GarminメーカーGPSMAP 76の使用説明書/サービス説明書
ページ先へ移動 of 81
GPSMAP 76 owner’ s manual & r efer ence guide covers.indd 03/14/01, 12:35 PM 1.
©2001 GARMIN Corporation GARMIN International, Inc. 1200 East 151 st Street, Olathe, Kansas 66062 U.S.A. T el. 913/397.8200 Fax 913/397.8282 GARMIN (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey , SO51 9AQ, U.K. T el. 44/1794.
GPSMAP 76 Registration Help us better support you by completing your on-line registration today! Why should you register your GPSMAP 76? • Notifi cation of Product Updates • Notifi cation of New Products • Lost or Stolen unit T racking Connect to our website ( www .
W ARNING: If you choose to use the GPSMAP 76 in a vehicle, it is the sole responsibility of the owner/operator of the GPSMAP 76 to secure the GPS unit so that it will not cause damage or personal injury in the event of an accident.
The GPSMAP 76 complies with Part 15 of the FCC limits for Class B digital devices. This equipment generates, uses, and can radiate radio frequency ener gy and, if not installed or used in accordance with the instructions may cause harmful interference to radio communications.
The GPSMAP 76 is a 7.5 ounce, 12 channel, hand held GPS receiver with a built-in Quad Helix antenna. The GPSMAP 76 has nine Keys located on the front of the unit, that allow the user to quickly access all of the units functions.
5 Introduction T able of Contents Introduction.................................... 1-7 Registration ........................................ 1 W ar nings and Precautions .................. 2 FCC Compliance Statement ............... 3 Features.........
The list to the right is pr ovided to help you quickly fi nd some of the mor e important pr ocedur es you will use on your new GPSMAP 76. H TO DO THIS: SEE P AGE(S): T urn the unit on or off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Introduction GPSMAP 76 Internal Antenna 180 x 240 Four Level Gray , Backlight Display Interface Keys External Antenna Connection Battery Compartment External Data/Auxilary Power Port 190-00230-00.
Remove the batteries from your GPSMAP 76 if you don’ t expect to use it for several months. Be sur e to observe the proper polarity when inserting the batteries. Follow the bat- tery manufactur er’ s instr uctions on the proper car e and han- dling of the batteries.
9 Getting Started T o install the Lanyard: 1. Place the loop of the Lanyard through the slot opening at the bottom of the GPSMAP 76. 2. Route the strap through the loop and pull tight.
10 Interface K eys IN — The Zoom IN Key is used to decr ease the map scale. When you decrease the map scale, you will view a smaller area on the map with greater detail. OUT — The Zoom OUT Key is used to increase the map scale. When you increase the map scale, you will view a lar ger area on the map with less detail.
11 Getting Started Main P ages This exercise will pr ovide you with the knowledge and skill to navigate the pages and menus of your GPSMAP 76 with confi dence. As we progr ess through this Owner’ s Manual you will often be directed to press a specifi ed Interface Key or highlight a fi eld.
I 12 Getting Started While learning the basic operation of the GPSMAP 76, let’ s put the unit into Simulator Mode. The Simulator Mode is great for practicing with the unit while inside and satellite signals are not available.
13 Getting Started Using the Interface K eys The Interface Keys are your link with the GPSMAP 76. Let’ s take a few minutes and see what some of the Interface Keys are used for . W ith the GPS Information Page displayed, press the PA G E Key several times.
14 Getting Started Entering Data There will be many times that you may need to enter data. An example is naming a waypoint. The ROCKER Key is used to navigate through menu items and to enter data. Let’ s combine a couple of lessons. W e will create a new waypoint, enter a waypoint name, and assign a symbol to the waypoint.
15 Getting Started Changing the name: 1. Press the ROCKER K ey right to highlight the Name Field then press the ENTER Ke y. The Name Field will become active and the fi rst zero will be highlighted. Notice that there are now ten placeholders for alpha-numeric characters displayed.
16 Getting Started Y ou should now have enough knowledge to navigate through the main pages, Option Menus and enter data into your GPSMAP 76. Now let’ s learn how to navigate! The main use of a GPS is to be able to navigate to a known position. W e have already created a waypoint and named it CREEK.
17 Getting Started Going to a waypoint: 1. Press the NA V Key . 2. Highlight ‘Go To P oint’ then press the ENTER Ke y. 3. Highlight ‘W aypoints’ then press the ENTER Ke y. 4. Highlight ‘MAP 1’ then press the ENTER Ke y. 5. Highlight the Goto Button then press the ENTER Ke y.
18 Getting Started Press the ROCKER Key to the left simulating a left turn, until the Pointer is realigned with the vertical line in the Compass Ring. Y ou are now headed toward the waypoint.
19 Getting Started Before we take of f walking lets clear the T rack Log. The T rack Log is the bread crumb trail left on the Map Page and Highway Page. T o clear the T rack Log: 1 Press the MENU K ey twice to display the Main Menu. 2. Highlight T racks then press the ENTER K ey .
20 Getting Started Start walking, as you move you will see that the Pointer is pointed at your destination. As soon as you are able, turn toward the Pointer until it is aligned with the vertical line in the Compass Ring. Continue walking, as you approach your HOME waypoint a message will be displayed alerting you that you have arrived.
21 Getting Started 21 The Reference Section of this manual will describe the Main Display Pages and their options in detail. The Getting Started section described the process of navigating the Main Display Pages and the Option Menus.
22 Getting Started 22 Reference Initialization Options If the GPSMAP 76 is unable to determine its location’, an options menu will be displayed. Depending on the situation, select an option to help the unit acquire satellites. T o select an option, place the highlight over the option then press ENTER .
23 Getting Started 23 Reference GPS Information Page The GPS Information Page displays your speed, elevation, the estimated accuracy , receiver status, satellite locations, satellite signal strength, the date, time and the GPS receiver’ s current location.
24 Getting Started 24 Reference Satellite Location The location of each available satellite is displayed over two location rings. The outer ring represents the horizon, the inner ring r epresents 45° above the horizon and the center represents dir ectly overhead.
25 Getting Started 25 Reference GPS Information Page Options Menu T o activate the Options Menu from the GPS Information Page, press the MENU Key . T o select an option, highlight the desired selection then press ENTER . Start/Stop Simulator — This option is used to Start or Stop the Simulator .
26 Getting Started 26 Reference Map Page The GPSMAP 76 comes with a built-in basemap of North America that includes a database of Cities, Interstate, State and County Highways, Exit infor - mation, Lake and River outlines and Railway Lines. The standard basemap can be enhanced using GARMIN’ s MapSource pr oducts.
27 Getting Started 27 Reference Show Next Street — This option adds a window below the Data Fields that will display the name of the next cross str eet. This will only function if ‘Lock to Road’ is ‘On’ (see Setup Map — ‘Other’T ab on page 33) and MapSource Metroguide or City Navigator data is loaded in the unit.
28 Getting Started 28 Reference • Zoom Setting — This setting determines when items will be displayed on the map. Y ou have the option of selecting ‘Off ’, ‘Auto’ or a ‘Zoom’ Scale that coincides with the Zoom Scales for the map. If you select ‘Off ’, the items for that option will not be displayed on the Map Page.
29 Getting Started 29 Reference Colors — This option gives you the ability to confi gure the map to display either land or water as white. If you select ‘Land’ the land portion of the display will be lighter in color than the water . If you select ‘W ater’ the water portion of the display will be lighter in color than the land.
30 Getting Started 30 Reference Setup Map — ‘Waypoint’ T ab The ‘W aypoint ‘ T ab contains the W aypoint, and Active Route W aypoint option settings. Each of the options has a ‘T ext’ and ‘Zoom’ setting. T o change a setting, highlight the appropriate fi eld then press ENTER .
31 Getting Started 31 Reference Setup Map — ‘Line’ T ab The ‘Line’ T ab contains the ‘Zoom’ scale settings for T rack Log, Saved T racks, Active Route, and a ‘Off/On setting for the Bearing Line. T o change a setting, highlight the appropriate fi eld then press ENTER .
32 Getting Started 32 Reference Metro — Metropolitan ar eas will appear as a shaded area. Setup Map — ‘T opo’ T ab The ‘T opo’ T ab contains the ‘T ext’ and ‘Zoom’ settings for Major Contour , Intermediate Contour , and Minor Contour Lines.
33 Getting Started 33 Reference Setup Map — ‘Other’ T ab The ‘Other’ T ab contains the ‘T ext’ and ‘Zoom’ settings for Railroad and a On/Off setting for the Accuracy Cir cle. T o change a setting, highlight the appropriate fi eld then press ENTER .
34 Getting Started 34 Reference Pointer Page Options T o access the Pointer Page Options, with the Pointer Page displayed press the MENU Key . Setup P age Layout — This option allows you to select the number of data fi eld rows and the size of text used in the fi elds.
35 Getting Started 35 Reference Highway Page Options T o access the Highway Page Options, with the Highway Page displayed press the MENU Key . T o select an option from the Menu, highlight the desired selection then press ENTER . Setup P age Layout — This option allows you to select the text size and the number of data fi elds rows.
36 Getting Started 36 Reference Active Leg — If ‘Off ’ is selected, the Active Leg of the Graphic Highway will not be displayed. Active Route — If ‘Off ’ is selected, the Graphic Highway will not be displayed. T rack Log — If ‘Off ’ is selected, the T rack Log will not be displayed.
37 Getting Started 37 Reference Main Menu Page The Main Menu Page contains settings and features that are not on the Main Pages. The Main Menu can be accessed from any of the Main Pages by pr essing MENU twice. T o select an item on the Main Menu, place the highlight over the menu item then press ENTER .
38 Getting Started 38 Reference T rip Computer Options T o access the T rip Computer Options, with the T rip Computer displayed, press the MENU Key . T o select an option, highlight the desired option then press ENTER . Reset T rip — This option will reset all data fi elds except max speed and odometer to zero.
39 Getting Started 39 Reference • Record — ‘Of f ’, ‘W rap When Full’ or ‘Stop When Full’. If ‘W rap When Full’ is selected, when track memory is full, the oldest track point will be deleted and a new point added at the end.
40 Getting Started 40 Reference Points P age The Points Page allow you to select W aypoints, Points of Interest, Cities, Exits, Addresses, and Intersections using your current location or a location on the map. T o select a Point item, highlight the desired selection then press ENTER .
41 Getting Started 41 Reference Points Of Inter est W ill only be avainable when MapSource CD data that contains Points of Interest information is loaded in the unit. When ‘Points of Interest’ is selected, the Points of Interest Selection Page is displayed.
42 Getting Started 42 Reference Cities When ‘Cities’ is selected, a list of cities is displayed with the nearest city listed fi rst. If you press MENU, you will have the option of fi nding a city by name or showing a list of the nearest cities.
43 Getting Started 43 Reference After you have selected an Exit Option, a list will be displayed. T o view information about a specifi c item, highlight the item then press ENTER . A Page containing information about the item will be displayed. T o begin direct navigation to the item, highlight the ‘Go Exit’ Button then press ENTER .
44 Getting Started 44 Reference Intersections This option will only be available when MapSource CD data that contains intersections is loaded in the unit. When ‘Intersection’ is selected, the Find Intersection Page is displayed. T o fi nd an Intersection, you must enter the First and Second street names.
45 Getting Started 45 Reference Routes A Route is a series of waypoints used for point to point navigation. A route must have at least two waypoints, a start and fi nish, but can contain as many as fi fty .
46 Getting Started 46 Reference Create Route Options Use Map — This displays the Map Page with the Map Pointer active. Y ou can now point at any location or point on the map, and enter it into the route. When using the Map to create a r oute, you can select an existing User W aypoint/Map Feature, or you can create a ‘New’ W aypoint.
47 Getting Started 47 Reference Naming the Route — the GPSMAP 76 will automatically name the route using the fi rst and last waypoint names as a reference. T o change the Route Name, place the highlight over the Name fi eld then press ENTER . When you have fi nished, press ENTER to save the new name.
48 Getting Started 48 Reference 2. Place the Map Pointer over a location that is not a Map Feature then press ENTER. The New waypoint Page will be displayed, press ENTER to save the new waypoint. Place the Map Pointer over the route leg that you want to insert the waypoint into then press ENTER.
49 Getting Started 49 Reference Plan Route — T o plan a route, enter a Speed, Fuel Flow , Depart Time and Depart Date. Fuel Flow is measured in “units per hour” it may be necessary to consult your vehicles Owner’ s Manual for performance specifi cations.
50 Getting Started 50 Reference Celestial The Celestial Menu let’ s you view information for Tides, Sun and Moon , or Hunt and Fish. Tides — Displays a graphical chart which displays tide station information in a 24 hour span starting at midnight station time.
51 Getting Started 51 Reference Hunt and Fish Page Main Menu Celestial The top of the page will display the date being referenced with the tide station being referenced, below . The top of the chart will show a 24-hour block of local time (LCL) for your position, with the reported station time (ST A) appearing at the bottom.
52 Getting Started 52 Reference Sun and Moon — The Sun and Moon Page displays data for Sunrise/Sunset, Moonrise/Moonset, and the approximate location of the Sun and Moon on a skyview . The moon phase will display the current visible portion of the moon in a light color .
53 Getting Started 53 Reference Main Menu MapSource Info MapSource Info The MapSource Info Page displays a list of the MapSour ce data stored in the unit and description of the highlighted list item. Y ou can choose to ‘Show’ the data on the map, by placing a checkmark in the ‘Show’ Box.
54 Getting Started 54 Reference ‘Battery Saver’ — When ‘Battery Saver’ is selected, the receiver is optimized to save battery power . When in the Battery Saver mode you may experience slower screen updates, but should notice a signifi cant increase in battery life.
55 Getting Started 55 Reference Setup Menu — ‘Time’ T ab The ‘T ime’ T ab contains settings for Time Format, T ime Zone, Daylight Sav- ings time, Current Date, and Current T ime. T o change a setting highlight the fi eld then press ENTER . Make your selection then press ENTER to activate the selection.
56 Getting Started 56 Reference Setup Menu — ‘Units’ T ab The ‘Units’ T ab contains settings for Elevation, Depth, Distance and Speed, T emperature, Direction Display , and Speed Filter . These settings are used in related fi elds throughout the unit.
F F 57 Getting Started 57 Reference ‘Map Datum’ — Datums are used to describe geographic positions for survey- ing, mapping, and navigation and are not actual maps built in the unit.
58 Getting Started 58 Reference Setup Menu — ‘ Alarms’ Tab The ‘Alarms’ T ab contains settings for Anchor Drag, Approach and Arrival, Of f Course, Shallow W ater , and Deep W ater . These settings will determine if, and when an warning beep is sounded and/or a message is displayed.
59 Getting Started 59 Reference Setup Menu — ‘Interface’ T ab The Interface T ab contains one fi eld, ‘Serial Data Format’. This fi eld contains eight settings that allow the GPSMAP 76 to communicate with computer softwar e and other electronic devices.
60 Getting Started 60 Appendix A Physical Specifi cations Size: 1.3”x2.7”x6.2” W eight: 7.5 ozs (??kg) Display: 2.9" diagonal (6.0cm) high-contrast, 4-level gray LCD with backlighting (180 x 240 pixels) Case: Fully gasketed, fl oatable, high-impact plastic alloy , waterproof to IEC 529-IPX-7 T emp.
Connecting the Power/Data The power/data cable connects the GPSMAP 76 to a 8-35 volt DC system and provides interface capabilities for connecting external devices. The color code in the diagram below indicates the appropriate harness connections. Replacement fuse is a AGC/3AG - 2.
The chart below gives an approximate UTC (Universal T ime Coordinate) time offset for the various longitudinal zones. Check with local charts for mor e detailed information. If you are in daylight savings time, add one hour to the of fset. Longitudinal Zone Offset W180.
Adindan Adindan- Ethiopia, Mali, Senegal, Sudan Afgooye Afgooye- Somalia AIN EL ABD ‘70 AIN EL ANBD 1970- Bahrain Island, Saudi Arabia Anna 1 Ast ‘65 Anna 1 Astro ‘65- Cocos I.
Midway Ast ‘61 Midway Astro ‘61- Midway Minna Minna- Nigeria NAD27 Alaska North American 1927- Alaska NAD27 Bahamas North American 1927- Bahamas NAD27 Canada North American 1927- Canada and Newfoundland NAD27 Canal Zone North Am. 1927- Canal Zone NAD27 Caribbn North American 1927- Caribbean (Barbados, Caicos Islands, Cuba, Dom.
65 Getting Started 65 Appendix E Navigation T erms Elevation— Height above mean sea level (MSL). A vg Speed— The average of all second-by-second speed readings since last reset. Bearing (BRG)— The compass direction fr om your current location to a destination.
66 Getting Started 66 Odometer— A running tally of distance travelled, based upon the distance between second-by-second position readings. Off Course— The distance you are of f a desired course in either direction, left or right. Also referred to as ‘cr oss-track error’ or ‘course error’.
67 Getting Started 67 Cannot display all found, use city or postal code — The unit found too many items to display . Narrow the sear ch using the city or postal code. Dragging Anchor — is the message displayed when the distance set in the Anchor Alarm is exceeded.
68 Getting Started 68 Shallow W ater — The water is shallower than the amount set in the Shallow W ater Alarm. T rack Already Exists — A saved track with the same name already exists. T rack Memory Full — No more track data ca be stored without deleting old data.
Loran TD System LORAN C is a radio navigation aid operated and maintained in the United States by the United States Coast Guard. The name LORAN is an acr onym for “LOng RAnge Navigation”. The LORAN system covers the entire United States and the U.
The LORAN Position Format fi eld is located under the Units tab in the Main Menu. The ‘LORAN TD Setup’ window contains the fi elds to select the Loran GRI-Chain Number , Primary and Secondary Stations, and TD Offsets. T o setup Loran TD from the Main Menu: 1.
71 Getting Started 71 Appendix H Accessories Standard Accessories Owner’ Manual Part No. 190-00230-00 Quick Reference Guide Part No. 190-00230-01 Lanyard Part No. 013-00052-00 Pr ovides convenient method for carrying the GPSMAP 76. Optional Accessories Automotive Mounting Bracket Part No.
C Capabilities .............................................. 4 Cautions ................................................... 2 Celestial Page Settings ....................... 50-52 Changing Data Fields ............................... 7 Cities. .......
E Editing W aypoints ............................ 14, 15 ENTER Key ............................................ 10 Exits. ................................................. 42-43 F Follow T rack (T racBack) .......................... 39 Follow Route ..
Map Page .................................... 11, 26-27 Map Page Layout .................................... 26 Map Page Options ............................ 26-33 Map Pointer ........................................... 16 Map Scales .................
Route List Page ....................................... 45 Routes .............................................. 45-49 Routes- Activating .................................. 45 Routes- Copying ..................................... 45 Routes- Creating .
T ime, Daylight Savings ........................... 55 T imers, T rip ............................................ 37 T racBack .................................................. 39 T rack Log- Clearing .......................... 19, 38 T rack Log- Deleting .
77 Getting Started 77 Appendix J W arranty LIMITED W ARRANTY GARMIN Corporation warrants this product to be fr ee from defects in materi- als and manufacture for one year fr om the date of purchase. GARMIN will, at its sole option, repair or replace any components that fail in normal use.
190-00230-00.indd 03/15/01, 9:26 AM 78.
© 2001 GARMIN Corporation GARMIN International, Inc. 1200 East 151 st Street, Olathe, Kansas 66062, U.S.A. GARMIN (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey , SO51 9AQ, U.K. GARMIN Corporation No. 68, Jangshu 2 nd Road.
デバイスGarmin GPSMAP 76の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Garmin GPSMAP 76をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGarmin GPSMAP 76の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Garmin GPSMAP 76の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Garmin GPSMAP 76で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Garmin GPSMAP 76を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGarmin GPSMAP 76の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Garmin GPSMAP 76に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGarmin GPSMAP 76デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
