Gianni IndustriesメーカーAD-425Sの使用説明書/サービス説明書
ページ先へ移動 of 20
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 1/ 20 AD-425S Automatic Door Operator Instruction Manual General Safety Precautions z This instruction manual is intend ed sole ly for use by qualified professionals. All installation s, electrical connections and adjustments must follow the inst allation instructions.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 2/ 20 z Make sure the volt age specified as correct for the device. z Must provide at least 10 seconds rest ti me between every restarting cycle to ensure adequate residual current can be return ed to power system.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 3/ 20 All Packing materials 1. Construction Name ○ 1 C o v e r ○ 2 M o t o r ○ 3 Reducer ○ 4 Square Couplings ○ 5 Control Board ○ 6 Battery ○ 7 Power Switch ○ 8 Operating Arm ○ 9 Sliding Rail ○ 10 S topper Ball ○ 1 1 Baseplate ○ 12 T ransformer 2.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 4/ 20 3. Control Board Guide Input/Output Cont act Explanation Remark Make sure the input is use d corre ctly (AC1 10 or 220V). When turn on the power switch, it enters a learning mode.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 5/ 20 Input/Output Contact Explanation Remark Jumper 1-2 is N.C. cont act. N. C. (default) Jumper 1-3 is N.O. conta ct. N. O. (default) Jumper 1-8 is N.C., or using the “OPEN” switch.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 6/ 20 The opening, closing and maintain -open time illustration table. VM (Opening and Closing T im e Adjustment ) Opening.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 7/ 20 5. S pecification Power Input 1 10V (or 220V) AC ， 50-60H z Current (See Figure 2 ) 3.5A max., 0.6A average T orque 30Nm Opening/Closing time (VM) 4.5~9.5 s （ 90° ） Maintain - Op en time (TC) 1~35 seconds Battery S pecification 12V 1.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 8/ 20 Installation instructi ons z Refer to figure 3 for in-swing door (ri ght -hand).
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 9/ 20 Figure 5 : For right-hand and out-swing door . F/R switch set 「 ON 」 . Operating Arm mount s to left-side. Figure 6 : For left-hand and out-swing d oor . F/R switch set 「 1 」 .
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 10/ 20 z Figure 1 1~13 showing a n operator in stallation of a minimum door leaf wid th and a maximum opening angle. The opening angle is recommend ed not excess to 120 ∘ .
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2 008.07.1 1 Page: 1 1/ 20 AD-425S T emplate Installation Instruction Figure 17 Out-swing door (Right-Hand Open) Figure 18 Out-swing door (L.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 12/ 20 Inst allation Step s Out-swing door ( Right-Hand O pen ) S tep Figures Explanation S tep 1. Place the AD-425S template to the right position on the door header . See the figure presented for an out-swing door (Right-Hand Open), more det ails shown in Figure 17.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 13/ 20 S teps Figures Explanation S tep 7. Use Allen Wrench to tighten the Blind Nut. This will compress the sc rew so that it remains permanently fixed in the hole. Repeat these step s on other Blind Nuts.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 14/ 20 S teps Figures Explanation S tep 12. Use Allen Wrench to tighten the Blind Nut. This will compress the sc rew so that it remains permanently fixed in the hole. Repeat these step s on other Blind Nuts.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 15/ 20 S teps Figures Explanation S tep 18. T ighten screws. S tep 19. Insert screws (6 x 95 mm) to the Oper ating Arm on Square See the figure present e d for a out-swing door (Right-Hand Open), more det ails shown in Figure 9.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 16/ 20 S teps Figures Explanation S tep 24. Fix the Sliding Rail on the door leaf. (Screw specification: 6 X 20 mm) S tep 25. Slide in the Sliding Rail Cover . S tep 26. Attach two Side Ends.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 17/ 20 S teps Figures Explanation S tep 30. First opening movement, the AD-425S will b e automatically set the opening angle and dist ance. S tep 31. Attach the cover . S tep 32.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 18/ 20 T rouble shooting Problem Possible Cause Solution No AC power Make sure the Control Board an d fuse are working properly and connected properl y . Motor have no power (LED motor light not on.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 19/ 20 Problem Possible Cause Solution Safety devices are on Contact you r local distributor to check the Photocell and Safety Device. (ke ep the device clean) The door automatically open but doesn’t close.
Copyright All Rights Reserved. P-MU-AD425S V er . A Publish:2008.07.1 1 Page: 20/ 20 General Safety Precautions The following precautions are e ssential for the user . z Read the precaution below carefully as it cont ains imp ortant information about safe inst allation and maintenance.
デバイスGianni Industries AD-425Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Gianni Industries AD-425Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGianni Industries AD-425Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gianni Industries AD-425Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gianni Industries AD-425Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gianni Industries AD-425Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGianni Industries AD-425Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gianni Industries AD-425Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGianni Industries AD-425Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
