GEメーカーPDW9200の使用説明書/サービス説明書
ページ先へ移動 of 12
Installation Instructions Built-In Dishwasher If you have questions, call 800-GECARES or visit our website at: www .GEAppliances.com READ CAREFULL Y . KEEP THESE INSTRUCTIONS.
Installation Preparation P ARTS SUPPLIED: T wo #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop or sides of cabinetry . (T aped to top or side of dishwasher .) Side and top trim pieces T rim Panel Accessory Kit (not shown).
Installation Preparation 3 PREP ARE DISHW ASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 24" wide and approximately 34-1/2" high from floor to underside of the countertop. • The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage.
Installation Preparation 4 For models equipped with power cord: Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified technician. Cabinet Preparation & Wire Routing • The wiring may enter the opening from either side, rear or the floor within the shaded area.
Installation Instructions 5 Figure G STEP 1 CHECK DOOR BALANCE • With dishwasher on the wood skid, check the door balance by opening and closing the door . • If the door drops when released, increase the spring tension. If the door rises when released, decrease the tension.
Installation Instructions 6 • Do not over tighten 90 ° elbow , water valve bracket could bend or water valve fitting could break. • Position the end of the elbow to face the rear of the dishwasher . STEP 5 INST ALL 90 ° ELBOW • W rap 90 ° elbow with thread seal tape.
Power Cord (If Used) Water Line House Wiring Drain Hose Insulation Blanket Installation Instructions 7 STEP 9 INST ALL TRIM PIECES Skip this step if trim is not supplied with the dishwasher . • Locate trim strips inside dishwasher . • Press trim onto the tub flange on each side.
STEP 10 POSITION DISHW ASHER UNDER COUNTER TOP • Push the dishwasher into the cabinet. • Push at the sides with your hands. Do not use your knee against the door since door damage will occur . • Check that the tub insulation blanket does not get “ bunched-up ” or interfere with the springs as you slide it into the cabinet.
Figure X STEP 1 1 LEVEL DISHW ASHER IMPOR T ANT – Dishwasher must be level for proper dish rack operation and wash performance. TIP: Pull lower rack out, about halfway . Check to be sure the rack does not roll forward or back into dishwasher . If the rack rolls in either direction, the dishwasher must be leveled again.
Installation Instructions 10 STEP 13 CONNECT W A TER SUPPL Y Connect water supply line to 90 ° elbow . • Slide compression nut, then ferrule over end of water line. • Insert water line into 90 ° elbow . • Slide ferrule against elbow and secure with compres- sion nut.
Installation Instructions 11 Figure HH STEP 16 PRE-TEST CHECK LIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty . Check to be sure power is OFF . Open door and remove all foam and paper packaging.
Installation Instructions • Align the toekick with the bottom edge and make sure it is against the floor . • Insert and tighten the two toekick attachment screws. The toekick should stay in contact with the floor . TIP: Make sure toekick is against floor to minimize noise.
デバイスGE PDW9200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE PDW9200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE PDW9200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE PDW9200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE PDW9200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE PDW9200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE PDW9200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE PDW9200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE PDW9200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。