Gemini IndustriesメーカーFT-160の使用説明書/サービス説明書
ページ先へ移動 of 17
It is of vital impor tance, bef ore attempting to operate y our engine, to read the general 'SAFETY INSTRUCTIONS AND W ARNINGS' section on pages 2-4 of this booklet and to strictly adhere to the advice contained therein.
2 Remember that your engine is not a " toy ", but a highly efficient internal-combustion machine whose power is capable of harming you, or others, if it is misused or abused. As owner, you, alone, are responsible for the safe operation of your engine, so act with discretion and care at all times.
4 Take care that the glow plug clip or battery leads do not come into contact with the propeller. Also check the linkage to the throttle arm. A disconnected linkage could also foul the propeller. After starting the engine, carry out any needle-valve readjustments from a safe position behind the rotating propeller.
6 ENGINE P AR TS NAME Rock er Cover Glow Plug Lock Nut Drive Hub Propeller W asher Crankcase Carburetor Exhaust Pipe Propeller Nut Cylinder Head Left (No .1) Cylinder Right (No .2) Cylinder Photo . 2 Aluminum tube Aluminum tube is not supplied with the engine.
8 It is essential that the firewall is strong and rigid (e.g. at least 15mm thick) and firmly integrated with the structure of the aircraft. INSTALLATION In the interests of scale appearance, the engine should be installed with the carburetor below the crankcase so that the exhaust pipes point downwards.
10 16x8, 18x6-8, 20x6 Carburetor The needle-valve and throttle lever locations are interchangeable by reversing the carburetor. This can be done as follows: Remove the carburetor carefully by unscrewing the two screws which secure both carburetor and choke valve.
12 GLOWPLUGS The role of the glo wplug Glowplug life Particularly in the case of very high performance engines, glowplugs must be regarded as expendable items. Install a plug suitable for the engine. Use fuel containing a moderate percentage of nitromethane unless more is essential for racing events.
14 Glowplug leads Fig.12 Switch should have sufficient capacity. The plug leads are fitted with special snap-on connectors that ensure firm contact with O.S. plug. They are a "click" fit and are not suitable for use with most other makes of glowplug.
16 Make sure that glowplugs are not connected to the battery. Do not heat the glowplugs while priming. (Fig.15). 2. Fig.15 Do not connect the battery to the glowplugs while priming. Open the throttle valve fully, close the choke valve and turn the propeller counter-clockwise through three revolutions.
18 Adjust the needle-valve 10. Abrupt adjustment of the needle-valve may cause the engine to stop, especially when it is new and insufficiently run-in. As the speed of the engine does not instantly change with needle-valve readjustment, small movements, with pauses between, are necessary to arrive at the optimum setting.
20 Start the engine. open the throttle fully . Adjust the neede-valve. Close the throttle gradually. Find the idling position. Fix the idling position. Open the throttle fully. Does the engine regain full power? Continue running at high speed for 5 seconds.
21 + Adjusting the mixture control v alve If the engine hesitates, puffing out a good deal of smoke, before picking up to full speed, it is probable that the idling mixture is too rich.
23 VALVE CLEARANCE ADJUSTMENT Remove the rocker cover from each cylinder head by unscrewing two socket-head cap-screws from the rocker box on top of the cylinder head with Allen key supplied. ALL O.S. four-stroke engines have their valve (tappet) clearances correctly set before they leave the factory.
25 Remove 0.04mm feeler, rotate prop through two revolutions and recheck gap. 5. If clearance is correct, loosen the locknut on the other rocker-arm and repeat steps 1 to 5 above. Finally, replace rocker box cover. 6. Remember: Excessive valve clearance will cause loss of power, due to valve (s) not opening sufficiently.
26 EXPLODED VIEW Type of screw C...Cap Screw M...Oval Fillister-Head Screw F...Flat Head Screw N...Round Head Screw S...Set Screw M3 C.M2.6x7 C.M3.5x20 C.
28 26381501 24981405 26381501 46481320 22781800 46481330 26381501 46481200 46281340 46481310 22781800 46481100 46281900 29081952 24981837 26381501 46181940 46181941 46181950 26711305 26781619 26681305 26681803 45581700 1 2 2-1 3 3-1 4 4-1 5 6 7 7-1 8 9 9-1 9-2 9-3 9-4 9-5 9-6 9-7 10 10-1 10-2 11 Description Code No.
30 13.26cc x 2 / 1.218cu.in. x 2 27.7mm / 1.091in. 22.0mm / 0.866in. 2.000-10.000r.p.m. 1,100g / 38.8oz. 23.5 50.5 63.5 4 -5.2 56.5 196 54 68 120 76 THREE VIEW DRAWING Dimensions(mm) Specifications Displacement Bore Stroke PracticalR.P.M. Output Weight C Copyright 2004 by O.
デバイスGemini Industries FT-160の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gemini Industries FT-160をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGemini Industries FT-160の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gemini Industries FT-160の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gemini Industries FT-160で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gemini Industries FT-160を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGemini Industries FT-160の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gemini Industries FT-160に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGemini Industries FT-160デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
