FujitsuメーカーP3PC-1932-01ENの使用説明書/サービス説明書
ページ先へ移動 of 28
P3PC-1932-01EN fi-5530C2 Ima g e Scanner.
.
fi-5530C2 Image Scanner Getting Started i CONTENTS ■ Regulatory Informatio n .......................... .............................. ii ■ Note of Liability ......... ........................................................... iii ■ Safety Precautions .
ii INTRODUCTION Thank you for purchasing the fi-553 0C2 Duplex Color Scanner. This document describ es how to use fi-5530C2 and basic operation methods.
fi-5530C2 Image Scanner Getting Started iii ■ Note of Liability READ ALL OF THIS MANUAL CAREFULL Y BEFORE USING THIS PRODUCT . IF THIS PRODUCT IS NOT USED CORRECTL Y , UNEXPECTED INJUR Y MA Y BE CAUSED T O USERS OR BYST ANDERS. Also, keep this manual in a safe place so that it can be easily referred to during use of this product.
iv Where there is no distinction between the different versions of the above operating system, the general term "W indows " is used. All the descriptions in this manual assume the usage of Adobe Acro bat bundled with this product. However , Adobe Acrobat may be upgraded without n otice.
fi-5530C2 Image Scanner Getting Started v ■ Safety Precautions Do not damage the AC cable. Use only specified AC cables and connector cables Use this scanner only at the indicated power volt age. Do not connect to multiple- power strip s. Do not touch the AC cable with wet hands.
vi Do not install the scanner on unst able surfaces. Do not block the ventilation ports. Do not place heavy object s or st and on top of the scanner . Firmly insert the power plug. A void any contact when scanner is in use. Do not use the scanne r immediately after moving it from a cold place into a warm room.
fi-5530C2 Image Scanner Getting Started 1 Chapter1 PREP ARING THE SCANNER 1.1 Checking the Contents of the Scanner Package When you unpack the scanner package, make su re that the packa ge contains a ll the pa rts on the list included in the package .
2 1.3 Operator panel The operator panel is located on the right side of the scanner. The panel co nsists of a Function Number Dis- play, four buttons and a LED. . *) About the settings on the launcher, refer to FUJITSU TWAIN32 scanner driver h elp and "fi-5530C2 Oper- ator’s Guide" on the Setup CD-ROM.
fi-5530C2 Image Scanner Getting Started 3 Chapter2 INST ALLA TION OF THE SCANNER 2.1 Installing the Scanner 1. Place the scanner at its installation site. For details on the scanner's dimensions and required installation space, refer to section 7.
4 2. Connect the other end of the USB interface cable to your personal computer. ■ Connecting with the SCSI Inter- face Cable When using the scanner with a SCSI interface, the fol- lowing SCSI interface cable and SCSI card must be pur- chased.
fi-5530C2 Image Scanner Getting Started 5 2.3 Installing the Scanner Software To scan documents with this scanner, you must install a scanner driver for operating the scanner as well as scanning software (hereinaft er called the "application") for launching the driver and performing a scan.
6 3. If the scanner is automatically detected, [Found New Hardware Wizard] or [Add/ Remove Hardware Wizard] dialog box will appear. Click the [Cancel] button to close the Wizard dialog box. 4. Insert the Setup CD-ROM into the CD drive. ⇒ <SETUP DISK START UP SCREEN> appears.
fi-5530C2 Image Scanner Getting Started 7 The installation of FUJITSU TWAIN 32 is complete. Next, install ScandAll PRO (-> page 8). FUJITSU ISIS Scanner Driver FUJITSU ISIS is an ISIS-c ompliant scanner driver. To use this scanner with any ISIS-compatible application, install FUJITSU ISIS, following the proce- dure below.
8 5. Click [INSTALL PRODUCTS], and then click [ISIS Driver]. 6. Error Recovery Guide Installation dialog box appears. Error Recovery Guide is an application with which you can view on-screen information for troubleshooting errors that may occur in the scanner.
fi-5530C2 Image Scanner Getting Started 9 4. Proceed with the installation, following the on - screen instructions. 5. When the [InstallShield Wizard Complete] dia- log box appears, click the [Finish] button.
10 Adobe ® Acrobat ® Install Adobe Acrobat from the "Adobe Acrobat CD- ROM" provided with this scanner. 1. Insert the Adobe Acrobat CD-ROM into the CD-ROM drive. ⇒ The [Adobe Acrobat] dialog box appears. 2. In the dialog box below, click the folder icon; installation starts and the Setup dialog box appears.
fi-5530C2 Image Scanner Getting Started 11 2.4 Checking Scanner Driver Operat ion This section explains how to check the operation of the installed scanner driver by using ScandAll PRO. Make sure that the scanner dr iver is installed properly, following the procedure below.
12 9. In the [Scan Settings] dialog box, clear the [Save to file] checkbox. 10. Click [Scanner Settings]. ⇒ A setup dialog box appears for you to config- ure scanner driver settings. 11. Configure scanner settings such a s the resolu- tion and paper size.
fi-5530C2 Image Scanner Getting Started 13 2.5 Uninstalling Supplied Programs The following explains how to uninstall software appli- cations provided with the scanner. 1. Start your personal computer. 2. Exit all applications. 3. From the [Start] menu, select [Control Panel] -> [Add or remove Programs].
AP-1 Appendix1 TROUBLESHOOTING ■ Troubleshooting checklist Symptom Check this item Remedy The scanner is not turned on. Have you pushed the power button? Push the power button. Are the AC cable and AC adapter prop- erly connected to the scanner? Correctly connect the AC cable and the AC adapter.
fi-5530C Image Scanner Getting Started AP-2 Paper is n ot fed (p ick error occurs frequently, or docu- ment stops midway). Do the documents satisfy the "Docu- ment Quality" and the "Mul.
AP-3 ■ Temporary error The following shows the proced ure for releasing of each temporary error. • "U1" error 1. Remove jammed documents. (For details, refer to section 5.1 "Removing Jammed Documents" of "fi-5530C2 Opera - tor’s Guide on the Setup CD-ROM.
fi-5530C Image Scanner Getting Started AP-4 Appendix2 DAIL Y CARE ■ Cleaning Materials For details about the cleaning materials, contact the FUJITSU scanner dealer where you purchased the scan- ner. ■ Cleaning Method The ADF must be cleaned with a lint-free cloth moist- ened with the Cleaner F1.
AP-5 Appendix3 REPLACING CONSUMABLES ■ Consumables and Replacement Cycle The followings are the speci fications of consumables and their recommended replacement cycles. To purchase consumables, contact the store where you purchased the scanne r or an authorized FUJITSU scanner service provid er.
fi-5530C Image Scanner Getting Started AP-6.
z Copying of the contents of this manual in whole or in part and copying of the scanner applicat ion is prohibited under the copyright la w. z The contents of this manual are subject to change without notice.
デバイスFujitsu P3PC-1932-01ENの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Fujitsu P3PC-1932-01ENをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu P3PC-1932-01ENの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu P3PC-1932-01ENの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu P3PC-1932-01ENで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu P3PC-1932-01ENを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu P3PC-1932-01ENの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu P3PC-1932-01ENに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu P3PC-1932-01ENデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。