FujitsuメーカーScanPartner 620Cの使用説明書/サービス説明書
ページ先へ移動 of 26
ScanPartner 620C Image Scanner User's Manual (Doc. No. 250-0062-0 Ver. 1.0).
ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
iii Table of Contents 1. INTRODUCTION ........................................................................................... 1-1 2. INSTALLATION ............................................................................................ 2-1 2.1 SHIPPING BRACKET .
1-1 1. INTRODUCTION Congratulations on your purchase of Fujitsu ScanPartner 620C Scanner. Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you with the proper instructions on how to unpack, install, operate and maintain the Scanner.
2-1 2. INSTALLATION Please unpack the Scanner carefully, and check the contents against the c hecklist. If any items are missing or damaged, please contact your authorized local dealer immediately. Precautions • Keep the Scanner out of direct sunlight.
2-2 Figure 2-1 Removing the Shipping Bracket Figure 2-2 Securing the Shipping Bracket “Use Position” “Shipping Position”.
2-3 2. 1 .2 REFITTING THE SHIPPING BRACKET Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket to avoid causing damage to the Scanners’ internal mechanism. Please follow the instructions below to refit the shipping bracket.
2-4 Figure 2-3 Adjusting the SCSI ID setting. SCSI ID Selector SCSI Termination Switch On Off.
2-5 2. 3 ADF PAPER CHUTE i). Raise the right side of the paper chute to about 45 degrees. ii). Pull down the wire leg from under the paper chute . iii). Insert the wire leg into the grips on the document cover . iv). Pull out the paper chute extension to the length you want.
2-6 2. 4 ADF OUTPUT TRAY i). Hold the output paper tray some 30 degrees aslant as shown in Figure 2-5. ii). Insert the three protrusions on the output paper tray to the three slots on the ADF. iii). Release the paper tray gently. Make sure the tray is firmly attached to the ADF.
2-7 2. 5 DOCUMENT LOADING For flatbed scanning Documents that can not be scanned using the ADF can be placed on the flatbed for scanning. (See Figure 2-6) i). Place the document to be scanned onto the document glass face down. ii). Position the document so that the upper-right corner is aligned with the reference mark .
2-8 2. 6 ADF SCANNING Standard paper size can be scanned automatically using the ADF. Refer to Figure 2-7. i). To prevent occasional paper jam when automatically feeding multiple documents, fan the paper before loading.
2-9 2. 7 CONNECTING THE CABLE i). Turning the Power Off Depress the side marked “O” to turn the power off. Connect the power cable and SCSI signal cable as shown in Figure 2-8 and Figure 2-9. ii). Turning the Power On Depress the side marked “I” to turn the power on.
2-10 Figure 2-8 ScanPartner 620C Power Cable Connection Figure 2-9 ScanPartner 620C SCSI Cable Connection SCSI Cable Connector Power Cable To PC SCSI Port Power Switch SCSI Port.
3-1 3. MAINTENANCE 3. 1 CLEANING THE ADF Your Scanner is designed to be maintenance free. However, it still needs to be cleaned occasionally to ensure optimum image quality and performance. From time to time the pad assembly and feeding rollers may become contaminated with ink, toner particles or paper dust.
3-2 Figure 3-1 Opening the ADF unit and Document Cover Feeding Roller ADF Pad Module ¬ ¬ - -.
3-3 3. 2 CLEANING THE GLASS The procedures: i). Soak a cotton swab with some isoprophy alcohol (95%). ii). Open the ADF unit and document cover as shown in Figure 6-2. Wipe the glass of flatbed area and ADF area by moving the swab from side to side. iii).
3-4 3. 3 REPLACING THE ADF SNAP-IN PAD MODULE After scanning approximately 150,000 pages through the ADF, the pad spring may be worn out and you may experience problems with document feeding. In this case, it is highly recommended to replace the pad module with a new one.
3-5 Assembling Procedure 1. Take out the ADF pad module from the box. 2. Hold the upper part of the pad clamp and place it gently to the pad holder as shown in Figure 3-4.
4-1 4. TROUBLESHOOTING The Scanner will automatically perform a simple self-test each time it is turned on. This will help spot major system errors in the Scanner itself. When the test is initiated, the READY LED is flashing. When the test is completed, if no error occur, the READY LED is steadily on.
4-2 Question: Paper becomes skewed in the Scanner. Answer: a) Check the feeding roller condition; do the cleaning if necessary. (See Section 3.1) b) Use the paper guide when feeding the p aper. Question: When I power on the Scanner, it makes noises and will not stand ready.
4-3 Question: While scanning, the Scanner often makes noises, or it scans back and forth. Answer: Please choose lower speed from the TWAIN user interface for low speed PC. Question: The scanned image always comes out to be too dark. Answer: a) Use your application to modify the Gamma setting to 2.
4-4 Figure 4-2 ADF Paper Jam - Removing the Paper ADF Paper Chute Document ADF Unit.
5-1 5. SPECIFICATIONS All specifications are subject to change without notice. The following can not be properly fed by ADF: • Paper with clip or staple attached; • Paper with ink not totally dry;.
5-2 5. 1 SCANPARTNER 620C SPECIFICATIONS Scanner Type v 1-pass colour v Flatbed with ADF built-in Scanning Mode v 36-bit colour v 12-bit Grey Scale v Line Art/Halftone v Error Diffusion (single bit) O.
a Index A ADF cover · 4-3 ADF Scanning · 2-8 B balance wire · 2-8 C Cleaning the ADF · 3-1 Cleaning the Glass · 3-3 Connecting the Cable · 2-9 D document cover · 2-5 Document Loading · 2-7 O o.
デバイスFujitsu ScanPartner 620Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Fujitsu ScanPartner 620Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFujitsu ScanPartner 620Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Fujitsu ScanPartner 620Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Fujitsu ScanPartner 620Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Fujitsu ScanPartner 620Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFujitsu ScanPartner 620Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Fujitsu ScanPartner 620Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFujitsu ScanPartner 620Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
