Garminメーカー190-01834-00_OBの使用説明書/サービス説明書
ページ先へ移動 of 30
echoMAP ™ 40/50/70/90 Series Owner’s Manual December 2014 Printed in Taiwan 190-01834-00_0B.
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements.
Table of Contents Introduction ..................................................................... 1 Front View ................................................................................... 1 Device Keys .......................................
Sonar Appearance Settings ................................................. 15 Advanced Sonar Settings .................................................... 15 Sonar Installation Settings ................................................... 16 Sonar Alarm Settings .
Introduction WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Front View À Power key Á Device keys  microSD ™ memory card slot à Automatic backlight sensor Device Keys Turns on and off the device when held.
4 Wait several minutes while the software update process completes. The device returns to normal operation after the software update process is complete. 5 Remove the memory card. NOTE: If the memory card is removed before the device restarts fully, the software update is not complete.
Icon Description Tide station Current station Overhead photo available Perspective photo available Other features common to most charts include depth contour lines, intertidal zones, spot soundings (as depicted on the original paper chart), navigational aids and symbols, obstructions, and cable areas.
You can view indicators for animated tide station and current direction on the Navigation chart or the Fishing chart. You must also enable animated icons in the chart settings ( Showing and Configuring Tides and Currents ). An indicator for a tide station appears on the chart as a vertical bar graph with an arrow.
course line does not appear. Changes in the speed, course over ground, or rate of turn information transmitted by the vessel can impact the calculation of the projected course line.
Chart and 3D Chart View Settings NOTE: Not all settings apply to all charts and 3D chart views. Some options require premium maps or connected accessories. These settings apply to the charts and 3D chart views, except Fish Eye 3D ( Fish Eye 3D Settings ).
Symbols : Shows and configures the appearance of various symbols on the chart, such as the vessel icon, navaid symbols, land POIs, and light sectors. Style : Sets how the chart appears over 3D terrain. Hazard Colors : Shows shallow water and land with a color scale.
Basic Navigation Questions Question Answer How do I make the chartplotter point me in the direction in which I want to go (bearing)? Navigate using Go To.
Stopping Navigation From the Navigation chart or Fishing chart, select MENU > Stop Navigation . Waypoints Waypoints are locations you record and store in the device. Marking Your Present Location as a Waypoint From any screen, select MARK . Creating a Waypoint at a Different Location 1 Select User Data > Waypoints > New Waypoint .
• To select a turn using the chart, select Edit Turns > Route Using Chart , and select a location on the chart. Browsing for and Navigating a Saved Route Before you can browse a list of routes and navigate to one of them, you must create and save at least one route.
Retracing the Active Track The track currently being recorded is called the active track. 1 Select User Data > Tracks > Follow Active Track . 2 Select an option: • Select the time the active track began. • Select Entire Log . 3 Review the course indicated by the colored line.
5 Review the placement of the Auto Guidance line, and determine whether the line safely avoids known obstacles and the turns enable efficient travel. 6 Select an option: • If the placement of the Auto Guidance line is satisfactory, select MENU > Stop Navigation , and proceed to step 10.
The adjustments you can make to each sonar view vary depending on the view you are in and the chartplotter model and transducer you have connected. Sonar Views The sonar views available vary depending on the type of transducer and optional sounder module connected to the chartplotter.
1 From a sonar view, select MENU > Sonar Setup > Installation > Transducer Type . 2 Select an option: • If you have a 200/77 kHz, dual-beam transducer, select Dual Beam (200/77 kHz) . • If you have a 200/50 kHz, dual-frequency transducer, select Dual Frequency (200/50 kHz) .
1 From a sonar view, select MENU > Sonar Setup > Scroll Speed . 2 Select an option: • To adjust the scroll speed automatically using speed-over- ground or water speed data, select Auto . The Auto setting selects a scroll rate to match the boat speed, so targets in the water are drawn with the correct aspect ratio and appear less distorted.
appearance of noise near the surface. When the value of this setting is increased, the colors associated with low-level noise and fish targets appear more consistent through various water depths. This setting also reduces the noise near the surface of the water.
Viewing Tide Station, Current Station, or Celestial Information for a Different Date 1 Select Navigation Info > Tides & Currents . 2 Select Tides , Currents , or Celestial . 3 Select an option. • To view information for a different date, select Change Date > Manual , and enter a date.
vessel, and a blue flag indicates the last reported position of the vessel. 1 From a chart or 3D chart view, select MENU > Other Vessels > DSC Trails . 2 Select the number of hours to show tracked vessels on the chart. For example, if you select 4 Hours, all trail points that are less than four hours old appear for all tracked vessels.
Restoring Backup Data to a Chartplotter 1 Insert a memory card into a card reader that is attached to the computer. 2 Copy a backup file from the computer to the memory card, into a folder named GarminUserData. 3 Insert a memory card into the card slot.
2 Select Settings > My Vessel > Keel Offset . 3 Select or based on the location of the transducer. 4 Enter the distance measured in step 1. Setting the Water Temperature Offset Before you can set the water temperature offset, you must have a NMEA 0183 water-temperature sensor or a temperature- capable transducer to measure water temperature.
Time Zone : Sets the time zone, or allows automatic selection based on GPS location. Navigation Settings NOTE: Some settings and options require additional charts or hardware. Select Settings > Navigation . Route Labels : Sets the type of labels shown with route turns on the map.
longitude in degrees and minutes, with options for degrees, minutes and second, degrees only, or one of several grid formats. Map datum is a math model which depicts a part of the surface of the earth. Latitude and longitude lines on a paper map are referenced to a specific map datum.
Index A aerial photos 4 AIS 4, 5, 7 alarm 5 distress signal device 5 SART 5 targeting 4, 5 threats 5 turning on 21 vessels 5 alarms 20 anchor drag 20 arrival 20 col.
list 10 navigating 10, 11 recording 11 saving 10 saving as route 10 showing 6, 10 transducer 12, 13, 16 trip gauges 16 trip planner.
.
www.garmin.com/support +43 (0) 820 220230 + 32 2 672 52 54 0800 770 4960 1-866-429-9296 +385 1 5508 272 +385 1 5508 271 +420 221 985466 +420 221 985465 + 45 4810 5050 + 358 9 6937 9758 + 331 55 69 33 .
デバイスGarmin 190-01834-00_OBの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Garmin 190-01834-00_OBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGarmin 190-01834-00_OBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Garmin 190-01834-00_OBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Garmin 190-01834-00_OBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Garmin 190-01834-00_OBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGarmin 190-01834-00_OBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Garmin 190-01834-00_OBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGarmin 190-01834-00_OBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
