AmanaメーカーW10296137A-SPの使用説明書/サービス説明書
ページ先へ移動 of 16
1 W10300459A W10296137A-SP DR YER SAFETY ......................................................................... 2 INST ALLA TION REQUIREMENTS ............................................. 3 T ools and Parts .........................................
2 DR YER SAFETY You You can be killed or seriously injured if you don't immediately can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
3 INST ALLA TION REQUIREMENTS T ools and Parts Gather the requir ed tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
4 Installation clearances: The location must be lar ge enough to allow the dryer door to open fully . Dryer Dimensions A B D C 43 3 / 8 " (1102 mm) *26" (660 mm) 29" (737 mm) 15 1 / 4 &.
5 Install Leveling Legs W ARNING Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury. 1. T o avoid damaging the oor , use a large at piece of cardboar d from the dryer carton.
6 Electrical Connection Power Supply Cord W ARNING Fire Hazar d Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wir e) to center terminal (silver).
7 3. Install strain relief. Style 1: Power supply cord strain r elief Remove the screws fr om a 3/4" (19 mm) UL listed strain relief ■ (UL marking on strain relief).
8 3. Connect neutral ground wir e (E) and the neutral wire (C) (white or center wire) of power supply cor d under center , silver -color ed terminal block screw (B). Tighten scr ew . B C E 4. Connect ground wire (F) (gr een or bare) of power supply cor d to external ground conductor screw (A).
9 4. Tighten strain relief scr ews. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down scr ew . 6. Y ou have completed your electrical connection.
10 3-wire connection: Dir ect wire Use where local codes permit connecting cabinet-gr ound conductor to neutral wire. Direct wir e cable must have 5 ft. (1.52 m) of extra length so dryer can be moved if needed. Strip 3½" (89 mm) of outer covering from end of cable.
11 4. Connect the other wires to outer terminal block scr ews. Tighten screws. 5. Tighten strain relief scr ews. 6. Insert tab of terminal block cover into slot of dryer rear panel.
12 Clamps: Use clamps to seal all joints. ■ Exhaust vent must not be connected or secured with scr ews ■ or other fastening devices that extend into interior of vent and catch lint. Do not use duct tape. Clamp Exhaust: Recommended hood styles. Acceptable hood style.
13 Level Dryer Check the levelness of the dryer . Check levelness rst side to side, then front to back. If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness. NOTE: It might be necessary to level the dryer again after it is moved into its nal position.
14 11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door . If you do not feel heat, turn off dryer , and check the following: There may be 2 household fuses or cir cuit breakers for ■ the dryer .
15 6. Be certain to keep car dboard spacer center ed between doors. Reattach outer door panel to inner door panel so handle is on the side where hinges wer e just removed. 7. Attach door hinges to dryer door so that the lar ger hole is at the bottom of the hinge.
16 W10300459A W10296137A-SP © 2009 12/09 All rights reserved Printed in U.S.A..
デバイスAmana W10296137A-SPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Amana W10296137A-SPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAmana W10296137A-SPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Amana W10296137A-SPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Amana W10296137A-SPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Amana W10296137A-SPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAmana W10296137A-SPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Amana W10296137A-SPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAmana W10296137A-SPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
