GEメーカーJTP20の使用説明書/サービス説明書
ページ先へ移動 of 16
1 30 ” Built-In W all Oven Installation Instructions JTP20, JTP25, JTP28, JTP48, JTP50, JT912, JT915, JT952, JT955, ZET938, ZET958 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before Y ou Begin Read these instructions carefully and completely .
2 Electrical Requirements This appliance must be supplied with the proper voltage and frequency , and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating plate is located on oven frame.
3 Open oven door and remove literature pack, broiler pan and grid, and oven racks. Remove Installation Instructions from literature pack and read them carefully before you begin. Be sure to place all literature, Owner ’s Manual, Installations, etc. in a safe place for future reference.
4 Place the oven on a table or platform even with the cutout opening. (Platform must support 150 lbs. single, 275 lbs. double.) Installation Instructions Pre-Installation Checklist cont. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process.
5 Cabinet Width 30 ” Recommended Minimum Cutout Location from Floor 32 1/2 ” Cutout Depth 23 1/2 ” Min. Cutout Width 28 1/2 ” Min. 28 5/8 ” Max.
6 Installation Instructions Cabinet Width 30 ” Recommended Minimum Cutout Location from Floor 12 ” Cutout Depth 23 1/2 ” Min. Cutout Width 28 1/2 ” Min.
7 Installation Instructions Cutout for Single Built-In Oven Under Counter NOTE: This oven is not approved to be installed under a solid disk, induction or downdraft modular cooktop. A3 25" Gas or electric cooktops may be installed over this oven.
8 (Continued on following page) Installation Instructions Electrical Connections ATTENTION INST ALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible conduit.
9 Installation Instructions Electrical Connections cont. B4 Three-Conductor Branch Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
10 (Continued on following page) W ARNING: Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet causing serious injury . Installation Instructions Securing the Oven in the Opening Drilling the Pilot Holes and Mounting the Oven a.
11 a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template, mark the center of each slot (two total) where the mounting holes will be drilled. c. Remove the trim. d. Drill pilot holes into the center of each template mark.
12 Lift the oven door by placing one hand on each side. The door is heavy , so you may need help. Do not lift the door by the handle. With the door at the same angle as the removal position (half way between the closed and broil stop position, seat the notch of the hinge arm into the bottom edge of the hinge slot.
13 Installation Instructions Remove all protective film, if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Pre-T est Checklist Check that the bottom trim is installed properly (see page 1 1).
14 NOTES.
15 NOTES.
16 NOTES.
デバイスGE JTP20の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE JTP20をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE JTP20の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE JTP20の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE JTP20で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE JTP20を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE JTP20の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE JTP20に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE JTP20デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。