GEメーカーJVM1790の使用説明書/サービス説明書
ページ先へ移動 of 24
Questions? Call 1-800-361-3400 or Visit our W ebsite at: geappliances.ca READ CAREFULL Y . KEEP THESE INSTRUCTIONS . Read these instr uctions completely and carefully . • IMPORT ANT – Save these instructions for local inspector’ s use. • IMPORT ANT – Obser ve all governing codes and ordinances.
2 Recirculating ........................................ 19–22 Attach Mounting Plate to W all ............19 Preparation of T op Cabinet ................19 Adapting Blower for Recirculation ..........................20, 21 Mount the Oven ...........
This product requires a three-prong grounded outlet. The installer must per form a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded.
4 EQUIV ALENT NUMBER EQUIV ALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) (6”/15.2 cm Round) Rectangular -to-Round 5 Ft. (1.5 m) x (1) = 5 Ft.
EQUIV ALENT NUMBER EQUIV ALENT DUCT PIECES LENGTH x USED = LENGTH Rectangular -to-Round 5 Ft. (1.5 m) x ( ) = Ft. or m T ransition Adaptor* Wall Cap 40 Ft. (12.2 m) x ( ) = Ft. or m 90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m 45° Elbow 5 Ft. (1.5 m) x ( ) = Ft.
PA R T QUANTITY T op Cabinet 1 T emplate Rear Wall 1 T emplate Installation 1 Instructions Separately 2 Packed Grease Filters P ART QUANTITY Wood Screws 2 ( 1 ⁄ 4 “ x 2“) T oggle Bolts (and 4 wi.
7 TOOLS YOU WILL NEED #1 and #2 Phillips screwdriver Pencil Ruler or tape measure and straight edge Carpenter square (optional) T in snips (for cutting damper , if required) Electric drill with 3 ⁄ .
8 Find the studs, using one of the following methods: A. Stud finder – a magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting sur face to find a solid sound. This will indicate a stud location. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud.
9 DETERMINING W ALL PLA TE LOCA TION UNDER YOUR CABINET C. Y our cabinets may have decorative trim that inter feres with the oven installation. Remove the decorative trim to install the oven properly and to make it level. THE OVEN MUST BE LEVEL. Use a level to make sure the cabinet bottom is level.
10 ALIGNING THE W ALL PLA TE Draw a vertical line on the wall at the center of the 30 ″ (76.2 cm) wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cabinets with front overhang.
A INST ALLA TION TYPES (Choose A, B or C) This oven is designed for adaptation to the following 3 types of ventilation: A. Outside T op Exhaust (V er tical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-V ented Ductless) NOTE: This oven is shipped assembled for Outside T op Exhaust.
Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw , make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet.
13 3 MOUNT THE OVEN A4. USE TOP CABINET TEMPLA TE FOR PREP ARA TION OF TOP CABINET Y ou need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor . A2. FOR EASIER INST ALLA TION AND PERSONAL SAFETY , WE RECOMMEND THA T TWO PEOPLE INST ALL THIS OVEN.
14 4 Attach the oven to the top cabinet. 8 7 6 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of the oven. (While tightening screws, hold the oven in place against the wall and the top cabinet.
INST ALLA TION OVERVIEW B1. Prepare Rear W all B2. Attach Mounting Plate to W all B3. Prepare T op Cabinet B4. Adjust Blower B5. Mount the Oven Installation Instructions 15 PREP ARING THE REAR W ALL FOR OUTSIDE BACK EXHAUST B1. Y ou need to cut an opening in the rear wall for outside exhaust.
16 USE TOP CABINET TEMPLA TE FOR PREP ARA TION OF TOP CABINET B3. • Read the instructions on the TOP CABINET TEMPLA TE. • T ape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLA TE. CAUTION: W ear safety goggles when drilling holes in the cabinet bottom.
17 Installation Instructions Snip all 4 webs on each knockout panel and remove the metal knockouts for rear airflow . Locate the two “knockout” plates, on the rear oven panel, near the top of the oven. Using tin snips, carefully cut the web area from the two holes side-by-side (that secure the knockouts to the oven).
Attach the oven to the top cabinet. 18 Installation Instructions 3 MOUNT THE MICROW A VE OVEN B5. FOR EASIER INST ALLA TION AND PERSONAL SAFETY , WE RECOMMEND THA T TWO PEOPLE INST ALL THIS MICROW A VE OVEN. IMPORT ANT: Do not grip or use handle during installation.
USE TOP CABINET TEMPLA TE FOR PREP ARA TION OF TOP CABINET C2. 19 INST ALLA TION OVERVIEW C1. Attach Mounting Plate to W all C2. Prepare T op Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter (not supplied) • Read the instructions on the TOP CABINET TEMPLA TE.
20 Installation Instructions AFTER: Fan Blade Openings Facing Forward 3 2 4 ADAPTING BLOWER FOR RECIRCULA TION C3. NOTE: The exhaust adaptor with damper is not needed for recirculating models. Y ou may want to save them for possible future use. Carefully pull out the blower unit.
21 Attach the oven to the top cabinet. Cabinet Front Cabinet Bottom Shelf Filler Block Oven T op Equivalent to Depth of Cabinet Recess Installation Instructions 3 MOUNT THE OVEN C4. FOR EASIER INST ALLA TION AND PERSONAL SAFETY , WE RECOMMEND THA T TWO PEOPLE INST ALL THIS OVEN.
5 MOUNT THE OVEN (continued) C5. 22 Installation Instructions 8 7 6 Tighten the outer two screws to the top of the oven. (While tightening screws, hold the oven in place against the wall and the top cabinet.) Insert 2 self-aligning screws ( 1 ⁄ 4 ”-28 x 3 1 ⁄ 4 ”) through outer top cabinet holes.
KEEP INST ALLA TION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE. Plug power cord into a dedicated 15 to 20 amp electrical outlet. 7. Read the Owner’ s Manual. 6. Replace house fuse or turn breaker back on. 4. Remove all packing material from the oven.
49-40453 (06-05 JR) Printed in Korea 24.
デバイスGE JVM1790の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE JVM1790をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE JVM1790の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE JVM1790の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE JVM1790で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE JVM1790を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE JVM1790の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE JVM1790に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE JVM1790デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。