FurunoメーカーGP-1610CFの使用説明書/サービス説明書
ページ先へ移動 of 112
.
C 9-52, A shi hara- cho, Ni shinom i ya, J apan T el ephone: 0798-65-21 1 1 T el efax: 0798- 65-4200 Y our Local Agent /Dealer A ll rig hts res erved .
SAFETY INSTRUCTIONS Safety Instructions for the Operator Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Turn off the power immediately if water leaks into the equipment or the equip- ment is emitting smoke or fire.
Safety Instructions for the Installer Do not work inside the equipment unless totally familiar with electrical circuits. Hazardous voltage which can shock, burn or cause serious injury exists inside the equip- ment. Turn off the power at the mains switchboard before beginning the installation.
i FOREWORD A W ord to GP-1610CF Owners ................. iv Features ....................................................... v System Configuration ................................ vi INST ALLA TION 1.1 Equipment Lists ............................. 1-1 1.
ii W A YPOINTS, ROUTES 7.1 Entering W aypoints ....................... 7-1 7.2 Erasing Individual W aypoints ....... 7-3 7.3 Changing W aypoint Position ......... 7-3 7.4 Changing W aypoint Mark Size ..... 7-4 7.5 Entering Routes .....................
iii T ABLE OF CONTENTS BY DISPLA Y ITEM Course bar (Page 13-1) 01 PLOTTER DISPLAY (Page 2-3) SOUNDER DISPLAY (Page 2-5) Fish school (Page 3-10) Bottom (Page 3-10) Position-fixing mode (Page 2-2) Time (Page 11-2) Position (Page 4-2) CSE 350.0 ° SPD 16.
iv FOREWORD A Word to GP-1610CF Owners Congratulations on your choice of the FURUNO GP-1610CF COLOR GPS PLOTTER SOUNDER. W e are confident you will see why the FURUNO name has become synonymous with qual- ity and reliability .
v Features The GP-1610CF is a totally integrated GPS receiver , color video plotter and color video sounder . It mainly consists of a display unit and a GPS antenna.
vi System Configuration The GP-1610CF mainly consists of a display unit and a GPS an- tenna. A dual frequency transducer is optionally available. The chart card drive in the display unit loads electronic charts. External equip- ment which can be connected include water temperature and speed sensors, autopilot, and DGPS beacon receiver .
1-1 INST ALLA TION 1.1 Equipment Lists Standard supply . o Ne m a Ne p y T. o N e d o Cy t Qs k r a m e R 1t i n U y a l p s i D E - F C 0 1 6 1 - P G 1 2t i n U a n n e t n A 6 1 0 - A P G 1 3 n o i .
1-2 Optional equipment (con't) . o Ne m a Ne p y T. o N e d o Cs k r a m e R 8r e c u d s n a r T D S P 5 - 0 2 5 5 2 1 - 5 1 0 - 0 0 0 D W P 5 - 0 2 56 2 1 - 5 1 0 - 0 0 0 m 8 h t i W m o s n a .
1-3 1.2 Installation of Standard Equipment Installing the display unit Mounting considerations The display unit can be installed on a tabletop or on the overhead. When selecting a mounting location for the display unit keep the following in mind: • Keep the display unit out of direct sunlight.
1-4 T abletop mounting Figur e 1-2 Display unit mounting methods Installing the antenna unit Mounting considerations When selecting a mounting location for the antenna unit, keep in mind the following points: • Select a location out of the radar beam.
1-5 Figur e 1-3 T ypical antenna unit mounting locations Antenna unit mounting procedur e Y ou will need a medium size slotted-head screwdriver and vinyl tape. The standard antenna is usually fastened to a length of pipe and fastened to a mast. (A mast mount fixture is optionally available for this.
1-6 2. Screw the pipe into the antenna. DO NOT USE T OOLS T O F ASTEN THE ANTENNA T O ITS MOUNTING; ONL Y HAND TIGHTEN. Pipe Figur e 1-5 Fastening pipe to antenna 3. T ape the junction between the pipe and antenna unit with vinyl tape. Taping Figur e 1-6 T aping the antenna 4.
1-7 5. T ape the antenna unit, mounting fixture and mast with vinyl tape. Vinyl tape Figur e 1-8 Securing antenna to mast with vinyl tape 6. Attach a clamp to the antenna unit and tighten. Leaving some slack in the antenna cable as shown, fix it with vinyl tape.
1-8 Wiring All wiring are terminated at the rear of the display unit. Power cable Connect the power cable to the power connector . Connect the leads to the battery (12 or 24 VDC); white to plus(+) terminal and black to minus(-) terminal.
1-9 Earth terminal ANTENNA UNIT DISPLAY UNIT Ext. equip. DPGS beacon receiver Black White Shield TRANSDUCER Earth Figur e 1-1 1 Display unit, r ear view.
1-10 1.3 Installation of T ransducers Installing the inside-hull mount transducer Necessary tools Y ou will need the following tools: • Sandpaper (#100) • Silicone sealant • Silicone grease Remarks on installation • Do the installation with the boat hauled out of the water .
1-11 Attaching the transducer 1. Clean the transducer face to remove any foreign material. Lightly roughen the transducer face with #100 sandpaper . Also, roughen the inside of the hull where the transducer is to be mounted. 2. W arm the silicone sealant to 40 ° C before usage to soften it.
1-12 Observing the picture 1. Press the POWER key to turn on the display unit. 2. Press the PL TR key . 3. Press the AUT O key . AUTO MODE Cruise Fish Manual Figur e 1-15 Auto mode selection scr een 4.
1-13 If the bottom is displayed in red and the light-blue color appears the mounting location is suitable. Y ou can leave the transducer in position. If the bottom is not displayed in reddish brown, the mounting location is unsuitable. Relocate the transducer and do the following.
1-14 Installing the thru-hull mount transducer T ransducer mounting location This type of mounting provides the best performance of all, since the transducer protrudes from the hull and the ef fect of air bubbles and turbulence neat the hull skin is reduced.
1-15 Acceptable transducer mounting locations Deep-V hull • Position 1/2 to 1/3 length of the hull from stern • 15 to 30 cm off center line (inside first lifting strakes).
1-16 Procedur e for installing the thru-hull mount transducer 1. W ith the boat hauled out of the water , mark the location se- lected for mounting the transducer on the bottom of the hull.
1-17 Installing the transom mount transducer This type of mounting is very commonly employed, usually on relatively small I/O or outboard boats. Do not use this method on an inboard motor boat because turbulence is created by the propel- ler ahead of the transducer .
1-18 M5 x 20 No. 1 M5 x 14 5 ° Tape M5 x 20 Figur e 1-24 T ransom mount transducer , mounting flush with hull Installing the transom mount transducer pr ojecting fr om hull (for deep-V hulls) This method is employed on deep-V hulls and provides good per - formance because the ef fects of air bubbles are minimal.
1-19 1.4 Installation of Optional Sensors Through-hull mount water temperature/speed sensor (ST-02MSB, ST-02PSB) Select a suitable mounting location considering the following: • Select a mid-boat flat position. The sensor does not have to be installed perfectly perpendicular .
1-20 T ransom mount water temperature sensor T -02MTB • Fix the cable at a convenient location with cable clamp. • When the cable is led in through the transom board, make a hole of approx. 17 mm diameter to pass the connector . After passing the cable, fill the hole with a sealing compound.
1-21 SENSOR HOLDER Nut Locknut Washer Rubber washer Coat with silicone sealant. HOLDER GUIDE Thickness of wood plate should be within 25 mm. Figur e 1-28 Thru-hull mount water temperatur e sensor T -03MSB 1.
1-22 GP-1610CF DGPS RD-A RD-B GND 3 4 5 6 7 TD-A TD-B GND BEACON RCVR Note 2: Note 2 RS-422 F.G YEL GRN BLU The signal names depend on equipment connected.
1-23 MJ-A6SRMD SHIELD TEMP TEMP0V/SPD0V SPD +V NC 1 2 3 4 5 6 MJ-A10SRMD NC NC NC NC NC NC NC XDR+ XDR SHIELD XDR- 1 2 3 4 5 6 7 8 9 10 4 7 3 1 2 5 6 8 9 10 MJ-A10SPF TEMP TEMP0V SPD0V/ SHIELD SPD +12.
1-24 1.6 Initial Settings Sensor connection This section should be done with the boat in water . 1. Turn on the power and press the MENU key . 2. Press the [0] key . 3. Press the [5] key to select SENSOR SETUP . SENSOR SETUP SPD SENSOR TEMP SENSOR SPD CALIB TEMP CALIB DEPTH CALIB : Cursor : +/- ESC : Esc STW SOG OWN NMEA -00%(-50~+50) +000 ° C +0.
1-25 NMEA SETUP FORMAT EXT DEVICE 183V1.5 REM : Cursor ESC: Esc 183V2.0 PILOT Figur e 1-35 NMEA setup menu 4. Press t or s to select data format of connected external equip- ment. If you are not sure, try both and select the one which successfully receives data.
1-26 DGPS beacon receiver connection 1. Press the MENU key . 2. Press the [0] key . 3. Press the [8] key . DGPS SETUP DGPS RTCM VER BYTE FORM FIRST BIT PARITY BIT STOP BIT BIT RATES BAUD RATES : Cursor ENT : Sel ESC : Esc ON OFF 1.0 2.0 8-6 8-8 MSB LSB EVEN ODD NONE 1 2 7 8 300 600 1200 2400 4800 9600 Figur e 1-36 DGPS setup menu 4.
2-1 OPERA TIONAL OVER VIEW 2.1 Control Description All operations of the GP-1610CF are carried out with the controls on the front panel of the display unit. All controls respond immediately to your command and the unit emits a beep to signify correct key sequence.
2-2 2.2 Inserting Chart Cards Note: Insert chart card before turning on the power . This enables automatic loading of chart. 1. Open the memory card slot cover at the bottom of the display unit by unfastening two screws. Screws Cover Figur e 2-2 Display unit, bottom 2.
2-3 2.4 Adjusting T one and Brilliance 1. Press the T ONE key . The tone and bril- liance setting display appears. TONE : 5 BRILL : 8 LOW HIGH LOW HIGH Figur e 2-5 T one and display brilliance setting display 2. Operate t or s to adjust display tone. 3.
2-4 Plotter/sounder display This display provides a plotter display on the left 2/3 of the screen an the normal sounder display on the right 1/3. It is useful for search- ing fish schools at cruising speed. CSE 180.0 ° SPD 16.8kt 2D DEP 110m TMP 16.0 ° C 12:13 POS 34 ° 26.
2-5 2.6 Sounder Displays Five sounder displays are available: normal, marker zoom, bottom zoom, bottom-lock and A-scope display . Y ou may select a sounder display with the SNDR key . Selecting a sounder display 1 . Press the SNDR key . The SELECT SOUNDER MODE screen appears.
2-6 Marker zoom display This mode expands anywhere of the normal picture to full vertical size of the screen on the left-half window . Y ou may specify the portion to expand by operating the VRM (V ariable Range Marker), which you can shift with ▲ or ▼ .
2-7 2.7 Basic Menu Operation 1. Press the MENU key to display the MAIN menu. MAIN MENU 1. DISPLAY SETUP 2. TRACK/MARK SETUP 3. ERASE TRACK/MARK 4. ROUTE/ROUTE LIST 5. ALARM SETUP 6. VIDEO SOUNDER SETUP 7. MEMORY SAVE/LOAD 8. CLEAR MEMORY 0. SYSTEM MENU : Cursor ESC: Esc Figur e 2-19 Main menu 2.
3-1 3.1 Principle of Operation The video sounder of the GP-1610CF deter- mines the distance between its transducer and underwater objects such as fish, lake bottom or seabed and displays the results on screen.
3-2 3.2 Automatic Sounder Operation Automatic operation is useful when you are preoccupied with other tasks and do not have time to adjust the display . How it works The automatic function automatically selects the proper gain and range scale according to depth.
3-3 Too high Proper Too low Figur e 3-4 Examples of pr oper and impr oper gain 5. Press ▲ to select Range. 6. Press t or s to select basic range de- sired. 7. Press ▼ to select Shift. Display Shift Figur e 3-5 Shift concept 8. Press t or s to shift the basic range, if desired.
3-4 3.5 Selecting Picture Advance Speed When selecting a picture advance speed, keep in mind that a fast advance speed will expand the size of the fish school horizontally on the screen and a slow advance speed will con- tract it. 1. Press the MENU key .
3-5 Weak echoes Signal level adjusted Figur e 3-1 1 How SIG LEV works 3.8 Changing Zoom Magnification Factor Y ou may select the zoom magnification fac- tor for the marker and bottom zoom modes. This the amount the zoomed picture is mag- nified in relation to the normal picture.
3-6 2. Press the [6] key to display the VIDEO SOUNDER SETUP menu. 3. Press ▲ or ▼ to select DEP CHIME. 4. Press t or s to select ON or OFF . 5. Press the MENU key . 3.12 Selecting Unit of Depth Measurement Y ou may display the depth in meters, feet or fathoms as follows: 1.
3-7 3. Press ▲ or ▼ to select TEMP GRP . 4. Press t or s to select ON or OFF . 5. Press the MENU key . 200k 162 0 50 100 150 200 68.3 CSE 180.0° SPD 16.8kt DEP 162m TMP 16.0 °C 2D 14:32 POS 34° 26.245' N 135° 41.232' E Water temp. scale °C 30 20 10 0 Water temp.
3-8 4. Press s or t to select NORMAL or B/L (Bottom Lock). 5. Press ▼ to send the cursor to the second line (Range or B/L). 6. Key in the depth desired. 7. Press the ENT key . 8. Press the MENU key . 3.18 Bottom Alarm The bottom alarm sounds when the seabed depth is narrower than the alarm range set.
3-9 SNDR SETUP EXP MARKER GAIN ADJ 50k 200k BTM-LOCK TRANSMIT ON OFF (-20~+20) +00 +00 NARROW WIDE ON OFF : Cursor ESC: Esc Figur e 3-20 Sounder setup menu 4. Operate the Cursor Pad to select EXP MARKER. 5. Operate the Cursor Pad to select ON or OFF .
3-10 3.24 Interpreting the Display Zero line The zero line (sometimes referred to as the transmission line) represents the transducer ’ s position, and moves off the screen when a deep phased range is used. Zero line Shift Figur e 3-21 Zer o line Fish school echoes Fish school echoes will generally be plotted between the zero line and the bottom.
3-11 Surface noise/aeration When the waters are rough or the boat passes over a wake, surface noise may appear near the zero line. As surface turbulence is acous- tically equivalent to running into a brick wall, the bottom echo will be displayed intermit- tently .
4-1 GPS, CHART OVER VIEW 4.1 Principle of GPS What is GPS? GPS is an acronym meaning Global Position- ing System. GPS (sometimes referred to as NA VST AR) is a highly precise satellite navi- gation system developed by the U.S. Depart- ment of Defense.
4-2 Position-fixing accuracy (HDOP) In radar position-fixing, most accurate posi- tion fixes are obtained when the tar gets used are spaced nearly 90 ° from each other .
4-3 4.2 Presentation Mode T wo types of display presentations are pro- vided for the plotter display and plotter/ sounder display: north-up and course-up. Y ou can select one with the NU/CU key . North-up North (zero degrees) is at the top of the dis- play and own ship is at the center of the screen.
4-4 4.4 Selecting Screen Center by Cursor 1. Press the CURS key to display the cur- sor . 2. Operate the Cursor Pad to place the cur- sor where desired. 3. Press the CNTR key . 4.5 Shifting the Display 1. Press the CURS key to turn off the cur - sor .
4-5 Remarks on chart display A chart will not be displayed in the following conditions: • When the chart scale is too large or too small. • When scrolling the chart outside the indi- ces. When this happens, the message NO CHAR T appears for a couple of seconds.
4-6 Difference between FURUNO and NA VIONICS charts T able 4-4 Comparison of chart systems m e t IO N U R U FS C I N O I V A N g n i l l o r c s t o D y t i l i b a p a c S E YS E Y p u - e s r u o C .
5-1 5.1 Stopping/Restarting Plotting of T rack When your boat is at anchor or returning to port you probably won't need to record its track. Y ou can stop recording the track, to conserve the track memory , as follows: l. Press the MENU key . 2 .
5-2 ERASE TRACK/MARK MARK ERASE TRACK ERASE MARK USED TRACK USED : Cursor : Go ESC: Esc 15/100 PT 1200/2000 PT NO YES NO NO YES Figur e 5-3 Erase track/mark menu 3. Operate the Cursor Pad to select TRACK ERASE. 4. Press s to select YES. Y ou are asked if you are sure you want to erase all track.
6-1 6.1 Entering Marks Y ou can inscribe marks on the plotter display to denote important locations; for example, buoy , fishing point, wreck, etc. Further , marks can be connected with lines to depict an area such as a hot fishing spot. 100 marks may be entered.
6-2 6.3 Erasing Individual Marks Marks can be erased individually or collec- tively . How to erase marks collectively will be discussed later . 1. Press the CURS key to turn on the cursor . 2. Operate the Cursor Pad to place the cur- sor on the mark to erase.
6-3 6.5 Entering the MOB Mark The MOB mark functions to mark man over- board position. The range and bearing to the MOB position are continuously updated on the display , to help you navigate to the MOB position. Entering the MOB mark 1. Press the EVENT MOB key over 3 sec- onds.
6-4 3. Operate the Cursor Pad to select MARK ERASE. 4. Press s to select YES. Y ou are asked if you are sure to erase all marks. Are you sure? ENT: YES ESC: NO 5.
7-1 W A YPOINTS, ROUTES 7.1 Entering W aypoints In navigation terminology , a waypoint is a particular location on a voyage whether it be a starting, intermediate or destination point. A waypoint is the simplest piece of informa- tion the GP-1610CF requires to get you to a destination, in the shortest distance possible.
7-2 b) Press the ENT key . c) Repeat a) and b) to complete the com- ment. A comment may contain 10 characters. d) Select ENTER. e) Press the ENT key . 9.
7-3 1 1. Press the ENT key . 12. Press the MENU key twice. Entering waypoints by event position or MOB position 1. Press the WPT key . 2. Press the WPT key to select Evnt to WPT . 3. Press the ENT key . The event list appears. EVENT LIST No. MOB 001 LAT 32 ° 59.
7-4 Note: If the waypoint selected is part of a route you are asked whether it is alright to edit the waypoint. ROUTE DELETE ENT: YES ESC: NO ROUTE IN USE DELETE? ENT: YES ESC: NO When route is in use 7. Press the ENT key to register changes. 8. Press the MENU key to escape.
7-5 4. Press the ENT key . _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ : Cursor WAYPOINT LIST No. 001 004 007 LAT/LONG COMMENT 123 ° 00.000’E 23 ° 00.
8-1 SETTING DESTINA TION 8.1 Setting Destination The GP-1610CF offers four methods by which you can set destination: • Previously entered waypoint • Cursor position • Event position/MOB position • Route Setting destination by waypoint 1. Press the GOTO key .
8-2 Own ship's position is marked as "00." A light- blue line connects own ship with destination, marked with a flag, and it shows the shortest course to the destination. Range and bearing from own ship to the destination appears at the bottom of the screen.
8-3 8.2 Skipping Route W aypoints There are times when you won't need to fol- low all waypoints in a route. In Figure 8-7, for example, the ship has skipped waypoint 04. Port Port WPT 04 WPT 05 WPT 03 New course WPT 02 WPT 01 WPT 06 Figur e 8-7 How a waypoint is skipped 1.
9-1 PLOTTER-RELA TED ALARMS 9.1 Arrival/Anchor W atch Alarm The arrival alarm informs you that your boat is approaching a destination waypoint. The area that defines an arrival zone is that of a circle which you approach from the outside of the circle.
9-2 9.2 XTE (Cross T rack Error) Alarm The XTE alarm warns you when your boat is of f its intended course. When your boat goes of f course by the alarm range set, the audible alarm sounds and the alarm icon and the indication XTE appears. Y ou may silence the alarm with the CLR key .
10-1 10.1 Displaying Position in LOPs Position can be displayed in latitude and lon- gitude, Loran C LOPs or Decca LOPs. Displaying position in Loran C LOPs 1. Press the MENU key . 2. Press the [0] key to select the SYSTEM menu. 3. Press the [2] key to select PL TR SETUP .
10-2 5. Consulting a nautical chart, enter offset with numeric keys. 6. Press the ENT key . 7. Press the MENU key . L L appears on the display . T o remove the of fset, enter zeroes at step 5 in the above the procedure.
10-3 10.6 Offsetting Chart Position In some instances chart position may be off by a few minutes. For example, the position of the ship is shown to be at sea while it is in fact moored at a pier . Y ou can compensate for this error as follows: 1. Press the MENU key .
11-1 GPS OPERA TIONS 1 1.1 GPS Setup Menu The GPS setup menu provides for the setting up of GPS-related operations. 1. Press the MENU key . 2. Press the [0] key . 3. Press the [7] key . GPS SETUP GPS SMOOTHING GEODETIC POS CALIB UNHEALTH TIME DIFF _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Posn Speed 000 (000~999) 000 (000~999) WGS-84 OTHER (002) 0 0.
11-2 UNHEAL TH: Every GPS satellite is broad- casting abnormal satellite number(s) in the Almanac. Using this information, the GPS receiver eliminates any malfunctioning satel- lite from the GPS satellite schedule.
12-1 OPTIONAL EQUIPMENT SETUP 12.1 Selecting Sensors The sensor setup menu provides for selection and calibration of speed and temperature sen- sors (optional equipment). 1. Press the MENU key . 2. Press the [0] key . 3. Press the [5] key . SENSOR SETUP SPD SENSOR TEMP SENSOR SPD CALIB TEMP CALIB DEPTH CALIB STW OWN +00% (-50~+50) +00.
12-2 DGPS SETUP DGPS RTCM VER BYTE FORM FIRST BIT PARITY BIT STOP BIT BIT RATES BAUD RATES ON 1.0 8-6 MSB EVEN 1 7 300 2400 : Cursor 1200 4800 9600 OFF 2.0 8-8 LSB ODD NONE 2 8 600 ENT: Sel ESC: Esc Figur e 12-3 DGPS setup menu 4. Display DGPS ON and set other items according to specifications of beacon re- ceiver .
13-1 CUST OMIZING THE DISPLA Y 13.1 Plotter Display Marker Attributes The various markers and items shown on the plotter display can be turned on/off and their color changed on the DISPLA Y SETUP menu.
13-2 13.3 Unit of Distance Measurement Y ou may display range in nautical miles, ki- lometers or statute miles as follows: 1. Press the MENU key . 2 . Press the [0] key to select SYSTEM MENU.
14-1 MAINTENANCE & TROUBLESHOOTING 14.1 Maintenance Regular maintenance is essential for good per- formance. A maintenance program should be established and should at least include the items listed in T able 14-l.
14-2 A battery installed on a circuit board inside display unit preserves data when the power is turned of f. The life of the battery is about three years. When the battery voltage is low the battery icon appears on the display . When this happens, contact your dealer to request replacement of the battery .
14-3 T able 14-2 Simple troubleshooting (con't) . . . f I. . . n e h T r e d n u o S o e d i V d n a s k r a m t u b e r u t c i p o n r a e p p a s r e t c a r a h c O E D I V e h t n o " 0 " o t t e s s i d e e p s e c n a v d a e r u t c i p f i k c e h c .
14-4 14.5 Diagnostic T ests Memory, I/O port test This test conduct a general check of the dis- play unit and the antenna unit. The unit dis- plays the check results for each device or component checked as OK or NG (No Good). 1. Press the MENU key . 2 .
14-5 Display test 1. Press the MENU key to display the main menu. 2 . Press the [0] key to select SYSTEM MENU. The system menu appears. 3. Press the [1] key to select SELF TEST . 4 . Press the [4] key to select DISPLA Y TEST . DISPLAY TEST WHT GRN BLU BLK WHT RED GRN BLU BLK RED ENT: Change Mode ESC: Esc Figur e 14-3 Display test pattern 5.
14-6 Data Rx: Shows DGPS beacon receiver is normal or abnormal. T wo dashes appear when no DPGS beacon receiver is connected. Ref Sta: Shows status of DPGS transmitting station. T wo dashes appear when no DPGS beacon receiver is connected. Pr ogram No.
14-7 5. Press the ENT key . The card is formatted and data are saved. When saving is com- pleted, the cursor moves to NO at the SA VE MEMOR Y line. 6. Press the MENU key .
A-1 Specifications Video Sounder Frequency 50 kHz and 200 kHz Display range 5, 10, 20, 40, 80, 160, 300 meter (feet, fathoms, and passi/braza also available) Shift 0 to 300 m Display mode Normal, mark.
A-2 W orld T ime Standards.
A-3 Geodetic Chart List 001: WGS84 002: WGS72 003: TOKYO : Mean V alue (Japan, Korea & Okinawa) 004: NORTH AMERICAN 1927 : Mean V alue (CONUS) 005: EUROPEAN 1950 : Mean V alue 006: AUSTRALIAN GEOD.
A-4 Icons L L H • Unsuitable chart/chart card not inserted. • Chart scale/range is too small. (Page 4-4) • Suitable chart scale is selected. (Page 4-4) • Chart position is offset. (Page 10-3) • Battery voltage (on pcb) is low. (Page 14-1) • Chart scale/range is too large.
A-5 GPS Plotter Almanac Each GPS satellite broadcasts its own orbital data as well as general orbital data of all other GPS satellites. This general orbital data is called the Almanac.
A-6 Magnetic variation offset The location of the magnetic north pole is dif- ferent from the geographical north pole. This causes a difference between the true and mag- netic north direction. This dif ference is called magnetic variation, and varies with respect to the observation point on the earth.
A-7 V ideo Sounder Clutter Cruising noise, polluted water or plankton can clutter the screen with low signal level ech- oes. This situation can be improved by ad- justing the CLUTTER function. Detecting area The detecting area varies with the main beamwidth of the transducer .
A-8 Returning signal The ultrasonic pulse transmitted by the trans- ducer "strikes" intervening objects such as the bottom and fish schools and returns to the transducer . The signal received at the trans- ducer is called the returning signal.
A-9 Menu T ree MENU key 1. DISPLAY SETUP 2. TRACK/MARK SETUP 3. ERASE TRACK/MARK 4. ROUTE/ROUTE LIST 5. ALARM SETUP (Continued on next page) HUE LAND BRIGHT LAND COLOR PLACE NAME GRID COLOR COURSE BAR.
A-10 6. VIDEO SOUNDER 7. MEMORY SAVE/LOAD 8. CLEAR MEMORY 0. SYSTEM MENU CLUTTER ADVANCE NOISE LM DEP CHIME TEMP GRP SIG LEV ZOOM HUE SAVE MEMORY LOAD MEMORY 1. SELF TEST 2. PLTR SETUP 3. SOUNDER SETUP (Continued on next page) 1. GPS MONITOR DISPLAY 2.
A-11 4. UNIT SETUP 5. SENSOR SETUP 6. NMEA SETUP 7. GPS SETUP 8. DPGS SETUP 9. CHART POSN CALIB DISTANCE DEPTH TEMP SPD SENSOR TEMP SENSOR SPD CALIB TEMP CALIB DEPTH CALIB FORMAT EXT DEVICE GPS SMOOTH.
A-12 Decca Chains n i a h C . o n n i a h C n i a h C e d o c n o i t a c o L n i a h C . o n n i a h C n i a h C e d o c n o i t a c o L 1 0c i t l a B h t u o SA 0e p o r u E4 3o t n a KC 8n a p a J.
.
.
.
.
.
Index-1 INDEX A A-scope display 2-6 Alarms arrival/anchor watch 9-1 bottom 3-8 fish 3-7 speed 9-2 trip 9-2 water temperature 3-8 XTE 9-2 Antenna unit installation 1-4 Arrival/anchor watch alarm 9-1 AU.
Index-2 G Gain offset 3-9 Geodetic chart system 1 1-1 Glossary A-5 GPS disabling satellites 1 1-2 monitor display 14-5 position smoothing 1 1-1 principle 4-1 speed smoothing 1 1-1 GPS Monitor Display .
Index-3 mark shape 6-2 mark size 6-2 navaid selection 10-2 of fsetting GPS position 10-1 position in LOPs (Loran or Decca) 10-1 presentation mode 4-3 radar target mark 6-4 skipping route waypoints 8-3.
デバイスFuruno GP-1610CFの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Furuno GP-1610CFをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはFuruno GP-1610CFの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Furuno GP-1610CFの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Furuno GP-1610CFで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Furuno GP-1610CFを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はFuruno GP-1610CFの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Furuno GP-1610CFに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちFuruno GP-1610CFデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。