GEメーカーZET1の使用説明書/サービス説明書
ページ先へ移動 of 16
1 30 ” Built-In W all Oven Installation Instructions ZET1, ZET2 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before Y ou Begin Read these instructions carefully and completely . • IMPORT ANT —Save these instructions for local inspector ’ s use.
2 IMPORT ANT SAFETY INSTRUCTIONS Installation Instructions For Y our Safety • Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
3 Open oven door and remove literature pack, broiler pan and grid, oven racks, rack supports and a bag with 9 hex nuts. Read Installation Instructions carefully before you begin. Be sure to place all literature, Owner ’s Manual, Installations, etc. in a safe place for future reference.
4 Place the oven on a table or platform even with the cutout opening. (Platform must support 175 lbs. [79 kg] single, 350 lbs. [159 kg] double.) Installation Instructions Pre-Installation Checklist cont. Remove the bottom trim from the top of the oven.
5 Cabinet Width 30 ” (76.2 cm) Recommended Minimum Cutout Location from Floor 32 1/2 ” (82.6 cm) Cutout Depth 23 1/2 ” (59.7 cm) Min. Cutout Width 28 1/2 ” (72.4 cm) Min. 28 5/8 ” (72.7 cm) Max. Cutout Height 27 1/4 ” (69.2 cm) Min. 27 5/16 ” (69.
6 Installation Instructions Cabinet Width 30 ” (76.2 cm) Recommended Minimum Cutout Location from Floor 12 ” (30.5 cm) Cutout Depth 23 1/2 ” (59.7 cm) Min. Cutout Width 28 1/2 ” (72.4 cm) Min. 28 5/8 ” (72.7 cm) Max. Cutout Height 51 13/16 ” (131.
7 Installation Instructions Cutout for Single Built-In Oven Under Counter A3 25" Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.
8 Cabinetry NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the W arming Drawer location do not obstruct the required interior 23 1/2 ” (59.7 cm) depth and 9 1/4 ” (23.5 cm) height. • These Monogram Ovens require 3/4 ” (1.
9 NOTE: The middle rail separating the two openings may need to be larger than the 2 ” (5.1 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.
10 (Continued on following page) Installation Instructions Electrical Connections ATTENTION INST ALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible conduit.
11 Installation Instructions Electrical Connections cont. B6 Three-Conductor Branch Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
12 (Continued on following page) W ARNING: Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet causing serious injury . Installation Instructions Securing the Oven in the Opening Drilling the Pilot Holes and Mounting the Oven a.
13 Installation Instructions Installing the Metal Bottom T rim IMPORT ANT : If this unit is ever removed from the cabinet or the oven is ever pulled out for service, the trim must be removed first or damage to the trim will occur . C4 a. Place the bottom trim between the side trim and against the bottom of the cutout.
14 Lift the oven door by placing one hand on each side. The door is heavy , so you may need help. Do not lift the door by the handle. With the door at the same angle as the removal position, seat the notch of the hinge arm into the bottom edge of the hinge slot.
15 Installation Instructions Remove all protective film, if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. NOTE T O ELECTRICIAN: Y ou must unplug the green wire (near where the long flexible conduit exits the unit) when conducting high-potential testing.
16 Printed in U.S.A..
デバイスGE ZET1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GE ZET1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGE ZET1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GE ZET1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GE ZET1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GE ZET1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGE ZET1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GE ZET1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGE ZET1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。