GEメーカーTRIVECTION JT930の使用説明書/サービス説明書
ページ先へ移動 of 16
1 31-10663 1-07 JR Installation 30” Built-In T rivection ™ Instructions W all Oven JT930, JT980, ZET3038, ZET3058 BEFORE YOU BEGIN Read these instructions completely and carefully . • IMPOR T ANT — Save these instructions for local inspector’ s use.
2 Installation Instructions PREP ARE TO INST ALL THE OVEN TOOLS YOU WILL NEED MA TERIALS YOU MA Y NEED Wire Nuts Junction Box 60” of String for Single Ovens 96” of String for Double Ovens Adjustab.
3 Installation Instructions PRE-INST ALLA TION All installation information on the following pages is to be used for SINGLE and DOUBLE oven installation! Remove packaging materials. Check behind hinges. Remove plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad.
4 Installation Instructions SINGLE BUIL T -IN OVEN CUTOUT OPTIONS W ALL MOUNT—SINGLE BUIL T -IN OVEN OPTION Cabinet Width 30” Recommended Cutout Location from Floor 32 1/2” Cutout Depth 23 1/2” Min. Cutout Width 28 1/2” Min. 28 5/8” Max. Cutout Height 27 1/4” Min.
Installation Instructions W ALL MOUNT—SINGLE BUIL T -IN OVEN BELOW AN ADV ANTIUM OVEN OPTION • When installed over a single wall oven, allow at least 2” between the two openings. This separation will provide clearance for bottom overlap of the Advantium oven and top overlap of the single wall oven.
6 UNDER COUNTER—SINGLE BUIL T -IN OVEN OPTION D T op and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely , since they will anchor the oven in the cabinet. 25” 24” 27 1/4” Min.
Installation Instructions 7 DOUBLE BUIL T -IN OVEN CUTOUT CUTOUT FOR DOUBLE BUIL T -IN OVEN Cabinet Width 30” Recommended Cutout Location from Floor 12” Cutout Depth 23 1/2” Min. Cutout Width 28 1/2” Min. 28 5/8” Max. Cutout Height 51 13/16” Min.
ON DOUBLE W ALL OVEN MODELS, REMOVE THE LOWER DOOR ONL Y (CONT .): Close door to the door removal position, which is halfway between the broil stop position and fully closed.
Installation Instructions 9 9 ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency , and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate.
10 Installation Instructions ELECTRICAL CONNECTIONS (CONT .) CONNECT CONDUIT With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below . Position the conduit in such a manner that it will lie behind the oven in a natural loop when the oven is installed.
11 Installation Instructions THREE-CONDUCTOR BRANCH CIRCUIT CONNECTION When connecting to a three-conductor branch circuit, if local codes permit: Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
12 Installation Instructions SECURE THE OVEN IN THE OPENING SLIDE THE OVEN INTO THE OPENING Loop (do not tie) the correct length of string around the conduit before the oven is slid into place. This will keep the conduit from falling improperly behind the oven.
13 Installation Instructions T o install a single metal bottom trim assembly (on some models), see Step 11. T o install a metal bottom trim with a plastic bottom trim (on some models), see Steps 11 and 12. INST ALL THE MET AL BOTTOM TRIM With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening.
14 Installation Instructions REPLACE THE LOWER OVEN DOOR ON DOUBLE W ALL OVEN MODELS ON DOUBLE W ALL OVEN MODELS, REPLACE THE LOWER DOOR: Firmly grasp both sides of the door at the top. With the door at the same angle as the removal position, seat the indentation of the hinge arm into the bottom edge of the hinge slot.
15 Installation Instructions FINAL CHECKLISTS PRE-TEST CHECKLIST Remove all protective film. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see Steps 11 and 12).
16 Printed in the United States.
デバイスGE TRIVECTION JT930の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE TRIVECTION JT930をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE TRIVECTION JT930の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE TRIVECTION JT930の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE TRIVECTION JT930で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE TRIVECTION JT930を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE TRIVECTION JT930の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE TRIVECTION JT930に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE TRIVECTION JT930デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。