GenieメーカーZ-80, Z-60の使用説明書/サービス説明書
ページ先へ移動 of 35
First Edition Third Printing Part No. 82258 Operator’ s Manual with Maintenance Information.
Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition • Third Printing Copyright © 2002 by Genie Industries First Edition: Third Printing, October 2002 "Genie" and "Z" are registered trademarks of Genie Industries in the U.
P ar t No . 82258 Genie Z-80/60 1 Operator's Manual First Edition · Third Printing Safety Rules Danger F ailure to obey the instructions and safety rules in this manual will result in death or serious injur y . Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual.
2 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing SAFETY RULES Electrocution Hazards This machine is not electrically insulated and will not provide protection from contact with or proximity to electrical current.
P ar t No . 82258 Genie Z-80/60 3 Operator's Manual First Edition · Third Printing If the tilt alarm sounds: Do not extend, rotate or raise the boom above horizontal.
4 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing Do not place or attach overhanging loads to any part of this machine. Do not place ladders or scaffolds in the platform or against any part of this machine. Do not use the machine on a moving or mobile surface or vehicle.
P ar t No . 82258 Genie Z-80/60 5 Operator's Manual First Edition · Third Printing SAFETY RULES Component Damage Hazards Do not use any battery or charger greater than 12V DC to jump-start the engine. Do not use the machine as a ground for welding.
6 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing SAFETY RULES Decal Legend Genie product decals use symbols, color coding and signal words to identify the following: Safety alert symbol—used to alert personnel to potential personal injury hazards.
P ar t No . 82258 Genie Z-80/60 7 Operator's Manual First Edition · Third Printing Controls Ground Control Panel 1 Boom down button 2 Boom extend/retract buttons 3 Boom up button 4 Engine speed .
8 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing CONTROLS 1 Machine on level surface symbol: High range operation for maximum drive speed 1 3 Steer mode select .
P ar t No . 82258 Genie Z-80/60 9 Operator's Manual First Edition · Third Printing CONTROLS 1 5 Used for optional equipment 1 6 Gasoline/LPG models: Gasoline/LPG select button with indicator lig.
10 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing Pre-operation Inspection Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations.
P ar t No . 82258 Genie Z-80/60 11 Operator's Manual First Edition · Third Printing PRE-OPERATION INSPECTION Pre-operation Inspection o Be sure that the operator’s, safety and responsibilities manuals are complete, legible and in the storage container located in the platform.
12 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing Maintenance Observe and Obey: Only routine maintenance items specified in this manual shall be performed by the operator.
P ar t No . 82258 Genie Z-80/60 13 Operator's Manual First Edition · Third Printing MAINTENANCE Deutz F4L 913 Engine Engine oil viscosity requirements below 60°F / 15.
14 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing MAINTENANCE Check the Batteries Proper battery condition is essential to good engine performance and operational safety. Improper fluid levels or damaged cables and connections can result in engine component damage and hazardous conditions.
P ar t No . 82258 Genie Z-80/60 15 Operator's Manual First Edition · Third Printing Function T ests Fundamentals The function tests are designed to discover any malfunctions before the machine is put into service. The operator must follow the step-by-step instructions to test all machine functions.
16 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing FUNCTION TESTS Test Auxiliary Controls 9 Shut the engine off. 1 0 Pull out the red Emergency Stop button to the on position. 1 1 Simultaneously push and hold the auxiliary power button and push each boom function button.
P ar t No . 82258 Genie Z-80/60 17 Operator's Manual First Edition · Third Printing FUNCTION TESTS At the Platform Controls Test Emergency Stop 2 2 Turn the key switch to platform control. 2 3 Push in the platform red Emergency Stop button to the off position.
18 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing FUNCTION TESTS Test the Steering (models with 4 wheel steer) 3 7 Push the steer mode select button for square- end (blue arrow) steer. 3 8 Press down the foot switch.
P ar t No . 82258 Genie Z-80/60 19 Operator's Manual First Edition · Third Printing Test Drive and Braking 5 2 Press down the foot switch. 5 3 Slowly move the drive/steer control handle in the direction indicated by the blue arrow on the control panel until the machine begins to move, then return the handle to the center position.
20 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing FUNCTION TESTS Test Limited Drive Speed 6 3 Press down the foot switch. 6 4 Raise the primary boom to 10° above horizontal. 6 5 Slowly move the drive control handle to the full drive position.
P ar t No . 82258 Genie Z-80/60 21 Operator's Manual First Edition · Third Printing W orkplace Inspection W orkplace Inspection Be aware of and avoid the following hazardous situations: · drop-.
22 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing Operating Instructions Starting the Engine 1 At the ground controls, turn the key switch to the desired position. 2 Be sure both the ground and platform control red Emergency Stop buttons are pulled out to the on position.
P ar t No . 82258 Genie Z-80/60 23 Operator's Manual First Edition · Third Printing OPERATING INSTRUCTIONS Operation from Platform 1 Turn the key switch to platform control. 2 Pull out both ground and platform red Emergency Stop buttons to the on position.
24 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing To Drive 1 Press down the foot switch. 2 Increase speed: Slowly move the drive/steer control handle in the direction indicated by the blue or yellow arrows. Decrease speed: Slowly move the drive/steer control handle toward center.
P ar t No . 82258 Genie Z-80/60 25 Operator's Manual First Edition · Third Printing OPERATING INSTRUCTIONS Check Engine Light Light on and engine stopped: Tag the machine and remove from service. Light on and engine still running: Contact service personnel within 24 hours.
26 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing Shading indicates decal is hidden from view, i.e. under covers Decals Part No.
P ar t No . 82258 Genie Z-80/60 27 Operator's Manual First Edition · Third Printing DECALS.
28 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing T ranspor t and Lifting Instructions Observe and Obey: The transport vehicle must be parked on a level surface. The transport vehicle must be secured to prevent rolling while the machine is being loaded.
P ar t No . 82258 Genie Z-80/60 29 Operator's Manual First Edition · Third Printing Securing to T ruck or T railer for T ransit Always use the turntable rotation lock pin each time the machine is transported. Turn the key switch to the off position and remove the key before transporting.
30 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing TRANSPORT AND LIFTING INSTRUCTIONS Observe and Obey: Only qualified riggers should rig and lift the machine. Be sure the crane capacity, loading surfaces and straps or lines are sufficient to withstand the machine weight.
P ar t No . 82258 Genie Z-80/60 31 Operator's Manual First Edition · Third Printing Specifications Z-80/60 Height, working maximum 86 ft 26.2 m Height, platform maximum 80 ft 24.4 m Height, stowed maximum 9 ft 10 in 3 m Horizontal reach maximum 60 ft 18.
32 Genie Z-80/60 P ar t No . 82258 Operator's Manual First Edition · Third Printing SPECIFICATIONS Z-80/60 Range of Motion 10 ft / 3 m 0 ft / 0 m 10 ft / 3 m 20 ft / 6.1 m 30 ft / 9.1 m 40 ft / 12.2 m 50 ft / 15.2 m 60 ft / 18.3 m 10 ft / 3 m 0 ft / 0 m 10 ft / 3 m 20 ft / 6.
Genie North America Genie Australia Pty Ltd. Genie China Genie Malaysia Genie Japan Genie Korea Genie Africa Genie Latin America Phone T oll Free Fax Phone + Fax + Phone + Fax + Phone + Fax + Phone + .
デバイスGenie Z-80, Z-60の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Genie Z-80, Z-60をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGenie Z-80, Z-60の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Genie Z-80, Z-60の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Genie Z-80, Z-60で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Genie Z-80, Z-60を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGenie Z-80, Z-60の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Genie Z-80, Z-60に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGenie Z-80, Z-60デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
