FurunoメーカーFA-30の使用説明書/サービス説明書
ページ先へ移動 of 30
www .furuno.co.jp.
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : MAY 2007 Printed in Japan All rights reserved.
i IMPORT ANT NOTICES • The descriptions in this manual are intended f or readers with a solid knowl edge of English. • No part o f this manual may be copied or reproduced without written per mission. • If this manu al is lost or worn, cont act your de aler about re placement.
ii WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.
iii CAUTION Observe the following compass safe distances to prevent interference to a magnetic compass: Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. Do not install the equipment where it may get wet from rain or water splash.
iv T ABLE OF CONTENTS FOREWORD ............... ........................ ........................ .................................... ...... v SYSTEM CONFIGURA TION ........................... ........................ ........................ ..... vi 1.
v FOREWORD A W ord to the Owner of the F A-30 Congratulat ions on your choi ce of the FURUNO FA- 30 AIS Receiver. We a re confi- dent you wil l see why the FURUNO name has become syn onymous with quality an d relia bility . For over 50 years FURUNO Elect ric Company has en joyed an envi able reputation for quality marin e electronics equipment.
vi SYSTEM CONFIGURA TION AIS RECEIVER F A-30 HUB WHIP ANTENNA SENSOR OR 12-24 VDC IF-1500AIS OR FR-8xx2 SERIES GPS SPEED LOG GYROCOMP ASS SA TELLITE COMP ASS NA VNET RAD AR CHAR T PLOTTER ECDIS PILO T.
1 1. INST ALLA TION 1.1 Equip ment Li st s Standard su pply Opti onal su pply Name T ype Code No . Qty Remarks AIS R eceiver F A-30 - 1 Inst allation Materia ls CP05-1 1 101 001-014 -160 1 set T apping screw (4x20, 4 pcs.) AIS V iewer FP05- 05910 000-010 -938 1 set F AISPC -MX for PC S pare Part s SP05-05 701 001-014 -150 1 set 2A fuse, 2 pcs.
2 1.2 AIS Receiv er F A -30 Mounti ng cons idera tions, mounti ng The FA-30 ca n be mounted on a desktop, deck or o n a bulkhead. When sel ecting a mounting locat ion, keep the following point s in mind: • The temperature and humidity should be moderate and stable.
3 1.3 Whip Ante nna Location The locat ion of the AIS VHF- antenna should be car efully consider ed. Digital c om mu- nicati on is more sensitiv e than analog/voice communicati on to interference cr eated by reflect ions i n obst ructi ons lik e masts a nd booms.
4 1.4 Wi ring Connect power source, LAN cable, VHF antenna and gr ound wire as shown below. *1 Supply from br eaker on switchboar d. *2 If COM lines (connecti on for NavNet, sensor) are not used, tape them to prevent s hort circui t. VHF WHIP ANTENNA (option) RED BLACK PC, HUB, NAVNET GROUND COAXIAL CABLE 5D-2V (local supply) GROUND WIRE IV-1.
5 Attaching coaxial conn ector (M-P-5) to coaxial cable The antenna cable (coaxial cable, type 5D-2V) is terminated at the FA-30 with an M-P-5 coaxi al connector. At tach the connecto r to the cabl e as shown below. Connecti on of AIS viewer (F AISPC-MX) The AIS vie wer may be connected t o the FA-30 directl y, or to both FA-30 and NavNet vx2.
6 2. WEB SOFTW ARE SETUP , DA T A DISPLA YS 2.1 AIS Receiv er F A -30 The FA-30 has no power switch. Power is fed from the shi p’s switchboard, and a pow- er switch on the switchboard turns the FA-30 on or off. When powered, the PW R LED (green ) on the cover l ights.
7 2.2 COM Port Setup, Network Setup The FA-30 is set up fr om the PC or external displ ay. The procedure below shows how to set up the COM/POWER and NETWORK ports from a PC. NOTICE: Only one FA-30 may be connected to the network. Start up 1. Start up the PC and enter I P address and sub net mask.
8 COM port setup 5. Click COM POR T Setup to show t he COM Port Setup m enu. 6. The default sett ing for Data T ype is IEC61 162, which is suit able for most inst alla- tions. If change is necessary , click t he Data T ype drop-down l ist and choose dat a type as a pplicable, among t he following choices.
9 NETWORK setup 9. Click Net work Setup to show t he Network Setup menu. 10.Enter the I P address assi gned to the F A-30. 1 1.Enter subnet mask for the network. 12.Enter gate w ay address . 13.For NavNet connec tion, en ter Na vNet port number at NavNet Port Number .
10 2.3 Own V essel D at a Disp lay , Chann el Selecti on The Own Vessel Data display shows your ship ’s MM SI no., RX channel nos., and channel sel ection method. 1. Show the main menu, referring to section 2.2. 2. Click Own V essel Data. Description o f own v essel data MMSI: MMSI number (nine-digit number).
11 5. Click the RX Mode drop-down li st to choose which channel (s) to receive. RX 1+2: Rec eive via channels 1 and 2. RX 1: Receive via channel 1. RX 2: Receive via channel 2. 6. Click t he Channel Selectio n drop-down li st. 7. Choose Manual. 8. Click t he OK button to finish.
12 2.4 Sensor St atu s The sensor sta t us display provi des inform ation about se nsors connected t o the FA-30. 1. Show the main menu, referring to section 2.2. 2. Click Sensor S tatus . The illus tration below shows typical sensor sta tus indications.
13 3. MAINTENANCE, TROUBLESHOOTING 3.1 Ma inten ance Regular mainten ance helps maintain good performance. Check the items li sted below at least monthly to hel p keep your equipment in good working or der. Maintenance t able Item Check p oint, remedy Wirin g Check that ea ch cable and wi re are securely fastened.
14 3.2 Replacing the Fuse The fuse (2A) i nside the FA-30 prote cts it from ov ercurrent and equipment fault. If the unit cannot be powered, that is, the P WR (power) LED i s off, the fuse may have bl own. If this happens, turn off the power to the FA-30, open the cover and check t he fuse.
15 3.4 Dia gnostics The built-in diagnost ic facility display s program version no. and checks RAM, ROM and RX channel s for proper oper ation. 1. Open Intern et Explorer a nd show the main menu. 2. Click T est to show the T est di splay . The program versio n number appears on the first lin e.
AP- 1 VHF CHANNEL LIST Ch No. Frequ ency Ch No. Frequency Ch No. Freque ncy Ch No. Frequenc y 1001 156.05 1088 157.4 25 277 156.887 5 2079 161.57 5 1002 156.1 1201 156.0 625 1278 156. 9375 2080 161. 625 1003 156.15 1202 156.1 125 1279 156.987 5 2081 161.
FURUNO FA-30 SP-1 E444 3S01A SPECIFICA TIONS OF A IS RECEIVER F A-30 1. GENERAL 1.1 Rx Capacit y 2250 reports/ minute, 1 channe l 4500 reports/ minute, 2 channels 1.2 Rx Syste m TDMA du al w ave simulta n eous reception 1.3 Frequency Sw it c hing Auto mat ic (external dev ic e) 1.
FURUNO FA-30 SP-2 E444 3S01A 3. INTERF A C E 3.1 COM port Input: RS 422(38.4kbps)/IEC 611 62-1(4800 bps) Output: RS422 (38.4kbps) Input s e nt e nces: ACK, ACA , DTM, GBS , GGA, GLL, GN S, HDT , OSD, RMC , VBW , VTG, DSC , DSE, AIQ, Z DA, PFE C, ABM*, BBM*, AIR* Out pu t sen ten ces: ACA, ACS , ALR, VDM , VD O, T XT, ABK* , PFEC 3.
D-1.
Nov.28'03 D-2.
NAME TYPE 名称 kg DRAWN CHECKED APPROVED DWG.No. SCALE MASS 34 2 1 C B A COM/POWER DC_M(-) DC_P(+) J12 1 2 J7 0V 1 2 3 4 5 COM_TD-A COM_TD-B COM_RD-A COM_RD-B FA-30 AIS RECEIVER AIS受信機 (+) (-).
FURUNO ELECTRIC CO., LTD. 9-52 Ashihara-Cho, Nishinomiya City, 662-8580, Hyogo, Japan Tel: +81 798-65-2111 Fax: +81 798-65-4200 Pub NO. DOC-929 Declaration of Conformity We FURUNO ELECTRIC CO.
デバイスFuruno FA-30の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Furuno FA-30をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFuruno FA-30の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Furuno FA-30の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Furuno FA-30で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Furuno FA-30を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFuruno FA-30の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Furuno FA-30に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFuruno FA-30デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
