GEメーカーJKP27の使用説明書/サービス説明書
ページ先へ移動 of 12
Before you begin Read these instructions carefully and completely • IMPORT ANT -Save these instructions for local inspector ’ s use. • IMPORT ANT -Observe all governing codes and ordinances. • Note to Installer- Be sure to leave these instructions with the consumer .
• Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury .
Installation Instructions EASY INSTALLATION OF YOU NEW 30" WALL OVEN Before you begin-Read these instructions completely and carefully. IMPORTANT- Save these instructions for local inspector's use. IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.
Pre- Installation Checklist cont. Place the oven on a table or platform even with the cutout opening. (Platform must support 150 lbs. single, 275 lbs. double.) 4 Remove the bottom trim from the top of the oven. It will be installed at the end of installation.
5 Cutouts for Single Built-In-Oven A1 Installation Instructions Cabinet Wid t h 27 Recommended Cutout Location from Floor 32 1/2” Cutout Depth 23 1/2” Cutout Wid t h 25” Min.
NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” thick, shim both sides equally to establish the cutout width. Cutouts for Double Built-In-Oven A2 6 Cabinet Wid t h 27” Recommended Cutout Location from Floor 13 1/4” Cutout Depth 23 5/8” Min.
NOTE: This Oven is not approved to be installed under a Solid Disk, Induction or Downdraft Modular Cooktop. Cutout s for Single Oven Under Counter A3 Installation Instructions 7 25" Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size.
8 T urn off the circuit breaker or remove fuses to the oven branch circuit. With the oven in front of the cabinet opening, on a table or platform, connect the flexible conduit to the electrical junction box as shown below . Y ou will need to purchase a strain relief clamp to complete the connection of the conduit to the junction box.
OR Three-Conductor Branch Circuit Connection When connecting to a 3-conductor branch circuit, if local codes permit: Junction Box Cover a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using wire nut.
b. Lift oven into cabinet cutout using the oven opening as an grip. Carefully push against oven front frame. Do not push against outside edges. c. As you slide the oven back, pull the string so that the conduit will lie on top of the oven in a natural loop.
D1 D2 D3 D4 D5 The oven door is heavy . Y ou may need help lifting the door high enough to slide it into the hinges slots. Do not lift the door by the handle. 11 Replacing the Oven Door D Inst allation Instructions Pick the Oven Door up by placing one hand on each side.
12 Installation Instructions Pub. No. 31-10473 229C 4053P452 PRE-TEST CHECK LIST E Remove all protective film if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 10).
デバイスGE JKP27の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE JKP27をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE JKP27の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE JKP27の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE JKP27で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE JKP27を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE JKP27の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE JKP27に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE JKP27デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。