lengths only, as it is quite inflexible.
Electrical 2-11 Section 2: Electrical • Route wires to avoid metal edges, screws, trim fasteners and abrasive surfaces. When such routing is not possible, use protective devices (shields, caps) to protect the wires. Cover metal edges with a protective shield and fasten the wiring within 76 mm (3 in) on each side of the edge (see figure below).
2-12 Electrical Section 2: Electrical Wire Retention and Routing Use the following criteria to determine the location of retainers: • Size and weight of wire bundle. • Holes with poor accessibility that prevent installation of locators. • Movement of wires that can result in abrasion, squeaks and rattles.
Electrical 2-13 Section 2: Electrical For retainer screws, the following guidelines apply: • Avoid using fasteners that are too long for the application or are in an area which might damage vehicle components, including wiring, brake lines, fuel tank and lines, powertrain components, exhaust system and suspension.
2-14 Electrical Section 2: Electrical Splices and Repairs For quality splicing and to reduce potential problems, the following guidelines are recommended: • Stagger the splices within a harness to reduce increased harness diameter. Splice only on straight areas as installed, not on bends.
Electrical 2-15 Section 2: Electrical 2. Strip wires to appropriate length. 3. Install heat shrink tubing. 4. Twist the wires together. 5. Note: Use resin-core mildly-activated (RMA) solder. Do not use acid-core solder. Solder wires together. 6. Note: Wait for solder to cool before moving wires.
2-16 Electrical Section 2: Electrical 7. Note: Overlap tubing on both wires. Evenly position heat shrink tubing over wire repair. 8. Use a shielded heat gun to heat the repaired area until adhesive flows out of both ends of the heat shrink tubing.
Electrical 2-17 Section 2: Electrical 9. Reconnect the battery ground cable. Sealed Connectors Ford Part Number Part Name Class E6FZ-14488-A Butt Connector C Gauge: 18-22, Color: Red E6FZ-14488-B Butt.
2-18 Electrical Section 2: Electrical 4. Select the appropriate wire slice for the wires to be spliced from Rotunda Wire Splice Kit 164-R5903. 5. Note: Rotunda 164-R5901 Pro-Crimper supplied with the wire splice kit is the only tool that can be used with these splices.
Electrical 2-19 Section 2: Electrical 8. Check for acceptable crimp. (1) Crimp should be centered on each end of the butt splice. (2) Wire insulation does not enter butt splice. (3) Wire is visible through inspection hole of splices. 9. Evenly position supplied heat shrink tubing over wire repair.
2-20 Electrical Section 2: Electrical Rear Power Window Disable The rear power windows of the Expedition SSV can be disabled by disconnecting the rear window motor connectors (C701 [LH] and C801 [RH]). These connectors are located inside the door, behind the door trim panel.
SECTION 3 Installation Considerations Contents Section 3: Installation Considerations.............................................. 3-1 Mobile Radio Installation Guidelines ............................................ 3-1 General Information .........
Installation Considerations 3-1 Section 3: Installation Considerations Mobile Radio Installation Guidelines NOTICE: This information has been prepared for use by persons installing 2-way radio equipment (transmitters and receivers) in vehicles.
3-2 Installation Considerations Section 3: Installation Considerations Radio transmitters are regulated by the Federal Communications Commission (FCC) in the United States. Compliance with FCC regulations is the responsibility of the manufacturer and/or user of transmitter equipment and not Ford Motor Company.
Installation Considerations 3-3 Section 3: Installation Considerations Glass-mounted antennas should be kept as high as possible in the center of the rear window or windshield.
3-4 Installation Considerations Section 3: Installation Considerations If any vehicle radio interaction problems exist after following these guidelines, contact the radio equipment manufacturer for additional assistance.
Installation Considerations 3-5 Section 3: Installation Considerations Item Description 1 Side curtain tether anchor bolt hole 2 A-pillar assist handle bracket lower mounting bolt hole 3 Center line 4 Spotlight shaft hole 5 Spotlight mount lower bolt hole 1.
3-6 Installation Considerations Section 3: Installation Considerations Siren and Grille Lights The engine cooling system relies on correct airflow through the radiator to keep the engine at its correct operating temperature. When adding sirens and grille lights to a vehicle, make sure this airflow is not obstructed.
Installation Considerations 3-7 Section 3: Installation Considerations Safety Belt Retractor and Side Impact Sensor Item Description 1 Side impact sensor 2 Front safety belt retractor The front safety belt retractors are located in the base of the B-pillars.
3-8 Installation Considerations Section 3: Installation Considerations WARNING: The front side impact sensors are located in the front doors. These are pressure sensors that measure the pressure change in the front door during an impact. Do not mount anything on or in the door.
Installation Considerations 3-9 Section 3: Installation Considerations Driver/passenger air bags affect the way police equipment can be mounted in police vehicles. Any surfaces that could come into contact with an air bag during deployment must not damage the air bag or alter its deployment path.
3-10 Installation Considerations Section 3: Installation Considerations A reset event will set the interior lamps interrupt timer to 0. The reset events for the interior lamps interrupt timer are: turning on the interior lamps by using the dome lamp switch or opening any door (as detected by the door ajar switches).
SECTION 4 Cargo Mounting Considerations Contents Section 4: Cargo Mounting Considerations ..................................... 4-1 Cargo Area Equipment Mounting Guide ...................................... 4-1 Safety Belt Retractor and Side Impact Sensor (if equipped).
Cargo Mounting Considerations 4-1 Section 4: Cargo Mounting Considerations Cargo Area Equipment Mounting Guide NOTICE: When installing equipment, it is important to consider the available clearance between the brake lines and the fastener or component.
4-2 Cargo Mounting Considerations Section 4: Cargo Mounting Considerations Item Description 1 Side impact sensor 2 Second row safety belt retractor 3 Third row safety belt retractor The second row safety belt retractors are located in the middle of the C-pillars.
Cargo Mounting Considerations 4-3 Section 4: Cargo Mounting Considerations WARNING: The rear side impact sensors are located in the C-pillars. The installation of hardware must not interfere with the correct operation of the rear side impact sensors. Failure to follow these instructions may result in personal injury.
4-4 Cargo Mounting Considerations Section 4: Cargo Mounting Considerations Cargo Loading WARNING: Ford recommends that police equipment be both secured and laterally aligned. Hard, stiff or sharp objects, especially when not secured or correctly located, pose a risk to the occupants.
Cargo Mounting Considerations 4-5 Section 4: Cargo Mounting Considerations • Low Risk Items — These items are soft in feel and pose a low risk of potential injury capability in collisions.
SECTION 5 Reference Information Contents Section 5: Reference Information .................................................... 5-1 Engineering Drawings .................................................................. 5-1 Air Bag Deployment Interference .
Reference Information 5-1 Section 5: Reference Information Engineering Drawings Air Bag Deployment Interference WARNING: Do not place objects or mount equipment in front of the air bag module cover or.
5-2 Reference Information Section 5: Reference Information Figure 1. (1) 250 mm (9.8 in) from center of air bag door (2) 325 mm (12.8 in) from center of air bag door (3) 650 mm (25.
Reference Information 5-3 Section 5: Reference Information (1) 500 mm (19.7 in) (2) 300 mm (11.8 in) (3) 200 mm (8 in) Figure 3. No objects should be placed between the air bags due to air bag variability. (1) 300 mm (11.8 in) (2) 500 mm (19.7 in) (3) 260 mm (10.
5-4 Reference Information Section 5: Reference Information Figure 4. The curtain airbag extends from the A-pillar to the D-pillar and from the roof rail to the beltline. • Do not mount equipment to the B-, C- and D-pillars above the beltline. • Do not mount equipment to the A-pillar above the beltline except for spotlights.
Reference Information 5-5 Section 5: Reference Information Fuel Lines — Short Wheelbase Item Description 1 Fuel line 2010 Expedition SSV Modifiers Guide, 07/2009.
5-6 Reference Information Section 5: Reference Information Fuel Lines — Long Wheelbase Item Description 1 Fuel line 2010 Expedition SSV Modifiers Guide, 07/2009.
Reference Information 5-7 Section 5: Reference Information Fuel Tank — Cut View, Short Wheelbase Item Description 1 Evaporative emissions hose 2 Fuel tank 3 Fuel line 2010 Expedition SSV Modifiers G.
5-8 Reference Information Section 5: Reference Information Fuel Tank — Cut View, Long Wheelbase Item Description 1 Evaporative emissions hose 2 Fuel tank 3 Fuel line 2010 Expedition SSV Modifiers Gu.
Reference Information 5-9 Section 5: Reference Information Fuel Tank — Bottom View, Short Wheelbase Item Description 1 Fuel lines 2 Fuel tank 2010 Expedition SSV Modifiers Guide, 07/2009.
5-10 Reference Information Section 5: Reference Information Fuel Tank — Bottom View, Long Wheelbase 2010 Expedition SSV Modifiers Guide, 07/2009.
Reference Information 5-11 Section 5: Reference Information Item Description 1 Fuel lines 2 Fuel tank Fuel Tank — Top View, Short Wheelbase 2010 Expedition SSV Modifiers Guide, 07/2009.
5-12 Reference Information Section 5: Reference Information Fuel Tank — Top View, Long Wheelbase 2010 Expedition SSV Modifiers Guide, 07/2009.
Reference Information 5-13 Section 5: Reference Information Fuel Pump Shut-Off Switch Brake Lines NOTICE: When installing equipment, it is important to consider the available clearance between the brake lines and the fastener or component. Any fasteners or static components should allow a minimum of 15 mm (0.
5-14 Reference Information Section 5: Reference Information Item Description 1 Master cylinder 2 Brake booster 3 Brake lines 4 Brake control module Technical Specifications Item Specification Specification Make: Ford Model: Expedition Special Service Sales Code: — Vehicle (SSV) Engine Displacement Cubic Inches: 330 Liters: 5.
Reference Information 5-15 Section 5: Reference Information Item Specification Specification Torque 365 lb-ft @ 3,750 rpm Battery 750 cca Compression Ratio 9.8:1 Transmission Model: 6R80 Type: 6-speed electronic automatic with lockup torque converter and overdrive.
5-16 Reference Information Section 5: Reference Information Item Specification Specification Behind Third Row Seat (optional) 0.51 cu m (18 cu ft) (Expedition) or 1.21 cu m (42.6 cu ft) (Expedition EL) EPA Mileage Est. (mpg) City: 16/Highway: 22 Combined: 18 Mileage Est.
デバイスFord 1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ford 1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFord 1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ford 1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ford 1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ford 1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFord 1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ford 1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFord 1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
