FrymasterメーカーFOOTPRINT E4の使用説明書/サービス説明書
ページ先へ移動 of 88
Frymaster, a member of the Co mmercial Food Equipm ent Service Ass ociation, recomm ends usin g CFESA Certified Technicians. 24-Hour Service Hotline 1-800-551-8633 MAY 2009 www.
i NOTICE IF, DURING THE WARRANTY PERIOD, TH E CUSTOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED D IRECTLY FROM FRYMASTER DEAN , OR ANY O F ITS AUTHORIZED SERVICE CEN TERS, AND/OR THE PART BEING U SED IS MODIFIED FR OM ITS ORIGINAL C ONFIGURATI ON, THIS WAR RANTY WIL L BE VOID.
ii DANGER Adequate means must be provided to limit the movement of this appliance without depending on or transmitting stress to the electrical conduit. A restraint kit is provided with the fryer. If the restraint kit is missing contact your local Frymaster Factory Authorized Service Center (FASC) for part number 826-0900.
iii RE SERIES E 4 ELECTRIC FRYERS TABLE OF CONTENTS CAUTIONARY STATEMENTS ........................................................................................................ i ELECTRICAL POWER SP ECIFICATIONS .....................................
iv RE SERIES E 4 ELECTRIC FRYERS TABLE OF CONTENTS cont. 2.4.3 Drain Valves and Associated Parts (U nits without Built-In Filtration) ........... 2-15 2.5 Electronics and Elect rical Components .........................................................
1-1 RE SERIES E 4 ELECTRIC FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 General Before performing any maintenance on your Frym aster fryer, disconnect the fr yer from the electrical power supply. When electrical wires are disconnected, it is recommende d that they be marked in such a way as to facilitate re-assembly.
1-2 3. Remove the two screws from the upper corners of the contr ol panel and allow the control panel to swing down. 4. Unplug the wiring harness from the 15-pin connector on the interface b oard and disconnect the grounding wire from terminal adjacent to the 15- pin connector on th e back of the controller.
1-3 1.4 Replacing a High-Limit Thermostat 1. Remove the filter pan and lid f rom the unit. Drain the fryp ots into a Shortening Disposal Unit (SDU) or other appropri ate metal co ntainer. DANGER DO NOT drain more than one full frypot or two split frypots into the SDU at one time.
1-4 2. Disconnect the fryer from the electrical power s upply and reposition it to gain access to the rear of the fryer. 3. Remove the four screws from both sides of the lower back panel. Then remove the two screws on both the left and right sides of the back of the tilt housing.
1-5 10. Secure any loose wires with wire ties making sure tha t the lead wires will not interfere with th e movement of the springs. Rotate the elements up and down making sure that m ovement is not restricted and that the wires are not pinched.
1-6 from the lift springs. Also ensure that the wi re sleeving extends into the tube as sembly to prevent the edge of the tube assembly from chafi ng the wires. Press the pins into the connector in accordance with the diagram on the following pa ge, and then close the connector to lock the leads in place.
1-7 2. Disconnect the fryer from the electrical power supply. 3. Remove the two screws securing the cover of th e contactor box. The cont actor boxes above the filter pan are accessed by sliding under the fryer. They are located to the left and right above the guide rails (see photo below).
1-8 3. Slide the metal bezel up to release the bottom ta bs, then slide the beze l down to disengage the upper tabs. 4. Remove the two screws from the upper corners of the control panels a nd allow them to swing down (see illustration and photo on page 1-1).
1-9 22. Position the elem ent tube assembly in the f ry pot and reinstall the m achine screws and nuts removed in step 14. 23. Reconnect the oil return flexlines to the frypot , and rep lace aluminum tape, if necessary, to secure heater strips to the flexlines.
1-10 If the pump starts af ter resetting the therm al overloa d switch, then som ething is causing the motor to overheat. A major cause of overheating is when se veral frypots are filtered sequentially, overheating the pump and motor. Allow the pump m otor to cool at least 30 minutes before resuming operation.
1-11 DANGER DO NOT drain more than one full frypot or two split frypots into the SDU at one time. 2. Disconnect the fryer from the electrical power su pply and repo sition it to gain access to both the front and rear.
1-12 10. Reconnect the unit to the electrical power suppl y, and verify that the pump is functioning correctly (i.e., when a filter handle is placed in the ON position, the motor should start and there should be strong suction at the intake f itting and outflow at th e rear flush port.
1-13 100-120V C onfi gurati on 208-250V C onfi gurati on Timing circuitry in the controller initiates and stops basket lift operation depending upon the variables programmed by the opera tor. W hen the product button is pressed, the timing circuitry activates a coil in the basket lif t relay to supply power to the lo wer microswitch.
1-14 MOTOR AND GEAR PROBLEMS With the modular basket lift, the most likely problem to be encounter ed in this category is erratic motion of the lift due to a worn drive gear. Fa ilure to keep the lift rod and bushings properly lubricated will cause unnecessary w ear of the gear.
1-15 1.11 Interface Boar d Diagnostic Chart The following diagram and charts provide ten quick system checks that can be perform ed using only a multim eter.
1-16 1.12 Probe Resistance Chart Probe Resistance Chart For use with fryers manufactured with Minco Thermistor probes only. F OHMS C F OHMS C F OHMS C F OHMS C F OHMS C 60 1059 16 130 1204 54 200 1350.
1-17 1.13 Wiring Diagrams 1.13.1.1 Modular Basket Lift Wiring Diagram 208-250V.
1-18 1.13.1.2 Modular Basket Lift Wiring Diagram 100-120V.
1-19 1.13.2 Component Wiring 1.13.2.1 Standard Fryers.
1-20 1.13.2.2 Component Wiring- Fr yer and Half.
1-21 1.13.3 Tilt Switch Wiring Standard Fryer and half.
1-22 1.13.4 Component Wiring - Fast Ready.
1-23 1.13.5 Fast Read y Computer Wiring.
1-24 1.13.6 Computer Harness - Fast Ready.
1-25 1.13.7 Control Wiring - Fast Ready.
1-26 1.13.8 Contactor – DELTA Configuration MERCURY CONTROLS CIRCUIT 14kW / 17kW EPRI/TRIAC SSR ELEMENT / CONTROL WIRING 22kW EPRI/TRIAC SSR ELEMENT / CONTROL WIRING HIGH VOLTAGE TO COMPONENT BOX ME.
1-27 1.13.8 Contactor – DE LTA Configuration cont. 22kW Single Phase SSR Wiring.
1-28 1.13.9 Contactor Box - WYE Configuration Export.
1-29 1.13.10 Terminal Block Wiring.
1-30 1.13.11 Oil Disposal Wiring.
1-31 1.13.12 Simplified RE14/17/22 Series – Full Vat Wiring ELECTRIC RE14/17/22 SERIES - F ULL-VAT L3 24V HIGH LIMIT DRAIN SAFETY SWITCH 3 PHASE POWER TERMINALS GND 12 J2 11 10 2 1 6 9 J2-8 J2-7 J3 .
1-32 1.13.13 Simplified RE14/17/22 Series – Dual Vat Wiring.
1-33 1.13.14 Simplified RE14/17/22 Series – Full Vat Wiring (EXPORT) WYE ELECTRIC RE14/17/22 SERIES - FULL-VAT EXPORT 24V HIGH LIMIT DRAIN SAFETY SWITCH 12 J2 11 10 2 1 6 9 J2-8 J2-7 J3 J3 2 2 13 13.
1-34 1.13.15 Simplified RE14/17/22 Series – Du al Vat Wiring (EXPORT) WYE.
1-35 1.13.16 Simplified RE14/17/22 Series – Full Vat Wiring EPRI.
1-36 1.13.17 Simplified RE14/17/22 Series – Fu ll Vat Wiring EPRI (EXPORT) WYE.
2-1 RE SERIES E 4 ELECTRIC FRYERS CHAPTER 2: PARTS LIST 2.1 Accessories 3 4 5 6 7 8 9 10 11 1 2 ITEM PART # COMPONENT 1 809-0171 Thumbscrew, ¼ -20 X 1 ⅜ -inch 2 810-2793 Hanger, Wireform Basket (us.
2-2 2.2 Basket Lift Assembly and Associated Parts 28 26 25 1 27 22 21 10 2 16 11 17 5 4 17 17 24 3 20 3 14 18 12 9 8 17 15 29 30 33 34 35 32 31.
2-3 2.2 Basket Lift Assembly and Associated Parts cont. ITEM PART # COMPONENT 106-1805SP Basket Lift Asse mbly, 200-220VAC w/Relay (Items 1-23) 1 810-1012 Rod, Basket Lift 2 813-0035 Bushing, Bronze 3 807-2513 Capacitor, 12.
2-4 2.3 Cabinetry 2.3.1 Back Panels, Control Panel Frames, Doors, Sides, Tilt Housings, and Top Caps 1 2 3 4 5 20 21 18 19 17 16 15 14 13 6L 12 11 8 10 9 6R 7.
2-5 2.3.1 Back Panels, Control Panel Frames, Doors, Sides, Tilt Housings & Top Caps cont. ITEM PART # COMPONENT 1 Back Panel, U pper (Panel f or five stati on fryer show n) 220-0421 Single Station.
2-6 2.3.1 Back Panels, Control Panel Frames, Doors, Sides, Tilt Housings & Top Caps cont. ITEM PART # COMPONENT 16 106-4067 Pin Assembly, Doo r * 810-0275 Spring, Door Pin * 809-0970 Retaining Rin.
2-7 2.3.2 Cabinets, Bases, Braces, and Associated Parts The 5-Station cabinet illu stra ted is typical of most RE Series Electric cabinets. All compon ents used in RE Series cabinets ar e identified, but not all components are used in every configuration.
2-8 2.3.2 Cabinets, Bases, Braces, and Associated Parts cont. ITEM PART # COMPONE NT 1 106-3828 Upright Assembly , Left 2 106-3829 Upright Assem bly, Right 3 200-1651 Support, Cross Cabinet (use 220-1.
2-9 2.4 Drain System Components 2.4.1 Drain Tube Sections and Associated Parts See next section for Drain Valves.
2-10 2.4.1 Euro-Look Drain Tube Secti ons and Associated Parts cont. ITEM PART# COMPONENT 1 Drain Tube, Left/Right End Short 823-4625 Full-Vat 823-4624 Dual-Vat 823-5943 Fryer ½, RH ½ Fryer 823-6003.
2-11 2.4.2 Drain Valves and Associated Pa rts (Units with Bu ilt-In Filtration) 1 2 3 4 5 6 7 8 9 10 11 12 Single Footprint Fu ll-Vat Drain Valve Assembly 106-6300 2.
2-12 2.4.2 Drain V a l v e s and A ss oc ia te d Part s (U ni ts with Built-In Fi ltr at ion ) cont 1 2 3 6 5 7 9 8 10 11 13 12 Compression Washers Full-Vat Drain Valve Assembly 106-3760 / Fryer ½ 106-7004 4 2.4.2 Drain V a l v e s and A ss oc ia te d Part s (U ni ts with Built-In Fi ltr at ion ) cont.
2-13 2.4.2 Drain V a l v e s and A ss oc ia te d Part s (U ni ts with Built-In Fi ltr at ion ) cont..
2-14 2.4.2 Drain V a l v e s and A ss oc . Parts (U ni ts with Built-In Fi ltr at ion ) cont. ITEM P A R T # COMPONENT 1 816-0639 Cap, Drain Handle 2 809-0539 Nut, ⅜ -16 2-Way Hex Lock 3 900-2934 Re.
2-15 2.4.3 Drain Valves and Associated Part s (Units without Bu ilt-In Filtration) 1 2 3 4 5 ITEM PART # COMPONENT 1 810-1569 Valve, 1.25-inch Non-Filter Full-Vat Drain 2 806-7915SP Valve, 1-inch Non-Filter Dual-Vat Left Drain 3 806-7916SP Valve, 1-inch Non-Filter Dual-Vat Right Drain 4 812-1226 Drain Extension, 1.
2-16 2.5 Electronics and Wiring Components 2.5.1 Component Boxes.
2-17 2.5.1 Component Boxes cont. ITEM PART # COMPONENT 1 106-5592 Box Asse mbly, Component Standard 106-6747 Box Asse mbly, Component Fryer ½ 2 200-3300 Bracket, Component Box Strain Relief 3 806-949.
2-18 2.5.2 Contactor Boxes 2.5.2.1 Left and Right Over the Filter Pa n Contactor Box Configurations.
2-19 2.5.2.1 Left and Right Over the Filter Pan Contactor Box Configurations cont. NOTES: Left and right contactor box assemblies are mirror images of one another. With the exception of the box itself, most components of a left-hand assem bly are the same as those in the corresponding right-hand assembly and vice versa.
2-20 2.5.2.2 Large Center Contactor Box Configurati ons (Non-Filter, Not over the Filter and Single Units).
2-21 2.5.2.2 Large Center Cont actor Box Configurations (Non- Filter, Not Over the Filter and Single Units) cont. I T E M PART # COMPONENT 1 106-6081 Box Assembly, Contactor (Non-Filter or Not Over th.
2-22 2.5.3 Fuse Boxes 3 1 2 4 5 7 6 8 10 9 11 12 Left 22kW and Single Phase Fuse Box Assembly 106-5505/106-6678 Right 22kW and Single Phase Fuse Box Assembly 106-5506/106-6679 ITEM PART # COMPONENT 1 .
2-23 2.5.4 Terminal Blocks ITEM PART # COMPONENT 1 823-5631 Box, LH Rear Terminal Block 2 823-5632 Box, RH Rear Terminal Block 823-5797 Box, Single Station Fryer Only (see previous page for cover 222-.
2-24 2.5.5 Heating Element Assemblies and Associated Parts 2.5.5.1 Element Assemblies and Hardware NOTE: These elements apply onl y to the RE series fryers.
2-25 2.5.5.1 Heating Element Assemb lies and Associated Parts cont. ITEM PART # COMPONENT 1 Element Kits – includes gaskets, grommets, t ie wraps, screws and nuts. 826-2198 200V 1 7.0 kW (also used for 220V 8.5 kW) 826-2201 200V 1 8.5 kW 826-2208 200V 11.
2-26 2.5.5.2 Element Tube Assemblies.
2-27 2.5.5.2 Element Tube Assemblies cont. ITEM PART # COMPONENT 1 106-7653SP Tube Assem bly RE Element, Full-Vat 106-6736 Tube Assembly RE Element Fryer ½ LH Half Fryer ( use 106-6061 RH Half Fryer).
2-28 2.5.6 Controllers cont. ITEM PART # COMPONENT 3 Basket Lift Timer 826-2330 Full-Vat (CE) 106-4366 Dual-Vat (CE) 826-2401 Full-Vat (Non-CE) 826-2402 Dual-Vat (Non-CE) 4 Solid-State (Analog) Controller 826-2538 Full-Vat 106-4334 Dual-Vat * 802-2021 Graphic Sheet of Sym bols 2.
2-29 2.5.7.2 Contactor Box Wiring Assemblies – 12-Pin Full-Vat C-1 ITEM PART # COMPONENT 106-6031SP Contactor Box Harness Assembly Full Vat 1 Standard (See wiring diagrams on pages 1-19.) EPRI (uses harness above plus wire kits WIR0733 and WIR0736) (See wiring diagrams on pages 1-26 and 1-27.
2-30 2.5.7.3 Contactor Box Wiring Assemblies – 6-Pin (Left Element) 1 2 BLUE BLACK 1 2 3 4 5 6 BLACK BLACK BLUE BLUE BLUE BLACK 1 2 3 4 5 6 BLACK BLACK BLUE BLUE ITEM PART # COMPONENT 1 106-6768 14/17 kW Standard Mercury 106-7849 22 kW Triac SSR 2 106-6771 14/17 kW Mechanical Contactor 106-7851 22 kW Mercury and High Amp Mechanical Contactor 2.
2-31 2.5.7.5 Main Wiring Harn esses - Full and Dual Vat USED ONLY ON DUAL VAT HARNESSES J4 C1 C6 C6 C1 J4 J4 C1 C6 FULL VAT HARNESS 807-4194 DUAL VAT HARNESS 807-4195 12-Pin Female Connector 807-0159 .
2-32 2.5.7.5 Main Wiring Harnesses – Fryer and ½ FRYER AND ½ HARNESS 807-4364.
2-33 2.5.7.6 Component Box, Filter Pump and Basket Lift Wiring Harnesses 1 2 4 3 ITEM PART # COMPONENT 1 106-5750 Full Vat Control Harness J4 to J2 (Standard) 106-6639 Full Vat Control Harness J4 to J.
2-34 2.5.7.7 Component Box to Filter Pump Harness 2.5.7.8 B asket Lift Harness 2.5.7.9 Interface Board to C ontroller Wiring Harness – 15-Pin.
2-35 2.6 Filtration System Components.
2-36 2.6 Filtration System Components cont. I T E M PART # COMPONENT * 826-1979 Filter Pan Roller Kit (four each of Items 7 and 8) * 826-1980 Service Filter Pan (Item 5 minus Item 2) * 826-1981 Service Filter Pan A s s e m b l y (Se rvi ce Filter Pan above plus Items 3 and 4) √ * 826-1392 O-Ring (Pkg.
2-37 2.6 Filtration System Components cont. I T E M PART # COMPONENT 14 200-4408 Rail, Left Pan Filter Multi-Vat Fryers 106-5981 Support Assembly, Left Single Station Fryer Only 220-1378 Support, Left.
2-38 2.7 Frypot Assemblies and Associated Parts.
2-39 2.7 Frypot Assemblies and Associated Parts cont. I T E M PART # COMPONENT 1 Frypot Assembly (does not include Item 6) 2 823-5545SP F r ypot, Full-Vat Filter with Insulati on (for use on EPRI unit.
2-40 2.8 Oil Return System Components 6 4 5 3 9 8 7 10 1 11 12 18 19 20 21 22 Typical Rear-Flush Oil Return Plumbing Full-vat rear-flush plumbing is shown on the left side of the oil return manifold; dual-vat plumbing is shown on the right side.
2-41 2.8 Oil Return System Components cont. ITEM PART # COMPONENT 1 106-5596 Handle Assembly, Fu ll- Vat an d Ri gh t D ua l- Vat Rea r F lus h C om ple te 106-6410 Handle Assembly, Full-Vat Deep Cabi.
2-42 2.9 Oil Disposal Plumbing.
2-43 2.9 Oil Disposal Plumbing cont. ITEM PART # COMPONENT 106-5959 Plumbing, Front Oil Disposal 106-5933 Plumbing, Rear Oil Disposal 1 106-6033 Valve Assembly, Oil Disposal 2 220-0922 Rod, Oil Dispos.
2-44 2.11 Wiring Connectors and Pin Connectors ITEM PART # COMPONENT 1 807-1068 2-Pin Female 2 807-0158 6-Pin Female 3 807-0156 9-Pin Female 4 807-0159 12-Pin Female 5 807-0875 15-Pin Female 6 807-1067 2-Pin Male 7 807-0157 6-Pin Male 8 807-0155 9-Pin Male 9 807-0160 12-Pin Male 10 807-0804 15-Pin Male 11 826-1341 Term inal, Fema le Split Pin (pkg.
2-45 2.12 Fasteners ITEM PART # COMPONENT * 809-0429 Bolt, ¼-inch – 20 x 2.00-inch Hex Head ZP Tap * 809-0514 Capscrew, 5/16-inch-18 NC Hex * 809-0448 Clip, Tinnerman * 826-1366 Nut, 4-40 Keps Hex (Pkg. of 25) (809-0237) * 826-1358 Nut, 6-32 Keps Hex (Pkg.
THIS PAGE INTENTIONALLY LEFT BLANK.
Frymaster, L.L.C., 8700 Line Av enue, Shrev eport, Louisiana 71106 TEL 1-318-865-1711 FAX (Parts) 1-31 8-219 -7140 (Tech Support) 1-318-219-7135 819-6150 PRINTED IN THE UNITED STATES SERVICE HOTLINE 1.
デバイスFrymaster FOOTPRINT E4の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Frymaster FOOTPRINT E4をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFrymaster FOOTPRINT E4の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Frymaster FOOTPRINT E4の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Frymaster FOOTPRINT E4で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Frymaster FOOTPRINT E4を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFrymaster FOOTPRINT E4の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Frymaster FOOTPRINT E4に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFrymaster FOOTPRINT E4デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
