AlpineメーカーSPX-137Aの使用説明書/サービス説明書
ページ先へ移動 of 20
SPX-177A / SPX-137A Component 2-way Speaker System OWNER’S MANUAL Please read before using this equipment MANUEL DE L'UTILISA TEUR V euillez lire le présent manuel avant la mise en service du matériel. ALPINE ELECTRONICS, INC. T okyo office ; 1-1-8 Nishi Gotanda, Shinagawa-ku, T okyo 141-8501, Japan T el.
2 Attention UTILISER LES ACCESSOIRES SPECIFIES ET LES INST ALLER CORRECTEMENT . L’utilisation d’autres pièces non désignées risque de provoquer des dommages à l’intérieur de l’appareil ou son installa- tion risque de ne pas être faite correctement, et les pièces desserrées peuvent provoquer des dangers.
3 19. Fixed-flush mount cup / Embase fixe à niveau …………………… x2 20. Mounting clip / Attache de montage .....…………………………. x4 21. Swivel-spacer / Swivel-spacer .....………… ………………. x4 22. Screw st4.2x9.
4 T abel of Contents Installation W oofer (SPX-177A)..................................................................... 5 W oofer (SPX-137A)..................................................................... 7 T weeter ............................
5 Installation (SPX-177A) W oofer: Surface mount W oofer: Factory/stealth Notes: l Attach gasket tape as shown. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm Notes: l Attach gasket tape as shown.
6 Installation (SPX-177A) W oofer: Factory/OEM custom fit Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break away any unused tabs.
7 Installation (SPX-137A) W oofer: Surface mount Notes: l Attach gasket tape as shown, then lock speaker into grille ring. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm W oofer: Factory/stealth Notes: l Attach gasket tape as shown.
8 Installation T weeter: Swivel-surface mount st4.2x19mm Fig. 1 Fig. 2 Fig. 3 Notes: l Before mounting, insert swivel retention cup into housing. Then rotate until achieving a positive lock using an appropriate tool (screwdriver , etc.). l Mount complete swivel-surface cup and fix swivel spacer to base.
9 Installation T weeter: Swivel-flush mount Fig. 1 Fig. 2 Fig. 3 Notes: l Before mounting, insert swivel retention cup into housing. Then rotate until achieving a positive lock using an appropriate tool (screwdriver , etc.). l Insert complete swivel-flush cup with mounting clips first through opening.
10 Installation T weeter: Fixed-flush mount Fig. 1 Fig. 2 Fig. 3 Notes: l Insert fixed-flush cup with mounting clips first through opening. (Fig. 1) l Press mounting clips at center and secure with screw . (Fig. 2) l Make connections, then insert and lock tweeter into cup.
11 Installation T weeter: Surface-angle mount Notes: l Remove network cover , and mount as shown l Connect wires to terminal blocks accordingly . (see System Connection Diagrams section) l Make appropriate jumper settings using jumper puller tool (see Crossover Network Settings section) l Re-secure network cover .
12 System Connections Single Input Bi-wire Input Note: Signal link jumpers highlighted in black must be inserted for proper function of single input configuration. Wiring for connection of crossover network to amplifier is not included. Caution: These jumpers must be removed when using b-wire input.
13 Crossover Network Settings It is common knowledge that the automotive environment poses numerous acoustic challenges to achieving high-fidelity sound. Fortunately , many of these problems can be overcome with proper speaker placement, equalization, digital time correction, or other techniques.
14 Crossover Network Settings System T ype 1 (default) Speaker Placement Description: In this system type, woofer and tweeter are mounted in close proximity to each other , and are mounted in essentially the same plane.
15 Crossover Network Settings System T ype 1 Filter Description: In this setting, the woof er and tweeter are at appro ximately equal distance from the listener . Using the kic k-panel for placement is only one of man y locations av ailable to mount both drivers together .
16 Crossover Network Settings System T ype 2 Speaker Placement Description: In this system type, woofer and tweeter are mounted different locations and at dif ferent distances from the listener . Also of significance, is the fact that the tweeter is the nearest driver .
17 Crossover Network Settings System T ype 2 Filter Description: In this system type, the woofer is in a dif ferent plane from the tweeter , making it necessary to use the phase correction sections of the network to compensate for the different relative positions.
18.
19 Specifications Specifications System SPX-177A SPX-137A T ype Component 2-wa y speak er Component 2-w ay speak er P ower Handling (peak/RMS) 240/60 W 200/50 W Impedance 4 W 4 W F requency Response 35-35 kHz 35-35 kHz Net W eight 5 kg 4.5 kg Drivers General Speaker siz e 6.
Designed by Alpine Electronics of America, Inc. Printed in Denmark by T eam L ynderup.
デバイスAlpine SPX-137Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Alpine SPX-137Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAlpine SPX-137Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Alpine SPX-137Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Alpine SPX-137Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Alpine SPX-137Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAlpine SPX-137Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Alpine SPX-137Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAlpine SPX-137Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。