Frymasterメーカー8196606の使用説明書/サービス説明書
ページ先へ移動 of 24
Frymaster, a member of the Co mmercial Food Equipm ent Serv ice Association, recommends using CFES A Certified Tec hnicians. *8196606* 24-Hour Service Hotline 1-800-551-8633 Price: $6.
NOTICE IF, DURING THE WARRANTY PERIOD, THE CUS TOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID.
Table of Contents Theory of Operation 1-1 Service/Software Procedures 2-1 Troubleshooting 3-1 Illustrated Parts List 4-1 Wiring Diagrams 5-1.
Cabinet Service Procedures 1-1 1 Functional Description 1.2 Theory of Operation The cabinet operates on 208-250VAC 50 or 60 cycle si ngle-phase power. The main switch activates a relay, which supplies line voltage to two distri bution boards, three cooling fans and a power supply.
Cabinet Service Procedures 1-2 1.3 Start Up Indicators and Test Points Upon startup, the cabinet beeps. LED’s on the dist ribution boards flash. The displays show the version number of the cabinet’s firm ware and then the row’s status. Distribution boards shown with ribbon cables removed.
Cabinet Service Procedures 2-1 2 Service Procedures DANGER: Failure to disconnect po wer from the unit be fore servicing could result in serious injury or death.
Cabinet Service Procedures 2-2 Update: Boa r ds 1. Turn power off. 2. Insert flash drive in USB port located on cabinet bezel. 3. Turn power on. 4. Cabinet displays version numbers followed by current menu setting. 5. Press programming key. 6. Screen scroll s Enter Acce ss S equence.
Cabinet Service Procedures 2-3 USB . 6. Press OK. 7. The master control displays Please Wait … as f iles are transferred to the f lash drive, changing to the number of files copi ed when the process is complete. 8. Press OK. 9. Remove flash drive. 10.
Cabinet Service Procedures 2-4 2.2 Placing the cabinet in Service Mode The cabinet can be put in service mode, a diagnostic settings which allows the heater plates to be controlled individu ally, brightness settings on the displays adjusted an d re-addressing for unique arrangements of bezels.
Cabinet Service Procedures 2-5 Readdressing the Cabinet Addressing, or assigning a position-specific component such as a display or dis tribution board, is done automatically by the cabinet on startup. Co mmunication errors can o ccur on start-up after a board installation however.
Cabinet Service Procedures 2-6 2.3 Accessing the Electronic Components 1. The component shelf is accessed by rem oving two screws on each side of the unit ( Fig. 1 ). 2. Lift and remove the sides, which expos es screws that hold the top in place ( Fig.
Cabinet Service Procedures 2-7 • ERR LED toggles when a communicati on error is detected; it’s not unusual to see a flash, but regular flashing means communications problem s. • LED5 and LED6 used for programming/debugging; have no diagnostic function.
Cabinet Service Procedures 2-8 suspect heater. Note: Line voltage is onl y seen when the row is calling for heat. 2. Check for line voltage between the power input terminal and the terminal block. 3. Check for +5VDC at the power-in terminal and the term inal block for the power supply.
Cabinet Service Procedures 2-9 Fig. 7: Two screws (see arrows) at the base of each side of the cabinet secure the sides. 3. HHHH means RTD indicates the temperature is a bove 255°F (124°C), but below "Open" circuit resistance, which causes SENS ALARM .
Cabinet Service Procedures 2-10 2.6. 1 Removing/Replacing a Distribution Board or Communication Board 1. Remove power. 2. Remove and mark the wires on the faulty component. 3. Remove the board by lifting it from its standoffs. 4. Position the new board and attach wires.
Cabinet Service Procedures 2-11 9. Slide the row assembly completely into th e cabinet and return the spacers between the heater plates. Ensure the row is evenly positioned in the cabinet. There must be sufficient space to allow the bezel tabs to fit b etween the outside row plate and the cabinet interior wall.
Cabinet Troubleshooting 3-1 The master control display and the row displays show error messages when there is a problem . The messages are shown in the matrix below along with possible causes a nd diagnostic tests.
Cabinet Troubleshooting 3-2 Failure modes not accompanied by a master contro l display are shown below with possible causes and tests. Symptom Possible Causes Tests Unit fails to power up; fans don’t run. • No power to cord. • Blown 20 amp fuse.
Cabinet Parts 4-1 Parts Lists, Exploded Views Item Part Number Description 1 108-1897 Top Cap 2 823-7636 Rear Fascia 3 807-4882 Circuit Breaker, 16 amp 4 807-5111 Time/Temperature switch 5 807-4911 Po.
Cabinet Parts 4-2 Item Part Number Description 8 807-5111 Time/Temperature switch 9 826-2781 Bezel, with boards, front with short ribbon cable * 826-2782 Bezel with boards, rear, with long ri bbon cab.
Cabinet Parts 4-3 Item Part Number Description * 807-4952 LON board, international 18 807-4868 Power Supply 19 807-3490 Power relay 20 406-0011 UHC-HD Single Filter Board * Ribbon Cables * 807-4916 Ti.
Cabinet Wiring Diagrams 5-1 Wiring Diagram, Delta Power, L1-L2.
Cabinet Wiring Diagrams 5-2 UHC-HD, WYE Power, L1-N.
Frymaster, L.L.C., 8700 Line Av enue, Shrev eport, Louisiana 71106 TEL 1-318-865-1711 FAX (Parts) 1-318- 219-7140 FAX (Tech Support) 1-318-219-7135 PRINTED IN THE UNITED STATES SERVICE HOTLINE 1-800-551-8633 Price: $6.
デバイスFrymaster 8196606の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Frymaster 8196606をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFrymaster 8196606の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Frymaster 8196606の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Frymaster 8196606で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Frymaster 8196606を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFrymaster 8196606の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Frymaster 8196606に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFrymaster 8196606デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。