GarminメーカーGPSMAP 741xsの使用説明書/サービス説明書
ページ先へ移動 of 48
GPSMAP ® 500/700 Series and echoMAP ™ 50/70 Series Owner’s Manual March 2015 Printed in Taiwan 190-01556-10_0D.
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements.
Table of Contents Introduction ..................................................................... 1 echoMAP 70 Series and GPSMAP 700 Series .......................... 1 Using the Touchscreen .........................................................
Creating a Waypoint on the Sonar Screen Using the Touchscreen ............................................................................. 16 Creating a Waypoint on the Sonar Screen Using the Device Keys ..............................................
Opening the Media Player ........................................................ 28 Icons .................................................................................... 28 Selecting the Media Source .............................................
.
Introduction WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. echoMAP 70 Series and GPSMAP 700 Series À Power key Á Automatic backlight sensor  Touchscreen à microSD ™ memory card slots Using the Touchscreen • Tap the screen to select an item.
4 Close the door. Software Update You may need to update the device software when you install the device or add an accessory to the device. Loading the New Software on a Memory Card 1 Insert a memory card into the card slot on the computer. 2 Go to www.
You will need this password to access the wireless network from a wireless device. The password is case-sensitive. Connecting a Wireless Device to the Chartplotter Before you can connect a wireless device to the chartplotter wireless network, you must configure the chartplotter wireless network ( Setting Up the Wi ‑ Fi ® Wireless Network ).
2 Select Stop Panning or Back to stop panning and return the screen to your present location. Selecting an Item on the Map Using the Device Keys 1 From a chart or 3D chart view, select , , , or to move the cursor. 2 Select SELECT . Measuring a Distance on the Chart 1 From a chart or the Radar overlay, select a location.
Fishing Charts : Shows the chart with enhanced bottom contours and without navigational data. This chart works well for offshore deep-sea fishing. High Resolution Satellite Imagery : Provides high-resolution satellite images for a realistic view of the land and water on the Navigation chart ( Showing Satellite Imagery on the Navigation Chart ).
Symbol Description Target is lost. A green X indicates that the AIS transmission from the vessel is lost, and the chartplotter displays a message banner asking whether the vessel should continue to be tracked. If you discontinue vessel tracking, the lost target symbol disappears from the chart or the 3D chart view.
AIS Distress Signal Device Targeting Symbols Symbol Description AIS distress signal device transmission. Select to see more information about the transmission and begin navigation. Transmission lost. Transmission test. Appears when a vessel initiates a test of their distress signal device, and does not represent a true emergency.
Compass Tape : Shows the compass tape data bar when the vessel is navigating to a destination. Editing the Data Fields You can change the data shown in the overlay numbers displayed on the charts and other screens. 1 From a screen that supports overlay numbers, select Menu .
Fish Eye 3D Settings NOTE: This feature is available with premium charts, in some areas. From the Fish Eye 3D chart view, select Menu. View : Sets the perspective of the 3D chart view. Tracks : Shows tracks. Sonar Cone : Shows a cone that indicates the area covered by the transducer.
Creating a Waypoint at a Different Location 1 Select Nav Info > Waypoints > New Waypoint . 2 Select an option: • To create the waypoint by entering position coordinates, select Enter Coordinates , and enter the coordinates. • To create the waypoint using a chart, select Use Chart , select the location, and select Select .
9 Follow the magenta line, steering to avoid land, shallow water, and other obstacles. Creating and Saving a Route This procedure saves the route and all the waypoints in it. The starting point can be your present location or another location. 1 Select Nav Info > Routes & Auto Guidance Paths > New Route > Route Using Chart .
Creating and Saving an Auto Guidance Path 1 Select Nav Info > Routes & Auto Guidance Paths > New Route > Auto Guidance . 2 Select a starting point, and select Next . 3 Select a destination, and select Next . 4 Select an option: • To view a hazard and adjust the path near a hazard, select Hazard Review .
Showing Tracks From a chart or a 3D chart view, select Menu > Waypoints & Tracks > Tracks > On . A trailing line on the chart indicates your track. Setting the Color of the Active Track 1 Select Nav Info > Tracks > Active Track Options > Track Color .
Combinations The Combination screen shows a combination of different screens at the same time. The number of options available on the Combination screen depends on the optional devices you have connected to your chartplotter and whether you are using premium maps.
 The transducer on your vessel à Trees Ä Old tires Å Logs Æ Distance from the side of the boat SideVü/DownVü Scanning Technology Instead of a more common conical beam, the SideVü/DownVü transducer uses a flat beam to scan the water and ground to the sides of your boat.
RealVü 3D Down Sonar View This sonar view shows a three-dimensional view of what is below the transducer and can be used when you are stationary and want to see what is around your boat.
Adjusting the Level of Detail You can control the level of detail and noise shown on the sonar screen either by adjusting the gain for traditional transducers, or by adjusting the brightness for DownVü and SideVü/DownVü transducers.
Some sonar black boxes and transducers also provide the ability to customize preset frequencies for each transducer element, which enables you to change the frequency quickly using the presets as the water and your goals change.
On-screen Control : Sets the behavior of the buttons on the sonar screen control. This is available for touchscreen devices. Range Lines : Shows the vertical lines indicating the distance to the right and left of the boat. This setting is available for SideVü sonar view.
Wider beam widths generate larger arches for fish target returns, making them ideal for locating fish. Wider beam widths also perform better in deep water, because the lower frequency has better deep water penetration. Wider beam widths can also generate more surface noise and reduce bottom signal continuity during rough sea conditions.
5 Select Menu > Transmit Radar . Adjusting the Radar Range The range of the radar signal indicates the length of the pulsed signal transmitted and received by the radar. As the range increases, the radar transmits longer pulses in order to reach distant targets.
• To show the tracks of AIS vessels, select Trails , and select the length of the track that appears. VRM and EBL The variable range marker (VRM) and the electronic bearing line (EBL) measure the distance and bearing from your boat to a target object.
NOTE: Depending upon the radar in use, the gain setting configured for use in one radar mode may or may not be applied to other radar modes or to the Radar overlay. NOTE: Not all options and settings are available on all radar and chartplotter models.
NOTE: Depending upon the radar in use, the settings configured for use in one radar mode may or may not be applied to other radar modes or to the radar overlay.
From the engine gauges screen, select Menu > Gauge Setup > Status Alarms > On . When an engine alarms is triggered, a gauge status alarm message appears and the gauge may become red depending on the type of alarm.
2 Select an option: • To set the top of the wind gauge to a North heading, select North Up . • To rotate the gauge so the direction in which you are moving is at the top, select Head Up . Configuring the Heading Source of the Environment Gauge You can specify the source of the heading displayed on the environment gauge.
information was sent with the distress call, that information is also available and recorded with the call. designates a distress call in the DSC list and marks the position of the vessel on the Navigation chart at the time of the DSC distress call.
6 On your Garmin VHF radio, select Call . Making an Individual Routine Call to an AIS Target 1 From a chart or 3D chart view, select an AIS target. 2 Select AIS Vessel > Call with Radio . 3 If necessary, select Channel , and select a new channel. 4 Select Send .
Muting the Media Volume 1 From the media screen, select . 2 If necessary, select Select . Scanning VHF Channels Before you can scan VHF channels, you must set the source to VHF. You can monitor VHF channels saved as presets for activity and automatically switch to an active channel.
2 Select an option: • To show the video using a stretched aspect ratio, select Aspect > Stretch . The video cannot be stretched beyond the dimensions provided by the connected video device, and it may not fill the entire screen. • To show the video using a standard aspect ratio, select Aspect > Standard .
2 Select an option: • To view the weather forecast for the next 48 hours, in 12- hour increments, select Next Forecast or multiple times. • To view the weather forecast for the previous 48 hours, in 12-hour increments, select Previous Forecast or multiple times.
1 From the weather fishing chart, select Menu > Sea Temperature . 2 Select an option: • To allow the chartplotter to adjust the temperature range automatically, select Auto Configure . The chartplotter automatically finds the lower and upper limits for the current screen, and updates the temperature- color scale.
System Information : Provides information about the device and the software version. Simulator : Turns on the simulator and allows you to set the speed and simulated location. Display Settings Not all options are available on all models. Select Settings > System > Display .
Setting the Water Temperature Offset Before you can set the water temperature offset, you must have a NMEA 0183 water-temperature sensor or a temperature- capable transducer to measure water temperature. The temperature offset compensates for the temperature reading from a temperature sensor.
System Units : Sets the unit format for the device. Variance : Sets the magnetic declination, the angle between magnetic north and true north, for your present location. Heading : Sets the direction references used in calculating heading information. True sets geographic north as the north reference.
whether the line safely avoids known obstacles and the turns enable efficient travel. Auto Guidance maintains a wide clearance from obstacles in open water, even if you set the Shoreline Distance setting to Near or Nearest.
Cleaning the Screen NOTICE Cleaners containing ammonia will harm the anti-reflective coating. The device is coated with a special anti-reflective coating which is very sensitive to skin oils, waxes, and abrasive cleaners. 1 Apply an eyeglass lens cleaner specified as safe for anti- reflective coatings to the cloth.
Type Sentence Description GPRMB RMB: Recommended minimum navigation information GPRMC RMC: Recommended minimum specific GNSS data GPRTE RTE: Routes GPVTG VTG: Course over ground and ground speed GPWPL.
Index A aerial photos 5 AIS 5, 7, 8 alarm 6 distress signal device 6, 7 radar 21 SART 7 targeting 5–7 threats 6, 21 turning on 36 vessels 6 alarms 34 anchor drag .
echo trails 23, 24 field of view 24 front-of-boat offset 24 gain 22, 23 optimizing display 23 overlay screen 22 range 21 range rings 24 sentry mode 21 timed transmit 21 t.
.
www.garmin.com/support +43 (0) 820 220230 + 32 2 672 52 54 0800 770 4960 1-866-429-9296 +385 1 5508 272 +385 1 5508 271 +420 221 985466 +420 221 985465 + 45 4810 5050 + 358 9 6937 9758 + 331 55 69 33 .
デバイスGarmin GPSMAP 741xsの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Garmin GPSMAP 741xsをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGarmin GPSMAP 741xsの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Garmin GPSMAP 741xsの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Garmin GPSMAP 741xsで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Garmin GPSMAP 741xsを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGarmin GPSMAP 741xsの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Garmin GPSMAP 741xsに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGarmin GPSMAP 741xsデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
