FSP/FortronメーカーKnight KN-1103TS Towerの使用説明書/サービス説明書
ページ先へ移動 of 18
1K/2K/3K Online UPS Uninterruptible P ower Supply S ystem User Manual.
T able of Contents 1. Importa nt Safety W arning ............................................................................................... 1 1-1. T ra nsportation ..................................................................................
1 1. Importan t Safety Warnin g Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and r ead carefully the following instructions before installing the unit. Do not operate this unit bef ore reading through all safety information and operating instructions carefully 1-1.
2 1-5. Maintenance, service and faults The UPS system operates wit h hazardous voltages. Repa irs may be carried out only by qualified maintenance personnel.
3 2. Installation and setup NOTE: Before installation, please inspect t he unit. Be sure that nothing inside the package is damaged. Please keep t he original package in a saf e place for f uture use. NOTE: There a re two diff erent t ypes of online UPS: standa rd a nd long-run mod els.
4 8. Output circuit break e r 9. Output terminal 2-2. Setup the UPS Step 1: UPS input connection Plug the UPS into a two-pole, three -wire, grounded recept a cle only . Avoid using extension cords. The power cord is supplied in t he UPS packag e. Step 2: UPS output connection For socket -type outputs, simply connect devices to the ou tlets .
5 Step 5: Install software For optimal computer system protection, install UPS monitoring software t o fully configure UPS shutdown. Y ou may insert provided CD into CD-ROM to install the monitoring software. If not, please follow steps b elow to download and install monitoring software from the internet: 1.
6 3. Operations 3-1. Button operation Button Function ON/Mute Button Turn on the UPS: Pre ss and hold ON/Mute button for at least 2 secon ds to turn on the UPS. Mute the a larm: When the UPS is on ba ttery mod e, press and hold this button for at least 5 seconds to disa ble or e nable the alarm system.
7 Display Function Remaining backup time information Indicates the remaining backup time in pie chart. Indicates th e remaining ba ckup time in numbers. H: hours, M: minute, S: se cond Fault information Indicates that the warning and fault occurs. Indicates the warning and fault codes, a nd the codes are listed in details in 3-5 section.
8 3-3. Audible Alarm Battery Mode Sounding every 4 seconds Low Battery Sounding every second Overload Sounding twice every second Fault Continuously sounding Bypass Mode Sounding every 10 seconds 3-4.
9 the following output voltage: 10 0: presents output voltage is 100Vac 110: presents output volta ge is 110Vac 115: presents output voltage is 115Vac 120: presents output voltage is 120Vac 127: presents output voltage is 127Vac 02: Frequency Converter enable /disable Interface Setting Parameter 2 & 3: Ena ble or disable converter mode.
10 06: Bypass enable/disable when UPS is off Interface Setting Parameter 3: Enable or disable Bypass function. You may choose the following two options: ENA: Bypass enable DIS: Bypass disable .
11 3-6. Operating Mode Description Operating mode Description LCD display Online mode When the input voltage is within acceptable range, UPS will provide pure and stable AC power to output.
12 3-8. Warning indicator W arning Icon ( flashing) Alarm Low Battery Sounding every second Overload Sounding twice every second Battery is not connected Sounding every second Over Charge Sounding eve.
13 4. Troubleshoo ting If the UPS s ystem does not oper ate correctly , please solve the problem by using the table below. Symptom Possible cause Remedy No indication and alarm even though the mains is normal. The AC input power is not connected well.
14 Symptom Possible cause Remedy Battery backup time is shorter th an nominal v alue Batteries are not f ully charged Charge the bat teries for at least 5 hours and then check capacity . If the problem still persists, consult your dealer . Batteries defect Contact your dealer to replace the batt ery .
15 5. Storage and M aintenance Operation The UPS system contains no user -serviceable parts. If the battery s ervice life (3~5 years at 25° C ambient temperature) has been exceeded, the batteries mus t be replaced. In this case , please contact your dealer.
16 6. Specifications CAPACITY* 1000 VA / 800 W 2000 VA / 1600 W 3000 VA / 2400 W INPUT Voltage Range Low Line Transfer 160VAC/140VAC/120VAC /110VAC± 5% ( based on load percentage 100% - 80 % / 80 % -.
デバイスFSP/Fortron Knight KN-1103TS Towerの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
FSP/Fortron Knight KN-1103TS Towerをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFSP/Fortron Knight KN-1103TS Towerの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。FSP/Fortron Knight KN-1103TS Towerの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。FSP/Fortron Knight KN-1103TS Towerで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
FSP/Fortron Knight KN-1103TS Towerを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFSP/Fortron Knight KN-1103TS Towerの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、FSP/Fortron Knight KN-1103TS Towerに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFSP/Fortron Knight KN-1103TS Towerデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。