GefenメーカーGTV-ETH-2-PLCの使用説明書/サービス説明書
ページ先へ移動 of 33
Ethernet Over PLC User Manual www .gefentv .com GTV -ETH-2-PLC.
ASKING FOR ASSIST ANCE T echnical Support : T elephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 T echnical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday PST Write T o: Gefen Inc. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 9131 1 www .
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Panel Layout 5 Sender Panel Descriptions 6 Receiver Panel Layout 7 Receiver Panel Descriptions 8 GefenTV Ethernet Over PLC Software Instal.
Congratulations on your purchase of the GefenTV Ethernet Over PLC. Y our complete satisfaction is very important to us. Gefen TV Gefen TV is a unique product line catering to the growing needs for innovative home theater solutions.
READ THESE NOTES BEFORE INST ALLING OR OPERA TING THE GEFENTV ETHERNET OVER PLC • This device passes all 10/100BASE-T Ethernet network protocols (TCP/ IP , NETBUEI, Microsoft Networking, etc.
3 Features • Supports up to 200 Mbps data transmission rate • Extension of up to 200 feet (60 meters) • Web con fi guration for easy maintenance • Features include IGMP multicast, VLAN, and Q.
4 Front Panel Back Panel T op Panel 1 4 23 T op Panel p 5 6 7 SENDER P ANEL LA YOUT.
5 SENDER P ANEL DESCRIPTIONS 1. Standby Button Pressing this will put the sending unit in standby mode. The unit will not transfer any information to the receiving unit in this mode. T o release standby mode, simply press the button again. 2. Ethernet Input Port Connects to the Ethernet source (i.
6 Front Panel Back Panel T op Panel 1 4 23 T op Panel p 5 7 7 8 9 10 RECEIVER P ANEL LA YOUT.
7 RECEIVER P ANEL DESCRIPTIONS 1. Standby Button Pressing this will put the receiving unit in standby mode. The unit will not transfer any information to the sending unit in this mode. T o release standby mode, simply press the button again. 2. Ethernet Input Port ( 1 through 4) Connects to an Ethernet device (i.
8 How to Connect the GefenTV Ethernet Over PLC Installation of the GefenTV Con fi guration Assistant 1. Insert the included installation CD-ROM into your computer that will be used to con fi gure the GefenTV Ethernet Over PLC. 2. The auto run will begin the installation process.
9 GEFENTV ETHERNET OVER PLC SOFTW ARE INST ALLA TION 5. Close all other applications and press the Next button to continue. 6. Please read the license agreement and click on the I Agree button to continue.
10 7. Please choose the program installation destination. The default location is “C: Program FilesGefen TV Ethernet Over Power Line”. T o set your own destination, click on the browse button and navigate to your preferred location. Click the install button to continue.
11 1. Connect the source (i.e. computer , router , switch) to the GefenTV Ethernet Over PLC sender unit using the supplied CA T -5e cable. 2. Connect the Ethernet devices (i.e. computer , game system, set-top box) to the GefenTV Ethernet Over PLC receiver unit.
12 Once both the sending and receiving units are linked and powered, basic con fi guration can proceed. This section of the manual refers to the sending unit as the LOCAL NODE, and the receiving unit as the REMOTE NODE. NOTE: The following steps are for manual con fi guration of the nodes for a basic secure network.
13 CONFIGURING THE GEFENTV ETHERNET OVER PLC 6. Once all possible nodes have been detected, the program will display all of these nodes as in the window below . The local node that the computer is connected to will appear as the “ETH connected node”.
14 CONFIGURING THE GEFENTV ETHERNET OVER PLC 8. The PLC node con fi guration screen is separated into the following items: NET ID This is the name of the network. This name must be the same for both the local and remote nodes for proper operation. The NET ID can be an ASCII string up to 20 characters long.
15 CONFIGURING THE GEFENTV ETHERNET OVER PLC 9. Once the update is complete, a message will appear to indicate the update was successful. Click on the ok button to continue.
16 CONFIGURING THE GEFENTV ETHERNET OVER PLC 1 1. Once the con fi guration for the remote node is complete, the local node will then have to be con fi gured. Click on the local node which is labeled as the “ETH connected node” and press next to continue.
17 AUTOMA TIC SECURITY CONFIGURA TION FEA TURE T o quickly setup the Gefen TV Ethernet Over PLC for secure use, the Automatic Security Con fi guration Mode (ASCM) can be activated on each node. Follow the below steps to automatically setup a secure connection between multiple nodes.
18 AUTOMA TIC SECURITY CONFIGURA TION FEA TURE 1. Connect the computer with the installed Gefen TV software to the node you wish to set as the Master node. 2. Press and hold the Security/Reset button on the node (ASCM), located on the front panel, for approximately 2 seconds.
19 ADV ANCED CONFIGURA TION There are optional advanced settings that can be con fi gured for each node. The advanced menu can be accessed directly through the main con fi guration page. Click on the MAC address of the node you wish to con fi gure and click on the advanced button to the left of the node listing.
20 ADV ANCED CONFIGURA TION Firmware Update This section is used to update the node’s fi rmware from a server location. Please see the Firmware Update section on page 27 for full details. Upgrade Firmware This section is used to update the node’s fi rmware from a fi le.
21 ADV ANCED CONFIGURA TION MUL TICAST IGMP Multicast This option will enable or disable the node’s ability to transmit IGMP multicast data. SECURITY The security tab will allow the user to adjust the con fi guration password, the encryption password, the network ID, and the alias for the node.
22 ADV ANCED CONFIGURA TION VLAN This option will enable or disable the node’s ability to accept VLAN data. If this feature is enabled on one of the nodes, it must be set on all other for VLAN tag packets to pass. QOS QOS (quality of service) is supported for managing traf fi c between nodes.
23 ADV ANCED CONFIGURA TION ADV ANCED QOS QOS (quality of service) prioritization. Rule 1 will be applied to all packets fi rst and then Rule 2. Prioritization protocols are: 1. UDP is high priority , TCP is low priority 2. TCP is high priority , UDP is low priority 3.
24 WEB CONFIGURA TION If an IP address has been set in the ADV ANCE CONFIGURA TION P ANEL , access to the WEB UTILITY will be enabled. T o access the WEB UTILITY , open your web browser and type the ip address into the address fi eld. The IP address is dependant on the IP Con fi guration Setting assigned on page 20.
25 WEB CONFIGURA TION MAIN P AGE The main page will display general con fi guration information. Clicking on the further information link will navigate to a new page with all the current con fi guration information (see page 26).
26 WEB CONFIGURA TION The con fi guration options are as follows: MAC Con fi guration Network Con fi guration Multicast Con fi guration VLAN Con fi guration Priority Con fi guration (QOS) Securi.
27 FIRMW ARE UPDA TE PROCEDURE The fi rmware for the GefenTV Ethernet Over PLC can be updated by FTP , TFTP , or a direct fi le. The fi rmware update can be executed from either the ADV ANCED CONFIGURA TION P ANEL , or the WEB UTILITY .
28 Standard Support ........................................................ UP A DHS (200 Mbps) PLC Interface .................................... One Power Line port / 4 Ethernet 10/100M Ports Security ...............................................
29 W ARRANTY G e f en warrants the equipment it manu f actures to be f ree f rom de f ects in material and workmanship. I f equipment f ails because o f such de f ects and G e f en is noti fi ed with.
20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefentv.com support@gefentv.com Rev X3.
デバイスGefen GTV-ETH-2-PLCの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gefen GTV-ETH-2-PLCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGefen GTV-ETH-2-PLCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gefen GTV-ETH-2-PLCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gefen GTV-ETH-2-PLCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gefen GTV-ETH-2-PLCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGefen GTV-ETH-2-PLCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gefen GTV-ETH-2-PLCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGefen GTV-ETH-2-PLCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
