GBCメーカーUSP 13の使用説明書/サービス説明書
ページ先へ移動 of 17
USP 13 UNIVERSAL SPEED PUNCH Operator Manual.
USP 13 UNIVERSAL SPEED PUNCH Operator Manual T able of Contents Operating Instructions 1 Service and Maintenance Agreement 2 Selecting Knife Set Up 3 Installation of Punching Die 4 Set Up Instructions.
USP 13 Universal Speed Punch Operating Instructions The Universal Speed Punch from GBC Automated Finishing Division is specially designed to punch various weight paper sheets and cover stock. The machine has a variable speed control which can be adjusted from 70-110 cycles per minute.
Service And Equipment Maintenance Agreement By purchasing the USP 13 you have invested in a highly capable punching machine that will give you years of r eliable service. T o help protect this investment be certain to take advantage of the GBC Equipment Maintenance Agr eement (EMA).
3 SELECTING KNIFE SET -UP 1. T ur n power off. 2. Cycle the machine with the hand wheel until the claw reaches between 10 and 11 o’clock. (Figur e 2) 3. Cam #115 sets when the separating knife will go into the stack. Adjust the cam so that the tip of the knife is about 1/8” (.
USP 13 Installation of Punching Dies Using Quick Release Die Clamp Assembly When installing a punching die, be sure that the lower die support is wiped clean of dirt and paper chips. The bottom of the die itself should be cleaned likewise. Wiping the top and bottom of the die with a thin coating of oil is advisable.
5 USP 13 SET -UP INSTRUCTIONS: After the punching die is properly installed, position the back gauge rail (#108, Figure 7) slightly ahead of the punch die back gauge so that a piece of paper can slide freely into the thr oat of the die and not hit the back gauge of the punch die.
111 170 83 127 1.0 Figure 10 Figure 12 CLA W THESE SURF ACES TO BE IN LINE 46 Place a sheet of paper against pusher (#111) in its home position (rear). Install the thr ee paper support straps (#127 & #83, Figure 10) 1” away fr om the edge of the paper .
7 Position front (#49) and r ear (#56 & #48) supply stack guides so that the posts clear the paper stack by about 1/16”. A stack of 2 to 3 inches is requir ed. Locate adjustable stack guide post (#59) so that the post is in line with the separating knife.
USP 13 Universal Speed Punch QUICK REFERENCE INSTRUCTIONS 1. DIE REPLACEMENT BLOCK UP DIE WITH STICK PROVIDED LOWER DIE CLAMP STICK REMOVE DIE CLAMPS - FRONT & REAR REMOVE BOTTOM BOL TS RELEASE CL.
9 It is recommended that the machine be lubricated once every two weeks. Lubricate by putting a few drops of machine oil in the lubricating holes, which are marked with red paint. All gears in the main body of the machine run in pans, which are partially filled with a special gear lubricating grease.
10 GENERAL RULES FOR GRINDING PUNCHING PINS OF PUNCHING TOOLS IT IS ALSO NECESSAR Y TO SHARPEN THE FEMALE PORTION (BOTTOM PLA TE) OF THE PUNCHING TOOL. SURF ACE GRIND THE TOP OF THE BOTTOM PLA TE UNTIL THE EDGES OF THE HOLES ARE SHARP . THIS WILL REQUIRE APPROXIMA TEL Y .
11 USP 13 OPTIONS & ACCESSORIES 1. Short Sheet Assembly 2. Front and Rear Cradle Bracket Assemblies 3. Long Small Roller Assembly 4. Stack Guider Adaptor 5. Auxiliary Pusher Optional assemblies that can be purchased separately include: 1. Small Roller Assembly 2.
12.
13 016509000 LONG SMALL ROLLER ASSEMBL Y The Long Small Roller Assembly is used when the standard Large Roller Assembly does not allow enough reach to grab a lift of paper when it is fully jogged.
14.
General Binding Corporation Northbr ook, Il 60062-4195 http://www .GBC.com PN 0165999900 Rev B.
デバイスGBC USP 13の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
GBC USP 13をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGBC USP 13の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GBC USP 13の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GBC USP 13で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GBC USP 13を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGBC USP 13の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GBC USP 13に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGBC USP 13デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
