GigabyteメーカーGA-F2A78M-D3H (rev. 3.0)の使用説明書/サービス説明書
ページ先へ移動 of 96
GA-F2A78M-D3H User's Manual Rev . 30 01 1 2ME -F27 8M3H-3001 R.
Motherboard GA-F2A78M-D3H Dec. 12, 2013 Dec. 12, 2013 Motherboard GA-F2A78M-D3H.
Copyright © 2013 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE.
- 4 - T able of Contents Box C ontent s ................................................................................................................... 6 Optional Items ..............................................................................
- 5 - Chapter 4 Dri vers Installation ....................................................................................... 69 4 - 1 Inst alling Chipset Dr ivers ............................................................................... 69 4-2 A pplication Soft ware .
- 6 - Bo x Content s 5 GA-F2A78M-D3H motherboard 5 Motherboard driver disk 5 User's Manual 5 Quick Installation Guide 5 Four SA T A cables 5 I/O Shield Optional I tems 2-portUSB2.0bracket(PartNo.12CR1-1UB030-6*R) eSA T A bracket(PartNo.
- 7 - GA-F2A7 8M -D3H Motherboard La yo ut KB_MS_USB CPU_F AN SYS_F AN1 Socket FM2+ AT X F_USB30 AUDIO DDR3_4 DDR3_2 DDR3_3 DDR3_1 B AT A TX_12V AMD A78 CODEC CLR_CMOS M_BIOS B_BIOS DVI_VGA USB_LAN Re.
- 8 - GA- F 2 A 78M- D3H Mother board B lock Diagram Fordetailedproductinformation/limitation(s),referto"1-2ProductSpecications.
- 9 - Hardware Installation 1-1 Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damagedas aresultof electrostaticdischarge (ESD).
- 10 - Hardware Installation 1-2 ProductSpecications APU FM2+ Socket: - AMD A series processors - AMD Athlon ™ series processors (GotoGIGABYTE'swebsiteforthelatestCPUsupportlist.) Chipset AMD A78 Memory 4 x 1.
- 1 1 - Hardware Installation Storage Interface Chipset: - 6 x SA TA 6Gb/s connectors - Support for RAID 0, RAID 1, RAID 10, and JBOD USB Chipset: - 4 xUSB3.0/2.0ports(2ports onthebackpanel,2 portsavailablethrough theinternalUSBheader) - 8 xUSB2.
- 12 - Hardware Installation Unique Features Support for @BIOS Support for Q-Flash SupportforXpressInstall Support for EasyTune * AvailablefunctionsinEasyTunemaydif ferbymotherboardmodel.
- 13 - Hardware Installation 1-3 Installing the APU and APU Cooler 1-3-1 Installing the APU A. Locatethepinone(denotedbyasmalltriangle)ofthe APUsocketandthe APU. Read the following guidelines before you begin to install the APU: • Make sure that the motherboard supports the APU.
- 14 - Hardware Installation B. Follow the steps below to correctly install the APU into the motherboard APU socket. • Before installing the APU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the APU.
- 15 - Hardware Installation 1-3-2 Installing the APU Cooler Follow the steps below to correctly install the APU cooler on the motherboard. Use extreme care when removing the APU cooler because the thermal grease/tape between the APU cooler and APU may adhere to the APU.
- 16 - Hardware Installation 1-4 Installing the Memory Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory . It is recommended that memory of the same capacity , brand, speed, and chips be used.
- 17 - Hardware Installation 1-4-2 Installing a Memory Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs.
- 18 - Hardware Installation 1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: • Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
- 19 - Hardware Installation 1-6 Setupofthe AMDDualGraphicsConguration (Note) Make sure the drivers for the Chipset, onboard graphics, and external graphics card are properly installed.
- 20 - Hardware Installation 1-7 Back Panel Connectors USB 2.0/1.1 Port The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB keyboard/mouse,USBprinter ,USBashdriveandetc.
- 21 - Hardware Installation Optical S/PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital optical audio. Before using this feature, ensure that your audio system provides an optical digital audio in connector .
- 22 - Hardware Installation 1-8 Internal Connectors Read the following guidelines before connecting external devices: • First make sure your devices are compliant with the connectors you wish to connect. • Before installing the devices, be sure to turn off the devices and your computer .
- 23 - Hardware Installation 1/2) A TX_12V/A TX (2x4 12V Power Connector and 2x12 Main Power Connector) With the use of the power connector , the power supply can supply enough stable power to all the components onthe motherboard.
- 24 - Hardware Installation • Be sure to connect fan cables to the fan headers to prevent your APU and system from overheating. Overheating may result in damage to the APU or the system may hang. • These fan headersare not conguration jumper blocks.
- 25 - Hardware Installation 6) SA T A3 0/1/2/3/4/5 (SA T A 6Gb/s Connectors) The SA T A connectors conform to SA T A 6Gb/s standard and are compatible with SA T A 3Gb/s and SA T A 1.5Gb/s standard. Each SA T A connector supports a single SA T A device.
- 26 - Hardware Installation The front panel design may differ by chassis. A front panel module mainly consists of power switch, resetswitch,powerLED, harddriveactivityLED,speakerandetc.
- 27 - Hardware Installation 9) F_AUDIO (Front Panel Audio Header) The frontpanel audio headersupports IntelHigh Denitionaudio (HD)and AC'97audio. Y oumay connect your chassis front panel audio module to this header .
- 28 - Hardware Installation 12) F_USB1/F_USB2 (USB 2.0/1.1 Headers) Theheadersconform toUSB 2.0/1.1 specication.Each USBheader canprovide twoUSB portsvia an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer .
- 29 - Hardware Installation 13) COM (Serial Port Header) The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer .
- 30 - Hardware Installation 20 19 2 1 F_USB30 F_U B_ F_ F_ _ .
- 31 - BIOS Setup BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard.
BIOS Setup - 32 - 2-1 Startup Screen The following startup Logo screen will appear when the computer boots. FunctionKeys: <DEL>:BIOSSETUPQ-FLASH Pressthe<Delete>keytoenterBIOSSetuportoaccesstheQ-FlashutilityinBIOSSetup.
- 33 - BIOS Setup 2-2 The Main Menu Onthemain menuoftheBIOS Setupprogram,pressarrow keystomoveamong theitemsandpress<Enter> to accept or enter a sub-menu. Or you can use your mouse to select the item you want.
BIOS Setup - 34 - BIOS Setup Menus M.I.T . Use thismenu tocongure theclock, frequency , andvoltagesof yourCPU and memory ,etc. Orcheck the system/CPU temperatures, voltages, and fan speeds.
- 35 - BIOS Setup 2-3 M.I.T . Whetherthesystemwill workstablywiththeoverclock/overvoltage settingsyoumadeis dependent onyouroverallsystem congurations.
BIOS Setup - 36 - ` M.I.T . Current Status This screen provides information on CPU/memory frequencies/parameters. ` Advanced Frequency Settings & CPU Clock Control AllowsyoutomanuallysettheCPUbaseclockin1MHzincrements.
- 37 - BIOS Setup (Note) ThisitemispresentonlywhenyouinstallaCPUthatsupportsthisfeature. & CPU Clock Ratio, CPU Frequency The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu.
BIOS Setup - 38 - & CPU Core Control Allows you to determine whether to manually enable/disable CPU cores. Automatic mode allows the BIOS toenable allCPUcores (numberof coresavailabledepends ontheCPU beingused).
- 39 - BIOS Setup ` Advanced Memory Settings & ExtremeMemoryProle(X.M.P .) (Note) , System Memory Multiplier , Memory Frequency(MHz) The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu.
BIOS Setup - 40 - This sub-menu provides memory timing settings for each channel of memory . This sub-menu provides memory timingsettingsforeachchannel ofmemory .Therespectivetiming settingscreensarecongurableonlywhen Memory Timing Mode is set to Manual or Advanced Manual .
- 41 - BIOS Setup ` PC Health Status & Reset Case Open Status Disabled Keepsorclearstherecordofpreviouschassisintrusionstatus.(Default) Enabled Clears the record of previous chassis intrusion status and the Case Open eldwill show "No"atnextboot.
BIOS Setup - 42 - & CPU Vcore/DRAM V oltage/+3.3V/+5V/+12V Displays the current system voltages. & CPU/System T emperature Displays current CPU/system temperature. & CPU/System Fan Speed Displays current CPU/system fan speeds. & CPU T emperature Warning Sets thewarning thresholdfor CPUtemperature.
- 43 - BIOS Setup 2-4 System Information This section provides information on your motherboard model and BIOS version. Y ou can also select the default language used by the BIOS and manually set the system time. & System Language Selects the default language used by the BIOS.
BIOS Setup - 44 - 2-5 BIOS Features & Boot Option Priorities Speciesthe overall boot order from the available devices. For example, you can set hard drive as the rstpriority( Boot Option #1 )andDVDROMdriveasthesecond priority( Boot Option #2 ).
- 45 - BIOS Setup & Hard Drive/CD/DVD ROM Drive/Floppy Drive/Network Device BBS Priorities Speciesthebootorder foraspecicdevice type,suchas harddrives,optical drives,oppydiskdrives, and devices that support Boot from LAN function, etc.
BIOS Setup - 46 - & CSM Support EnablesordisablesUEFICSM(CompatibilitySupportModule)tosupportalegacyPCbootprocess. Always EnablesUEFICSM.(Default) Never DisablesUEFICSMandsupportsUEFIBIOSbootprocessonly .
- 47 - BIOS Setup & User Password Allowsyoutocongure auserpassword.Press<Enter>onthis item,typethepassword,andthenpress <Enter>. Y ou will be requested to conrm the password.
BIOS Setup - 48 - 2-6 Peripherals & IOMMU Enablesordisables AMDIOMMUsupport.(Default:Disabled) & OnChip USB Controller EnablesordisablestheintegratedUSBcontroller .(Default:Enabled) & HD Audio Azalia Device Enablesordisablestheonboardaudiofunction.
- 49 - BIOS Setup & Onboard LAN Controller EnablesordisablestheonboardLANfunction.(Default:Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled .
BIOS Setup - 50 - ` SA T A Conguration & OnChip SA T A Channel EnablesordisablestheintegratedSA T A controllers.(Default:Enabled) & OnChip SA T A T ype En.
- 51 - BIOS Setup & Parallel Port Enablesordisablestheonboardparallelport(LPT).(Default:Enabled) & Device Mode This itemis congurable onlywhen Parallel Port is set to Enabled . It allows you to select an operating modefortheonboardparallel (LPT)port.
BIOS Setup - 52 - 2-7 Power Management (Note) SupportedonWindows8/7operatingsystemonly . & Resume by Alarm Determineswhethertopoweronthesystematadesiredtime.
- 53 - BIOS Setup & Power On By Keyboard Allows the system to be turned on by a PS/2 keyboard wake-up event. Note:T ousethisfunction,youneedan A TXpowersupplyprovidingatleast1A onthe+5VSBlead.
BIOS Setup - 54 - 2-8 Save & Exit & Save & Exit Setup Press <Enter>on thisitem andselect Ye s . This saves the changes to the CMOS and exits the BIOS Setup program. Select No orpress<Esc>toreturntotheBIOSSetupMainMenu.
- 55 - Conguring SA T A Hard Drive(s) Chapter3 ConguringSA T A HardDrive(s) (Note1) SkipthisstepifyoudonotwanttocreateRAIDarrayontheSA T Acontroller . (Note2) RequiredwhentheSA T Acontrollerissetto AHCIorRAIDmode.
ConguringSA T AHardDrive(s) - 56 - Step 2: Ifyou wantto congureUEFI RAID,follow thestepsin "C-1." T oenter thelegacyRAID ROM,save thesettings and exit BIOS Setup. Refer to "C-2" for more information.
- 57 - Conguring SA T A Hard Drive(s) C-1.UEFIRAIDConguration ThismodesupportsWindows864-bitinstallationonly . T o congure UEFI RAID, you need .
ConguringSA T AHardDrive(s) - 58 - Figure 5 Creating a RAID Array T o create a RAID array , refer to the following examples to enter the commands and press <Enter>. When succeeded, the message which says "created sucessfully" will appear .
- 59 - Conguring SA T A Hard Drive(s) T oexittheUEFIRAIDutility ,enter"exit"andpress<Enter>. Deleting an Array T odeleteanarray ,enterthefollowingcommandsandpress<Enter>.
ConguringSA T AHardDrive(s) - 60 - C-2.ConguringLegacyRAIDROM Enter the legacy RAIDBIOS setup utility to congure a RAID array .Skip this step and proceed with the installation ofWindowsoperatingsystemforanon-RAIDconguration.
- 61 - Conguring SA T A Hard Drive(s) First, select a RAIDmode and press<Enter>. The selections available dependon the numberof thehard drives being installed. Then follow the on-screen instructions to specifythe array size.
ConguringSA T AHardDrive(s) - 62 - Figure 12 AMD-RAID Array Conguration (Build: 6.1.1-00075) Arrays Create Array < h >< i >< f >< g >=Choose, <Esc>=Back &l.
- 63 - Conguring SA T A Hard Drive(s) Deleting an Array The Delete Array(s) menu option allows for deletion of disk array assignments. 1. Select Delete Array(s) in the Main Menu andpress<Enter>.
ConguringSA T AHardDrive(s) - 64 - 3-2 Installing the SA T A RAID/AHCI Driver and Operating System WiththecorrectBIOSsettings,youarereadytoinstalltheoperatingsystem. A. Installing Windows 8/7 (ThefollowinginstructionsuseWindows8astheexampleoperatingsystem.
- 65 - Conguring SA T A Hard Drive(s) Figure 2 B. Installing Windows XP (32-bit) Before installing WindowsXP , connect aUSB oppy disk drive to yourcomputer.
ConguringSA T AHardDrive(s) - 66 - Figure 3 RefertothefollowingforinstallingthedriverduringtheWindowssetupprocess.
- 67 - Conguring SA T A Hard Drive(s) RebuildinganArray: Rebuilding is the process of restoring data to a hard drive from other drives in the array . Rebuilding applies only to fault-tolerant arrays such as RAID 1 and RAID 10 arrays. T o replace the old drive, make sure to use a new drive of equal or greater capacity .
ConguringSA T AHardDrive(s) - 68 -.
- 69 - Drivers Installation 4-1 Installing Chipset Drivers Chapter 4 Drivers Installation • Before installing the drivers, rst install the operating system. (The following instructions use Windows8astheexampleoperatingsystem.
Drivers Installation - 70 - 4-2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software. Y ou can click the Install button on the right of an item to install it. 4-3 T echnical Manuals This page provides the content descriptions for this driver disk.
- 71 - Drivers Installation 4-4 Contact For thedetailed contact informationof the GIGABYTET aiwan headquarter orworldwide branch ofces,click the URL on this page to link to the GIGABYTE website. 4-5 System This page provides the basic system information.
Drivers Installation - 72 - 4-6 Download Center T o update the BIOS, drivers, or applications, click the Download Center button to link to the GIGABYTE website.
- 73 - Unique Features 5-1 BIOS Update Utilities GIGABYTE motherboards provide two unique BIOS update tools, Q-Flash ™ and @BIOS ™ . GIGABYTE Q-Flash and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MS-DOS mode.
Unique Features - 74 - B. Updating the BIOS In the main menu of Q-Flash, use the keyboard or mouse to select an item to execute. When updating the BIOS,choose the locationwhere theBIOS leis saved.
- 75 - Unique Features Step 4: DuringthePOST , press<Delete>toenterBIOSSetup. Select Load Optimized Defaults on the Save & Exit screen and press <Enter> to load BIOSdefaults.
Unique Features - 76 - 5-1-2 Updating the BIOS with the @BIOS Utility A. Before Y ou Begin 1. In Windows,closeallapplicationsandTSR(T erminateand StayResident)programs.Thishelpsprevent unexpected failures when performing a BIOS update.
- 77 - Unique Features 5-2 EasyT une 6 GIGABYTE's EasyTune 6 is a simple and easy-to-use interface that allows users to ne-tune their system settings or do overclock/overvoltage in Windows environment.
Unique Features - 78 - 5-3 Smart Recovery 2 SmartRecovery2 allowsyoutoback upapartitionasan imageleeveryhour.Y oucanusethese imagesto restoreyoursystemorleswhenneeded.
- 79 - Unique Features Recovering your system with Smart Recovery 2 (Windows 8/7 only): Steps: 1. Click the File Recovery button on the main menu. 2. Select the location where your backup is saved. 3. Use the time slider to select a time point.
Unique Features - 80 -.
Appendix - 81 - 6-1 Conguring AudioInputandOutput Chapter 6 Appendix HighDenitionAudio(HD Audio) HD Audioincludesmultiple highqualitydigital-to-analogconverters (DACs).
Appendix - 82 - The pictures to the right show the 7.1-channel speaker congurations. 7.1-Channel Speakers: Center/Subwoofer Speaker Out Front Speaker Out Rear Speaker Out Side Speaker Out Step 2: Connect an audio device to an audio jack. The The current connected device is dialog box appears.
Appendix - 83 - If your chassis provides an AC'97 front panel audio module, to activate the AC'97 functionality , click the tool icon on the Speaker Conguration tab. On the Connector Settings dialog box, select the Disable front panel jack detection check box.
Appendix - 84 - 6-1-2 ConguringS/PDIFOut The S/PDIF Out jack can transmit audio signals to an external decoder for decoding to get the best audio quality .
Appendix - 85 - 6-1-3 ConguringMicrophoneRecording Step 2: Connectyour microphoneto theMic injack (pink)on the back panel or the Mic in jack (pink) on the front panel. Thencongurethejackformicrophonefunctionality .
Appendix - 86 - Step 5: T o open the Sounder Recorder , move the mouse cursor to the bottom left corner of the screen, click the Start icon to switch to the Start screen (orpressthe Windows button on the keyboard).
Appendix - 87 - 6-1-4 Using the Sound Recorder A. Recording Sound 1. Makesureyouhaveconnectedthesoundinputdevice(e.g.microphone)tothecomputer . 2. T o record the audio, click the Start Recording button . 3. T o stop recording audio, click the Stop Recording button .
Appendix - 88 - 6-2 T roubleshooting 6-2-1 Frequently AskedQuestions T o read more F AQs for your motherboard, please go to the Support& DownloadsF AQ page on GIGABYTE's website.
Appendix - 89 - 6-2-2 T roubleshooting Procedure If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the problem. ST ART A Turn of f the power. Remove all peripherals, connecting cables, and power cord etc.
Appendix - 90 - If the procedure above is unable to solve your problem, contact the place of purchase or local dealer for help. Or go to the Support & DownloadsT echnical Support page to submit your question. Our customer service staff will reply you as soon as possible.
Appendix - 91 - Regulatory Statements Regulatory Notices This document must not be copied without our written permission, and the contents there of must not be imparted to a thirdparty norbe usedfor anyunauthorized purpose.
Appendix - 92 - FCC Notice (U.S.A. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix - 93 -.
Appendix - 94 -.
Appendix - 95 - Contact Us • GIGA-BYTE TECHNOLOGY CO., L TD. Address:No.6,BaoChiangRoad,Hsin-TienDist., NewT aipeiCity231,T aiwan TEL: +886-2-8912-4000 F AX:+886-2-8912-4005 T ech.andNon-T ech.Support(Sales/Marketing): http://ggts.
Appendix - 96 - • GIGABYTE Global Service System T osubmit a technicalor non-technical(Sales/Marketing) question, please link to: http://ggts.gigabyte.com.tw Then select your language to enter the system. • G.B.T . TECHNOLOGY TRADING GMBH - Germany WEBaddress:http://www .
デバイスGigabyte GA-F2A78M-D3H (rev. 3.0)の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Gigabyte GA-F2A78M-D3H (rev. 3.0)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGigabyte GA-F2A78M-D3H (rev. 3.0)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Gigabyte GA-F2A78M-D3H (rev. 3.0)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Gigabyte GA-F2A78M-D3H (rev. 3.0)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Gigabyte GA-F2A78M-D3H (rev. 3.0)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGigabyte GA-F2A78M-D3H (rev. 3.0)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Gigabyte GA-F2A78M-D3H (rev. 3.0)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGigabyte GA-F2A78M-D3H (rev. 3.0)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。