FordメーカーF-150 (2006)の使用説明書/サービス説明書
ページ先へ移動 of 335
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 19 Entertainment Systems 22 AM/FM stereo 22 AM/FM stereo with CD 24 AM/FM stereo cassette with CD 30 AM/FM stereo with in-dash.
Locks and Security 98 Keys 98 Locks 98 Anti-theft system 109 Seating and Safety Restraints 1 13 Seating 113 Safety restraints 119 Airbags 138 Child restraints 147 Tires, Wheels and Loading 164 T ire i.
Cleaning 263 Maintenance and Specifications 273 Engine compartment 275 Engine oil 279 Battery 283 Engine coolant 285 Fuel information 291 Air filter(s) 309 Part numbers 311 Refill capacities 312 Lubricant specifications 315 Engine data 318 Accessories 325 Index 327 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide.
Event Data Recording Other modules in your vehicle — event data recorders — are capable of collecting and storing data during a crash or near crash event.
Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Y our vehicle is not equipped with the Ford Ambulance Preparation Package. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES Base instrument cluster Base with T achometer instrument cluster 2006 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Instrument Cluster 12.
Family carrier instrument cluster Mid instrument cluster 2006 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Instrument Cluster 13.
Luxury instrument cluster Harley-Davidson instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions.
Service engine soon: The Service engine soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction.
Mid and Luxury instrument cluster If the brake system warning light does not illuminate at this time, seek service immediately from your authorized dealer . Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your authorized dealer .
Door ajar: Illuminates when the ignition is in the ON position and any door is open. Overdrive off (if equipped): Illuminates when the overdrive function of the transmission has been turned off, refer to the Driving chapter . If the light flashes steadily or does not illuminate, have the transmission serviced soon, or damage may occur .
MINI MESSAGE CENTER WARNING DISPLAYS (IF EQUIPPED) Door ajar: Displays when the ignition is in the ON position and any door is open. Low fuel: Displays when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Check fuel cap: Displays when the fuel cap may not be properly installed.
GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
Odometer: Registers the total miles (kilometers) of the vehicle. • W ith Mini Message Center • W ith Full Message Center Refer to Message Center in the Drivers Controls chapter on how to switch the display from Metric to English. T rip odometer: Registers the miles (kilometers) of individual journeys.
Battery voltage gauge: Indicates the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range, have the vehicle’ s electrical system checked by your authorized dealer as soon as possible.
AUDIO SYSTEMS AM/FM Stereo System (if equipped) Accessory delay: Y our vehicle is equipped with accessory delay which allows you to operate the window switches and the audio for up to ten minutes after the ignition has been turned off or until either front door is opened.
Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Setting the clock: Press until HR or Mn is displayed. Press / / SEEK to adjust the hours/minutes.
AM/FM Stereo Single CD/Satellite Compatible Sound System (if equipped) AM/FM Stereo Single CD with MP3/Satellite Compatible Sound System (late availability — if equipped) 2006 F-150 (f12) Owners Gui.
1. / T une: In radio mode, press to manually go up ( )o r down ( ) the radio frequency . In menu mode, use to select various settings. In Satellite Radio mode (if equipped), press / to enter TEXT MODE and scroll through the current song title, artist, channel category and Sirius Long Channel Name.
BASS: Press MENU until BASS appears in the display . Use / / SEEK to adjust the bass levels. BAL (Balance): Press MENU until BAL appears in the display . Use / / SEEK to adjust the audio between the left and right speakers. F ADE: Press MENU until F ADE appears in the display .
5. SEEK: In radio mode, press / to access the previous/next strong station. In CD mode, press / to access the previous/next CD track. In Satellite Radio mode (if equipped), press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.
FOLDER: press to access the previous folder on MP3 discs, if folders are available. 10. FF (Fast forward): Press to manually advance in a CD track. 11.
In Satellite radio mode (if equipped), press and release to enter TEXT MODE and display the current song title. While in TEXT MODE, press again to scroll through the current song title, artist, channel category and the SIRIUS long channel name. In TEXT MODE, sometimes the display requires additional text to be displayed.
AM/FM Single CD/Cassette/Satellite Compatible Sound System (if equipped) 1. / T une: In radio mode, press to manually go up ( )o r down ( ) the radio frequency .
2. SEEK: In radio mode, press / to access the previous/next strong station. In CD mode, press / to access the previous/next CD track. In Satellite Radio mode (if equipped), press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.
BASS: Press MENU until BASS appears in the display . Use / / SEEK to adjust the bass levels. BAL (Balance): Press MENU until BAL appears in the display . Use / / SEEK to adjust the audio between the left and right speakers. F ADE: Press MENU until F ADE appears in the display .
7. TEXT : This control currently not supported. 8. SHUFFLE: Press to play CD tracks in random order on the selected CD. 9. COMP (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level. 10. REPEA T : Press to repeat the current CD track.
17. ON/OFF/V olume: Press to turn ON/OFF . T urn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Premium/Audiophile In-Dash Six CD/MP3/Satellite Compatible Sound System (if equipped) Premium/Audiophile In-Dash Six CD/MP3/Satellite Compatible Sound System (late availability — if equipped) 2006 F.
1. / T une/Disc selector: In radio mode, press to manually go up ( ) or down ( ) the radio frequency . In menu mode, use to select various settings. In CD mode, press to select the desired disc.
BASS: Press MENU until BASS appears in the display . Use / / SEEK to adjust the bass levels. BAL (Balance): Press MENU until the balance display appears. Use / / SEEK to adjust the audio between the left and right speakers. F ADE: Press MENU until the fade display appears.
T o activate, press and hold MENU until RDS (ON/OFF) appears in the display . Use / / SEEK to toggle RDS ON/OFF . When RDS is on, press MENU repeatedly to scroll through Find, Show and RDS. When RDS is Off, you will not be able to access Find and Show functions.
5. SEEK: In radio mode, press / to access the previous/next strong station. In CD mode, press / to access the previous/next CD track. In Satellite Radio mode (if equipped), press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.
11. REW (Rewind): Press to manually reverse in a CD track. 12. Memory presets: T o set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset control until sound returns. Y ou may store up to six stations in each frequency band for a total of 18.
Satellite radio is available only in the continental United States with a valid SIRIUS subscription. 14. AM/FM: Press to select AM/FM1/FM2 frequency band.
Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from a station, the weaker the signal and the weaker the reception. • T errain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.
CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players.
Unlike AM/FM audible static, you will hear an audio mute when there is a satellite radio signal interference. Y our radio display may display NO SIGNAL to indicate the interference. SIRIUS satellite radio service: SIRIUS Satellite Radio is a continental U.
Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly .
Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel.
HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
3. A. R Rear defroster (if equipped): Press to defrost the rear window . Refer to Rear window defroster (if equipped) later in this chapter for more information. 3. B. Heated mirrors (if equipped): Press to activate/deactivate. This function will clear snow , fog and thin ice from the side rear view mirrors.
Panel ( ) and panel/floor ( ) modes: • Move the temperature control to the coolest setting. • Select A/C and recirculated air ( ). Use recirculated air with A/C to provide colder airflow . • Set the fan to the highest speed initially , then adjust to maintain comfort.
T emperature conversion: T o switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center , refer to Setup menu in the Message center section of the Driver Controls chapter for more information. If your vehicle is equipped with a mini message center , see your authorized dealer for temperature conversion.
4. Recirculation control: Press to activate/deactivate air recirculation in cabin. Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle.
Automatic T emperature Control (A TC) system with heated seats (if equipped) T emperature conversion: T o switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center , refer to Units (Fahrenheit/Celsius) in the Driver Controls chapter .
MAX A/C: For maximum cooling performance, press , A/C, , and set the temperature to 60°F and the highest blower setting. 1. Defrost : Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog and thin ice.
12. A/C control: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency . Engages automatically in AUTO, (defrost) and (floor/defrost). 13. OFF: Outside air is shut out and the fan will not operate.
• T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows.
HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
At this point, the headlamps and park lamps will turn off. Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the , or position and the high beams are not turned on.
Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
3. T urn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover one of the headlamps so no light hits the wall. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right.
INTERIOR LAMPS Map lamps T o turn on the map lamps, press the control next to each lamp. Rear map lamp (if equipped) The rear map lamp lights are located on the end of the overhead rail system. The lamps can be turned on or off by pushing on the lens.
Dome/courtesy lamps (if equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is OFF . The reading portion, the two outer lights, can only be toggled on and off at the lamp.
Function Number of bulbs T rade number Headlamps 2 H13 / 9008 Front park/turn lamps 2 3157A (amber) Front sidemarker 2 194 Foglamps 2 9140 Backup lamp (except Harley) 2 3156 Backup lamp (Harley) 2 315.
5. Remove the bulb by turning it counterclockwise, then pull it straight out. Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
4. Slide the headlamp assembly forward disconnecting the snap attachment at the fender . 5. Remove bulb socket from the lamp assembly by turning it counterclockwise and then pull the bulb straight out. Install the new bulb(s) in reverse order . Replacing tail/brake/turn signal/backup lamp bulbs 1.
Replacing high-mount brake and cargo lamp bulbs Make sure the headlamp control is in the OFF position. 1. Remove the two screws and move the lamp assembly away from the vehicle to expose the bulb sockets. 2. Remove the bulb socket by rotating counterclockwise and pulling it out of the lamp assembly .
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
While holding the steering column, pull the lever up to its original position to lock the steering column. Never adjust the steering column when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps.
OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. The overhead console can come on rails, which can be removed by the customer , or it can come as a non-rail component of the headliner , which cannot be removed.
• When on the overhead rail, adjacent bins must be pinned together . Bins adjacent to the End Cap must be pinned to the End Cap. Bins without pin attachments should not be placed on the overhead rail. Failure to pin the bins together can allow the bins to become separated from the rail under certain conditions.
While pushing upwards with palms, grip the side latches with fingers and squeeze. W ith pressure applied with palms and side latches squeezed down, pull downward on the entire storage bin and remove. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only .
The auxiliary power point is located on the instrument panel. Do not use the power point for operating the cigarette lighter element (if equipped). T o prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W .
When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and hold the bottom part of the rocker switch to open the window . Press and hold the top part of the rocker switch to close the window .
• Press and hold the bottom part of the rocker switch to open window all the way to the full open position. • Press and hold the top part of the rocker switch to close the window . When operating the power sliding back window you must ensure all rear seat occupants and/or cargo are not in the proximity of the back window .
EXTERIOR MIRRORS Power side view mirrors T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror .
Heated outside mirrors (if equipped) Heated mirrors remove ice, mist and fog. T o activate the heated mirrors, press the rear defrost button R located on the climate control panel. Refer to Rear Window Defrost in the Climate Controls chapter for more information.
Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal.
Resuming a set speed Press the RES/RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RES/RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h).
• Depress the brake pedal until the desired vehicle speed is reached, press the SET control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped).
In Satellite Radio mode (if equipped): • Press and release SEEK to advance through preset channels or press and hold SEEK to increment to the next subscribed channel. In CD mode: • Press and release SEEK to select the next track selection on the CD or press and hold SEEK to fast forward in the current track selection.
When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening. Note: The moon roof will open to the “comfort” position first before opening all the way .
When programming your HomeLink 威 W ireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink 威 W ireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.
3. Simultaneously press and hold both the HomeLink 威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents.
Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink 威 to accept the signal from the hand-held transmitter .
Erasing HomeLink 姞 buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink 威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
Usually , when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary . Refer to Compass calibration adjustment.
1. Start the vehicle. 2. T o enter the compass calibration mode, press and hold the button for greater than eight seconds. The display will then show CAL in the display window . 3. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles until CAL indicator turns off.
• A verage Fuel Economy • T rip Elapsed Drive T ime Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter . Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna.
6. Press the RESET , then press SETUP control repeatedly until the correct zone setting for your geographic location is displayed on the message center . The range of zone values are from 01 to 15 and “wraps” back to 01. 7. T o exit the zone setting mode, and to “lock in” your change, press and release the RESET control.
DTE is calculated using a running average fuel economy , which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display . The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.
Setup menu Press this control for the following displays: • System Check • Units (English/Metric) • Autolock • Autolamp Delay • Language System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored.
1. T o disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolocks ON or OFF . Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off.
The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message.
STOP ENGINE SAFEL Y . Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition.
• Engine sensor Contact your authorized dealer as soon as possible if these messages occur on a regular basis. POSITIVE RETENTION FLOOR MA T Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals.
T ailgate removal Y our tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw . Disconnect cable. 3. Disconnect the other cable. 4.
4. Evenly push down on the extender and push the round knobs in on each side locking it in place. Green markings on the shaft indicate the locked position. The locking clip screws below the middle bar can be tightened counterclockwise for extra security .
KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Refer to the SecuriLock 娂 passive anti-theft system section in this chapter for more information.
CHILDPROOF DOOR LOCKS (IF EQUIPPED) • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
Y our vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key . • lock all the vehicle doors without a key .
The (lock) and (unlock) features will work again after: • a door has become ajar , • the ignition is turned to the 3 (ON) position, or • using the UNLOCK control on your remote entry transmitter or unlocking via the keyless entry keypad.
Activating the memory feature T o activate this feature: 1. Position the seat and adjustable pedals to the positions you desire. 2. Press the SET control on the driver’ s seat.
2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery .
T o program the transmitters yourself: Note: Ensure the brake pedal is not depressed during this sequence. • Unlock all doors using the power door lock/unlock control.
The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, even if the dimmer control is on.
4. W ithin five seconds, press the control two times. Note: One horn chirp should be heard, indicating the system has been disabled. Conversely , a horn chirp followed by a honk will indicate the system is enabled. Pressing the power door control two times again will turn the feature ON if it was previously OFF , or OFF if it was previously ON.
Power door unlock/lock procedure Y ou must complete Steps 1–5 within 30 seconds, or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait a minimum of 30 seconds to begin again. 1. T urn the ignition to the 3 (ON) position, then press the control three times.
KEYLESS ENTRY SYSTEM (IF EQUIPPED) Y ou can use the keyless entry keypad to: • lock all vehicle doors. • unlock only the driver’ s door . • unlock all vehicle doors. • program/erase the customer keycode. • enable/disable the autolocking feature.
4. After the code is entered, the locks will cycle, confirming that the new code has been set. T ips: • Do not set a code that uses five of the same number . • Do not use five numbers in sequential order . • The factory set code will work even if you have set your own personal code.
Note: The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Replacement keys If your keys are lost or stolen and you don’t have an extra coded key , you will need to have your vehicle towed to an authorized dealer . The key codes need to be erased from your vehicle and new coded keys will need to be programmed.
5. W ithin 10 seconds of removing the second coded key , insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position (maintain ignition in the 3 (ON) position for at least one second, but no more than ten seconds).
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Push control to lower head restraint. Front seat • Lift the track release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the release lever handle located on the side of the seat up to move the seat back forward or backward.
Using the armrest (if equipped) Push the release control to move the armrest up or down. Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle.
Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor .
Memory seats/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat and adjustable pedals to two programmable positions. The memory seat control is located on the driver’ s seat. • T o program position one, move the driver seat, and adjustable pedals to the desired position.
The head restraints can be moved up and down. Lift the head restraint so that it is located directly or as close as possible behind your head. Push control to lower head restraint. Folding up the rear seats (if equipped ) The rear seat has a split 60/40 cushion.
Returning the seat to seating position Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
How does the Personal Safety System 姟 work? The Personal Safety System 娂 can adapt the deployment strategy of your vehicle’ s safety devices according to crash severity and occupant classification and conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM).
rear -facing child seats, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking.
Front outboard safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’ s forward momentum.
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
2. Insert the belt into the clip on the back panel. Protect the stowed belt if you carry cargo this may damage or soil the belt. If the belt has been disconnected to carry large objects behind the seat, reconnect it as follows: 1. Remove the belt from the stowage clip on the back panel.
Safety belt with cinch tongue (Regular Cab center only) The cinch tongue will slide up and down the belt webbing when the belt is stowed or while putting safety belts on. When the lap/shoulder safety belt is buckled, the cinch tongue will allow the lap portion to be shortened, but pinches the webbing to keep the lap portion from getting longer .
Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoulder belt under the arm.
Shorten and fasten the belt when not in use. Energy management retractors Y our vehicle has a safety belt system equipped with energy management retractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in a controlled manner .
Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt, or the Regular Cab center safety belt.
2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Safety belt pretensioner Y our vehicle is equipped with safety belt buckle pretensioners at the driver and front outboard passenger seating positions. Do NOT place objects between the seats, as this could interfere with the functioning of the pretensioner .
Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and right front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down.
Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts.
BeltMinder 姞 The BeltMinder 威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster when the driver’ s and front passenger’ s safety belt is unbuckled.
If... Then... The driver’ s or front passenger’ s safety belt becomes unbuckled for approximately 1 minute while the vehicle is traveling at least 3 mph (5 km/h) and more than 1-2 minutes have elapsed since the ignition switch has been turned to ON.
Reasons given... Consider ... “T raffic is light” Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly , but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted.
Read Step s1-4t horoughly before proceeding with the deactivation/activation programming procedure. The driver and front passenger BeltMinder 威 features can be deactivated/activated by performing th.
AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) 1. Airbag cover The airbag supplemental restraint system is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries.
Important SRS precautions All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag (SRS) is provided. Always transport children 12 years old and under in the back seat if your vehicle has a back seat.
Do not put anything on or over the airbag cover (1). Placing objects on or over the airbag cover may cause those objects to be thrown by the airbag into your face and torso or may result in a failure of the airbag to inflate properly , both of which could result in serious injury .
Children and airbags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seat than in the front seat.
How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system.
If the airbag has deployed, the airbag will not function again and must be replaced immediately . If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision. Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a tone to indicate the condition of the system.
The front passenger sensing system will disable (will not inflate) the front passenger’ s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat.
• When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front pass.
The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated according to the table below .
SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags.
Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly , which could increase the risk of serious injury in a crash.
T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle.
Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LA TCH and tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter .
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Installing child safety seats in cinch tongue combination lap and shoulder belt seating position (Regular Cab Center seating position Only) If you are using a regular cab center seat, see Center front safety belt (Regular Cab center seating position only) earlier in this chapter for instructions on attaching the mini-buckle.
Rear facing child seats should NEVER be placed in front of an active airbag. 3. Slide the tongue up the webbing. 4. While holding both shoulder and lap portions next to the tongue, route the tongue and webbing through the child seat according to the child seat manufacturer’ s instructions.
6. While pushing down with your knee on the child seat pull up on the shoulder belt portion to tighten the lap belt portion of the combination lap and shoulder belt. 7. Allow the safety belt to retract and remove any slack in the belt to securely tighten the child safety seat in the vehicle.
2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child seat according to the child seat manufacturer’ s instructions. 4. Insert the belt tongue into the proper buckle for the center seating position until you hear a snap and feel it latch.
• F150 Regular Cab • F150 SuperCrew and SuperCab Front seat tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat and under the head restraint. 3. Locate the correct anchor for the selected seating position.
• Front seat Regular Cab center (located on back panel) If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 5. Install the child safety seat tightly using the LA TCH anchors or safety belts.
Rear seat tether strap attachment There are three loops of webbing just above the back of the rear seat (along the bottom edge of the rear window) in the SuperCab and SuperCrew . These loops are to be used as both routing loops and anchor loops for up to three child safety seat tether straps.
3. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 4. T ighten the tether strap according to the child seat manufacturer’ s instructions.
The lower anchors for child seat installation are located at the rear section of the seat between the cushion and seat back. The LA TCH anchors are below the locator buttons on the seat back. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments.
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter .
• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
TIRES T ires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry .
INFLATING Y OUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required.
Maximum Permissible Inflation Pressure is the tire manufacturer’ s maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire.
6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts or bulges.
Age T ires degrade over time, even when they are not being used. It is recommended that tires generally be replaced after 6 years of normal service. Heat caused by hot climates or frequent high loading conditions can accelerate the aging process.
Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally be replaced as a pair . Safety practices Driving habits have a great deal to do with your tire mileage and safety .
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment.
Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry .
8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains.
V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.
transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x 100) = 1400 – 440 – 1200 = – 240 lb. No, you do not have enough cargo capacity to carry that much weight.
T owing a trailer places an additional load on your vehicle’ s engine, transmission, axle, brakes, tires and suspension. Inspect these components carefully periodically during, and after any towing operation. Exceeding the maximum GCWR could result in extensive damage to your vehicle and personal injury .
Regular Cab 4x2 (144.5” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.2L (with manual transmission) 3.31 7200 (3266) 2300 (1043) 3.55 8500 (3856) 3600 (1633) 4.2L (with automatic transmission) 3.55 10000 (4536) 5100 (2313) 3.
Regular Cab 4x4 (144.5” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 3.55 11700 (5307) 6200 (2812) 4.6L 3.73 12200 (5534) 6700 (3039) 5.4L (with 17” tires) 3.55 14000 (6350) 8300 (3765) 5.4L (with 18” or 20” tires) 3.
SuperCab 4x2 (144.5” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L (with 17” tires) 3.55 11700 (5307) 6400 (2903) 4.6L (with 18” tires) 3.55 11200 (5081) 5900 (2677) 4.6L (with 17” tires) 3.73 12200 (5534) 6900 (3130) 4.
SuperCab 4x4 (132.5” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L (with 17” tires) 3.55 11500 (5216) 6000 (2721) 4.6L (with 18” tires) 3.55 11000 (4990) 5500 (2494) 4.6L (with 17” tires) 3.73 12000 (5443) 6500 (2948) 4.
SuperCab 4x4 (144.5” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 5.4L (with 18” or 20” tires) 3.55 13500 (6123) 7800 (3538) 5.4L (with 17” tires) 3.73 15000 (6804) 9300 (4218) 5.4L (with 18” or 20” tires) 3.
Crew Cab 4x2 (138.5” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 5.4L (with 17” tires) 3.55 14000 (6350) 8500 (3856) 5.4L (with 18” or 20” tires) 3.55 13500 (6123) 8000 (3629) 5.4L (with 17” tires) 3.
Crew Cab 4x2 (150.5” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L (with 18” or 20” tires) 3.55 11200 (5080) 5700 (2585) 4.6L (with 17” tires) 3.73 12200 (5534) 6700 (3039) 4.6L (with 18” or 20” tires) 3.
T railer frontal area considerations: • Not to exceed towing vehicle frontal area without Class IV trailer towing package • Not to exceed 60 square feet (5.52 square meters) with Class IV trailer towing package Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle.
T railer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’ s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’ s hydraulic brake system directly to your vehicle’ s brake system.
Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance Information for more information. T railer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination.
Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water .
V ehicles equipped with automatic transmission and 4x4 vehicles equipped with an electronic-shift transfer case: • Release the parking brake. • T urn the key in the ignition to the OFF position. • Place the transmission in N (Neutral). • Do not exceed a distance of 50 miles (80 km).
STARTING Positions of the ignition 1. OFF/LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. Note: The ignition key cannot be removed from the ignition unless the gearshift lever is securely latched in P (Park).
Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately .
• Make sure the parking brake is set. If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor 3. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate.
Starting the engine 1. T urn the key to 3 (ON) without turning the key to 4 (ST ART). If there is difficulty in turning the key , rotate the steering wheel until the key turns freely . 2. T urn the key to 4 (ST ART), then release the key as soon as the engine starts.
If the engine fails to start using the preceding instructions (flexible fuel vehicles only) 1. Press and hold down the accelerator 1/3 to 1/2 way to floor , then crank the engine. 2. When the engine starts, release the key , then gradually release the accelerator pedal as the engine speeds up.
Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light. Base instrument cluster with and without tachometer Mid and Luxury instrument cluster Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS).
Base instrument cluster with and without tachometer Mid and Luxury instrument cluster Parking brake T o set the parking brake (1), press the parking brake pedal down until the pedal stops. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released.
T RACTION CONTROL 姟 (IF EQUIPPED) Y our vehicle may be equipped with a T raction Control 娂 system. This system helps you maintain the stability and steerability of your vehicle, especially on slippery road surfaces such as snow- or ice-covered roads and gravel roads.
STEERING T o help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump reservoir fluid level (below the MIN mark on the reservoir).
PREPARING TO DRIVE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Y our vehicle has larger tires and increased ground clearance, giving the vehicle a higher center of gravity than a passenger car .
2. Locate the round access plug on the underside of the steering column cover . 3. Remove the access plug using a flat head screwdriver , then push the override button using a flat head screwdriver , apply the brake pedal and shift the transmission into N (Neutral).
If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, turn the ignition to LOCK, then remove the key . 2. Open the center console bin. Using a screwdriver , carefully pry off the console finish panel surrounding the shifter mechanism by inserting a screwdriver into the latch slot as shown.
If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer .
T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
• Floor -shift transmission The transmission control indicator (TCIL) will illuminate on the instrument cluster . Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive.
• Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor .
During each shift, the clutch pedal must be fully depressed to the floor . Failure to fully depress the clutch pedal to the floor may cause increased shift efforts, prematurely wear transmission components or damage the transmission.
Maximum downshift speeds 1 4 - 3 45 mph (72 km/h) 17 mph (27 km/h) 3 - 2 35 mph (56 km/h) 13 mph (21 km/h) 2 - 1 20 mph (32 km/h) 7 mph (11 km/h) 1 Downshift at lower speeds when driving on slippery surfaces. Reverse 1. Make sure that your vehicle is at a complete stop before you shift into R (Reverse).
T o help avoid personal injury , always use caution when in reverse and when using the RSS. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle.
The RSS automatically turns on when the gearshift lever is placed in R (Reverse) and the ignition is ON. An RSS control allows the driver to turn the RSS on and off. T o turn the RSS off, the ignition must be ON, and the gear selector in R (Reverse). An indicator light on the control will illuminate when the system is turned off.
• 4X4 LOW – Momentarily illuminates when the engine is started. Illuminates when 4L is selected. Using a manual 4WD system (if equipped) 2H (2WD High) – Power to the rear wheels only; used for street and highway driving. Provides optimal smoothness and fuel economy at high speeds.
3. Place the transmission in N (Neutral). 4. Move the transfer case lever through N (Neutral) directly to the desired position. • If the transfer case will not engage into 4L (4WD Low), allow the vehicle to coast at a speed below 3 mph (5 km/h), then repeat Steps 2 through 4.
4L (4WD Low) - Uses extra gearing to provide maximum power to all four wheels at reduced speeds. Intended only for off-road applications such as deep sand, steep grades or pulling heavy objects. 4L (4WD Low) will not engage while the vehicle is moving above 3 mph (5 km/h); this is normal and should be no reason for concern.
A WD (Auto) - Power delivered to all four wheels, as required, for increased traction. This is appropriate for all on-road driving conditions, such as dry road surfaces, wet pavement, snow , gravel and shallow sand. 4H (Lock) - The “4X4 HI” light will illuminate in the instrument cluster when this position is selected.
Basic operating principles • Do not use 4WD on dry , hard surfaced roads. Doing so will produce excessive noise, increase tire wear and may damage drive components. 4WD modes are only intended for consistently slippery or loose surfaces. • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle.
Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. Do not spin the wheels at over 35 mph (56 km/h).
Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly .
Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall.
Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. A void driving crosswise or turning on steep slopes or hills .
Driving on snow and ice 4WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
• Rear ballast weight behind the rear axle may be required to prevent exceeding the FGA WR, and provide front-to-rear weight balance for proper braking and steering. • Front wheel toe may require re-adjustment to prevent premature uneven tire wear .
Do not attempt to service, repair , or modify the air bag supplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer . Transmission operation while plowing • Shift transfer case to 4L (4WD Low) when plowing in small areas at speeds below 5 mph (8 km/h).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement .
HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash.
This switch is located in the front passenger’ s footwell, behind the kick panel access cover , to the left of the fuse box. The access cover needs to be removed to reset the fuel pump shut-off switch. T o reset the switch: 1. T urn the ignition OFF .
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 10A* Run/Accessory - Wipers, Instrument cluster , Audio for XL/STX 2 20A* Stop/T urn lamps, Brake on/off switch 3 7.5A* Power mirrors, Memory seats and pedals 4 10A* DVD battery power , Power fold mirror 5 7.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 9 20A* Fuel pump relay , Fuel injectors, Intake manifold runner control (4.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 25 10A* LH low beam headlamp 26 20A* Horn relay (PCB3), Horn power 27 5A* Passenger Air bag Deactivation (P AD) warning.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 101 30A** Starter solenoid 102 20A** Ignition switch feed 103 20A** ABS valves 104 — Not used 105 30A** Electric trai.
Auxiliary relay box The relay box is located in the engine compartment on the left fender . • W ith Daytime Running Lamp (DRL) and 4x4 options • W ithout Daytime Running Lamp (DRL) and 4x4 options.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. The use of tire sealants may damage your tires.
Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Groun.
Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: T ool Location Spare tire Under the vehicle, just forward of the rear bumper Jack,.
Tire change procedure T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
7. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park).
8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered.
3. T urn the jack handle clockwise until the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when the tire is raised to the maximum tightness.
JUMP STARTING The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your vehicle.
Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . Ford recommends your vehicle be towed with a wheel lift or flatbed.
GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, o.
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program.
The CAMV AP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.
If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office.
(Items in this catalog may be purchased by credit card, check or money order .) Obtaining a French owner ’ s guide French Owner’ s Guides can be obtained from your authorized dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
W AXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product.
ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.
• 4.6L engine • 5.4L engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer .
• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause.
Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. • Be certain to wash or wipe your hands clean if y.
Dash & Vinyl Cleaner (ZC-38-A), then dried with a clean, dry cloth. When cleaning the low gloss areas: • Do not use paper towels or newspaper . • Do not use silicone or T eflon-based products.
• T o clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11–A). Dry the area with a soft cloth. • T o help maintain its resiliency and color , use the Motorcraft Deluxe Leather Care Kit (ZC-11–D), available from your authorized dealer .
Scratches Natural Markings - Because the leather in the seat comes from genuine steer hides, there will be evidence of naturally occurring markings, such as small scars. These markings give character to the seating covers and should be considered as proof of a genuine leather product.
Motorcraft Car W ash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.
SERVICE RECOMMENDATIONS T o help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
2. Block the wheels. T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engine 1. Battery 2. Clutch fluid reservoir (manual transmission) 3. Power steering fluid reservoir 4. Brake fluid reservoir 5. Engine coolant reservoir 6. Air filter assembly 7. Engine oil filler cap 8.
4.6L V8 1. Battery 2. T ransmission fluid dipstick (automatic transmission) 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6.
5.4L V8 1. Battery 2. T ransmission fluid dipstick (automatic transmission) 3. Air filter assembly 4. Power steering fluid reservoir 5. Engine oil dipstick 6.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
Poor wiper quality can be improved by cleaning the wiper blades and the windshield, refer to Windows and wiper blades in the Cleaning chapter . T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers.
• 4.2L V6 engine • 4.6L/5.4L V8 engine 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again.
.
4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until three clicks are heard or until the cap is fully seated. T o avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced.
Battery posts, terminals and related accessories contain lead and lead compounds. W ash hands after handling. Because your vehicle’ s engine is also electronically controlled by a computer , some control conditions are maintained by power from the battery .
ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water , which equates to a freeze point of -34°F (-36°C).
• Refer to scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter . If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty .
• A large amount of water without engine coolant may be added, in case of emergency , to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible.
Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary , add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level.
If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration above 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage.
When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase.
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin.
Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable. If your vehicle is not serviced in accordance with flexible fuel vehicles procedures, damage may occur and your warranty may be invalidated. When refueling always shut the engine off and never allow sparks or open flames near the filler neck.
Fuel Filler Cap Y our fuel tank filler cap has an indexed design with a 1/4 turn on/off feature. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap counterclockwise 1/4 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe.
If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury .
Octane recommendations Do not be concerned if your engine sometimes knocks lightly . However , if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage.
FFV engine (if equipped) Y our FFV will operate well on ordinary “Regular” unleaded gasoline, but only the highest quality fuel ethanol will provide the same level of protection and performance. T o identify if your vehicle is an FFV , check your VIN or the label on the inside of your fuel filler door .
The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty .
Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel economy under current driving conditions. Additionally , keeping records during summer and winter will show how temperature impacts fuel economy .
Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.
• A void running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in scheduled maintenance information performed according to the specified schedule.
On board diagnostics (OBD-II) Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD-II). This OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance information for the service interval schedules. If adding fluid is necessary , use MERCON 威 AT F .
Use only a DOT 3 brake fluid designed to meet Ford specifications. Refer to Lubricant specifications in this chapter . Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists.
Automatic transmission fluid expands when warmed. T o obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 20 miles [30 km]).
The transmission fluid should be in this range if at normal operating temperature (150°F-170°F [66°C-77°C]). The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]). High fluid level Fluid levels above the safe range may result in transmission failure.
An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.
3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use only fluid that meets Ford specifications. Refer to the Lubricant specifications section in this chapter .
3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Lubricant specifications section in this chapter . DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Y our vehicle may be equipped with universal joints that require lubrication.
Changing the air filter element • 4.2L/4.6L engines 1. Loosen the clamp that secures the air filter element in place. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the open end of the air filter housing.
2. Pull air filter tray assembly out toward front of vehicle and lift air filter element up and out of housing. The air filter box needs to be free of any debris before installing a new air filter . 3. Install a new air filter element into the tray assembly .
For PCV valve replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part.
Fluid Ford Part Name Application Capacity Engine oil (includes filter change) 8 Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) 4.2L engine 6.0 quarts (5.7L) 4.6L engine 6.0 quarts (5.
Fluid Ford Part Name Application Capacity Rear axle 5 Motorcraft SAE 75W -140 Rear Axle Lubricant (synthetic) 8.8/9.75 inch axle 5.5 pints (2.6L) 6 10.25 inch axle 6.9 pints (3.3L) 7 W indshield washer fluid Motorcraft Premium W indshield W asher Concentrate All 4.
5 Y our vehicle’ s rear axle is filled with a synthetic rear axle lubricant and is considered lubricated for life. These lubricants do not need to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water .
Item Ford part name or equivalent Ford part number Ford specification Brake fluid and clutch fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1 or PM-1-C ESA-M6C25-A or WSS-M6C62-.
Item Ford part name or equivalent Ford part number Ford specification T ransmission /steering/parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) Premium Long-Life Grease XG-.
MERCON 威 and MERCON 威 V type fluids are not interchangeable. DO NOT mix MERCON 威 and MERCON 威 V . Use of a transmission fluid that indicates dual usage (MERCON 威 and MERCON 威 V) in an automatic transmission application requiring MERCON 威 may cause transmission damage.
V EHICLE DIMENSIONS Regular Cab V ehicle dimensions Styleside 6.5’ box - inches (mm) Flareside 6.5’ box - inches (mm) Styleside 8.0’ box - inches (mm) (1) Overall length 211.2 (5364) 211.2 (5364) 229.8 (5837) (2) Overall width 78.9 (2005) 78.9 (2005) 78.
SuperCab V ehicle dimensions Styleside 5.5’ box - inches (mm) Styleside / Flareside 6.5’ box - inches (mm) Styleside 8.0’ box - inches (mm) (1) Overall length 217.8 (5532) 229.8 (5837) 248.4 (6309) (2) Overall width 78.9 (2005) 78.9 (2005) 78.9 (2005) (3) Overall height – 4x2/4x4 74.
Super Crew V ehicle dimensions Styleside 5.5’ box - inches (mm) Styleside 6.5’ box - inches (mm) (1) Overall length 223.8 (5685) 235.8 (5990) (2) Overall width 78.9 (2005) 78.9 (2005) (3) Overall height – 4x2/4x4 73.5 (1867) / 76.0 (1931) 73.5 (1867) / 76.
Super Crew V ehicle dimensions Styleside 5.5’ box - inches (mm) Styleside 6.5’ box - inches (mm) (4) Wheelbase 138.5 (3518) 150.5 (3823 ) (5) T rack - Front 67.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6.
GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer .
Lifestyle Bedliners and bedmats Cargo organization and management Rear seat entertainment systems T owing mirrors T railer hitches, wiring harnesses and accessories Peace of mind Mobile-Ease 娂 hands.
A Accessory delay ..........................74 Air cleaner filter ............... 309–311 Air conditioning ....................50, 53 Airbag supplemental restraint system ................................ 138–139 and child safety seats ............
washing .................................... 263 waxing ..................................... 264 wheels ...................................... 264 wiper blades ............................ 267 Climate control (see Air conditioning or Heating) .......
starting after a collision .........235 Engine block heater ................. 204 Engine oil .................................. 279 checking and adding .............. 279 dipstick .................................... 279 filter , specifications ......
Illuminated visor mirror .............68 Infant seats (see Safety seats) 151 Inspection/maintenance (I/M) testing ........................................302 Instrument panel cleaning ................................... 267 cluster ...................
Parts (see Motorcraft parts) .... 311 Passenger Occupant Classification Sensor ................. 120 Power distribution box (see Fuses) ...............................237 Power door locks ........................98 Power mirrors ......................
utility-type vehicles .................... 8 Specification chart, lubricants ...........................315, 318 Speed control .............................. 77 Starting a flex fuel vehicle .......203 Starting your vehicle ........................ 200–201, 203 jump starting .
333.
334.
335.
デバイスFord F-150 (2006)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ford F-150 (2006)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFord F-150 (2006)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ford F-150 (2006)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ford F-150 (2006)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ford F-150 (2006)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFord F-150 (2006)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ford F-150 (2006)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFord F-150 (2006)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
