General Tireメーカー15-220の使用説明書/サービス説明書
ページ先へ移動 of 18
Rotating & oscillating effect ensures exceptional finishing results. Precision ground cast iron table. On-board side mounted spindle storage. Tilting table for sanding be veled parts . 2” diameter dust outlet with 2” to 4” adapter fitting included.
THANK Y OU for choosing this General® International model 15-220 oscillating spindle sander . This machine has been carefully tested and inspected before shipment and if properly used and maintained, will pro vide y ou with years of reliable ser vice.
1. Do not operate this sander when tired, distracted or under the effects of drugs, alcohol or any medica- tion that impairs reflexes or aler tness. 2. Keep the w or k area well lit, clean and free of debris . 3. Stay aler t! Give y our work your undivided attention.
GR OUNDING INSTRUCTIONS In the ev ent of an electrical malfunction or shor t circuit, grounding reduces the risk of electric shock to. This motor of this machine is wired for 110V single phase operation and is equipped with a 3-conductor cord and a 3-prong gr ounded plug to f it a grounded type sock et.
VERTICAL OSCILLA TING SPINDLE SANDER 15-220 IDENTIFICA TION OF MAIN P ARTS AND COMPONENTS A CCESSORY STORA GE BASE C AST -IRON TABLE SWITCH ASSEMBL Y T ABLE INSERT T ABLE TIL T LOCK LEVER SANDING SPIN.
UNP ACKING AND SET -UP UNP ACKING Carefully unpack and remo ve the unit and its components from its shipping container and chec k for missing or damaged items as per the list of contents below . NOTE: Please report any damaged or missing items to y our GENERAL® INTERNA TIONAL distributor immediately .
ASSEMBL Y INSTRUCTIONS All unpainted surfaces are co vered with a protectiv e coating that prev ents rus t from f orming dur ing shipping and storage. Peel off the plastic co ver fr om the ta ble and remo ve this protectiv e coating b y rubbing with a rag dipped in k erosene, mineral spirits or paint thinner .
INST ALL THE SANDING SLEEVES ONTO THEIR CORRESPONDING SPINDLES Step 1 For 1/4, 1/2, & 5/8 spindles loosen the screw on the brack et clamp ( ) at the bottom of the spindle. Step 2 Slide the sanding sleev e onto the spindle completely . Note: the sleev e should slide under the brack et clamp as shown.
ACCESSORY STORAGE SPINDLES Place the drums into their s torage space on the right side of the machine. T ABLE INSERT PL A TES Store the table inser t plates in the storage slots on the left side of the machine. INST ALLING SPINDLES ON THE MACHINE If installed, remov e the table inser t to allow better access the spindle seat.
10 SELECTION GUIDE FOR T ABLE INSERTS This machine is supplied with 5 spindles, and four table inser ts. The spindle diameter s range from 1/4" to 2".
Step 3 If the table needs adjustment loosen both lock lev ers and readjust the table position until the square is flat against the table and the sanding drum. T o allo w for more or less rear tilt adjust the table stop rod as needed. Step 4 Mak e sure the pointer reads 0°.
• There is a 2” diameter dust outlet on the rear of the machine allowing f or the connection to a dust collector (not included). • A 2” TO 4” DUST HOSE AD APTOR is also included to f acilitate (if needed) connection to a standard 4” dust collection hose.
BASIC OPERA TIONS Before operating this machine, make sure y ou have read this manual attentiv ely! Failure to read and understand the instr uctions, w ar nings and safe- ty guidelines provided in this manual may lead to serious injur y and / or damage to machine or the workpiece.
RECOMMENDED OPTIONAL A CCESSORIES FOR Y OUR OSCILLA TING SPINDLE SANDER W e offer a large v ar iety of products to help y ou increase pro- ductivity , accuracy and safety when using your oscillating spin- dle sander . Here’s a small sampling of accessories av ailable from y our local General Inter national dealer .
15 Modèle #15-220.
16 P ARTS LIST 15-220 P AR T N0. REF . N0. DESCRIPTION SPECIFIC A TION QTY 15220-01 30201001G BASE 1 15220-02 30201001A TOP PLA TE 1 15220-03 S1006P1 STRAIN RELIEF 1 15220-04 L0000000 POWER CORD (W/PL.
17 P AR TS LIST 15-220 P AR T N0. REF . N0. DESCRIPTION SPECIFIC A TION QTY 15220-51 40501011A TABLE TIL T GUIDE BRA CKET (LEFT) 1 15220-52 30204013G LOCKING LEVER 2 15220-53 S0010516M PHILLIPS HEAD SCREW 4 15220-54 S0050606M SET SCREW M6 X 1.
IMPOR T ANT: When ordering replacement par ts, always giv e the model number , ser ial number of the machine and part number . Also a br ief descr iption of each item and quantity desired. 15-220 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 T el.
デバイスGeneral Tire 15-220の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
General Tire 15-220をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGeneral Tire 15-220の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。General Tire 15-220の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。General Tire 15-220で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
General Tire 15-220を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGeneral Tire 15-220の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、General Tire 15-220に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGeneral Tire 15-220デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
