GMCメーカーAcadia 15919282の使用説明書/サービス説明書
ページ先へ移動 of 516
Seats and Restraint System ............................... 1 - 1 Head Restraints .............. 1 - 2 Front Seats .................... 1 - 3 Rear Seats ................... 1-10 Safety Belts .................. 1-15 Child Restraints ............. 1-30 Airbag System .
GENERAL MOTORS, GM, the GM Emblem, GMC, the GMC Emblem, and the name ACADIA, are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. GM reserves the right to make changes after that time without further notice.
Index To quickly locate information about the vehicle, use the index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this” or “Do not let this happen.
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index.
Seats and Restraint System Head Restraints Head Restraints ................... .1-2 Front Seats Manual Seats ...................... .1-3 Seat Height Adjuster ............. .1-3 Power Seats ........................ .1-4 Manual Lumbar ..................
Head Restraints The vehicle’s front seats have adjustable head restraints in all outboard seating positions. { CAUTION With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suf fer a neck/spinal injury in a crash.
Front Seats Manual Seats { CAUTION You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Power Seats A. Power Seat Adjustment Control B. Reclining Seatbacks on page 1-8 . C. Power Lumbar on page 1-5 . If the vehicle has power seats, the controls are located on the outboard side of the seats. Move the seat forward or rearward by sliding the power seat adjustment control (A) forward or rearward.
Power Lumbar If the seats have power lumbar, the controls used to operate this feature are located on the outboard side of the seats. See “Power Lumbar” under Power Seats on page 1-4 for more information. To increase or decrease lumbar support, press and hold the front or rear of the control (C).
Heated and Cooled Seats If the front seats have the heated and cooled seat feature, the buttons used to control this feature are located on the front doors near the door handle. H (Cooled Seat): To cool the entire seat, press the button with the cooled seat symbol.
To save positions in memory: 1. Adjust the driver seat, including the seatback recliner and both outside mirrors to a comfortable position. See Outside Power Mirrors on page 2-32 for more information. Not all mirrors will have the ability to save and recall the mirror positions.
Further programming for the memory seat feature can be done using the DIC. You can select or cancel the following: • The automatic easy exit seat feature. • The remote memory seat recall feature. For programming information, see DIC Vehicle Customization (With DIC Buttons) on page 3-67 .
Power Reclining Seatbacks In vehicles with seats that have power reclining seatbacks, the control used to recline them is located on the outboard side of the seat behind the power seat control. See Power Seats on page 1-4 for more information. • To recline the seatback, tilt the top of the control rearward.
Rear Seats Rear Seat Operation A. Seat Adjustment Handle B. Reclining Seatback Strap C. Sliding Seat Lever Entering and Exiting the Third Row { CAUTION Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash.
3. Place folding armrests in the upright position. 4. Ensure that the safety belt is unfastened and in the stowed position. 5. Pull the sliding seat lever (C) forward and move the seatback forward. The seat cushion will fold, and the entire seat will slide forward.
Adjusting the Seats To adjust the second row seats, pull outward on the seat adjustment handle (A). Slide the seat forward or rearward to the desired position.
3. Pull up on the release lever located on the back of the seat. The headrest moves forward automatically. 4. Push the seatback forward to lay flat. To return the seatback to the seating position: 1. Raise the seatback into place by using the pullstrap from the rear of the vehicle, or by pushing it into place from inside the vehicle.
Removing the Third Row Seats 1. Remove the cargo management system, if it is in the vehicle. See Cargo Management System on page 2-52 . 2. Remove anything on or under the seat. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. { CAUTION Do not let anyone ride where a safety belt cannot be worn properly.
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Take the simplest vehicle. Suppose it is just a seat on wheels. Put someone on it.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are dif ferent rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 1-30 or Infants and Young Children on page 1-32 .
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way. { CAUTION You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
{ CAUTION You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs.
Q: What is wrong with this? A: The belt is over an armrest. { CAUTION You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
{ CAUTION You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it.
3. Push the latch plate into the buckle until it clicks. 4. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-29 . Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling of f of the shoulder.
Pretensioners work only once. If the pretensioners activate in a crash, they will need to be replaced, and probably other new parts for the vehicle’s safety belt system.
2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. { CAUTION A safety belt that is not properly worn may not provide the protection needed in a crash.
4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide.
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster.
In a crash, children who are not buckled up can strike other people who are buckled up, or can be thrown out of the vehicle. Older children need to use safety belts properly. { CAUTION Never do this. Never allow two children to wear the same safety belt.
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
{ CAUTION Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the dif ferent types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types.
Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child’s body with the harness.
Securing an Add-On Child Restraint in the Vehicle { CAUTION A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts.
Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
i (Top Tether Anchor): Seating positions with top tether anchors. j (Lower Anchor): Seating positions with two lower anchors. i (Top Tether Anchor): Seating positions with top tether anchors. To assist you in locating the lower anchors, each second row anchor position has a label, near the crease between the seatback and the seat cushion.
The top tether anchors are located at the bottom rear of the seatback for each seating position in the second row. Open the cover to access the anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
Securing a Child Restraint Designed for the LATCH System { CAUTION If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed.
1.2. Recline the seatback to the full reclined position. Make sure the second row bench seatbacks are aligned at the same angle before placing the child restraint on the seat. Make sure the third row bench seatbacks are both upright before placing the child restraint on the seat.
If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. If the position you are using has a fixed headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint.
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle.
4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Securing a Child Restraint in the Right Front Seat Position The vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint.
Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impact airbag for the right front passenger.
{ CAUTION Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger side. The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
The roof-rail airbags for the driver, right front passenger, passengers behind the driver and right front passenger, and the third row outboard passengers are in the ceiling above the side windows.
Frontal airbags may inflate at dif ferent crash speeds. For example: • If the vehicle hits a stationary object, the airbags could inflate at a dif ferent crash speed than if the vehicle hits a moving object.
In any particular crash, no one can say whether an airbag should have inflated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, inflation is determined by what the vehicle hits, the angle of the impact, and how quickly the vehicle slows down.
Rollover capable roof-rail airbags are designed to help contain the head and chest of occupants in the outboard seating positions in the first, second, and third rows. The rollover capable roof-rail airbags are designed to help reduce the risk of full or partial ejection in rollover events, although no system can prevent all such ejections.
In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system.
We recommend that children be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts.
When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active.
If the Of f Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the of f indicator is lit, it could be because that person is not sitting properly in the seat.
A wet seat can af fect the performance of the passenger sensing system. Here is how: • The passenger sensing system may turn of f the passenger airbag when liquid is soaked into the seat. If this happens, the of f indicator will be lit, and the airbag readiness light on the instrument panel will also be lit.
Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Q: Because I have a disability, I have to get my vehicle modified. How can I find out whether this will af fect my airbag system? A: If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual.
Replacing Restraint System Parts After a Crash { CAUTION A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash.
Features and Controls Keys Keys .................................. .2-2 Remote Keyless Entry (RKE) System ............................. .2-3 Remote Keyless Entry (RKE) System Operation ............... .2-4 Remote Vehicle Start ............ .2-6 Doors and Locks Door Locks .
Storage Areas Glove Box ......................... .2-49 Cupholders ........................ .2-49 Instrument Panel Storage ..... .2-49 Center Console Storage ...... .2-50 Second Row Center Console ........................... .2-50 Floor Mats .........
See your dealer/retailer if a replacement key or additional key is needed. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. If you are locked out of the vehicle, call the Roadside Assistance Center.
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can af fect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-3 .
Press and hold L for more than two seconds to activate the panic alarm. The parking lamps flash and the horn sounds repeatedly for 30 seconds. The alarm turns of f when the ignition is moved to ON/RUN or L is pressed again. The ignition must be in LOCK/OFF for the panic alarm to work.
Remote Vehicle Start This vehicle may have a remote starting feature that starts the engine from outside of the vehicle. If the vehicle has an automatic climate control system, the climate control system defaults to a heating or cooling mode depending on the outside temperatures.
After entering the vehicle during a remote start, insert and turn the key to the ON/RUN position to drive the vehicle. If the vehicle is left running it automatically shuts of f after 10 minutes unless a time extension has been done.
Doors and Locks Door Locks { CAUTION Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
This feature will not operate if the key is in the ignition. This feature can be programmed by using the Driver Information Center (DIC). See “DELAY DOOR LOCK” under DIC Vehicle Customization (With DIC Buttons) on page 3-67 .
Liftgate { CAUTION Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Power Liftgate Power Liftgate Operation { CAUTION Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
The power liftgate can be power opened and closed in the following ways: • Press and hold the power liftgate button on the RKE transmitter until the liftgate starts moving. Remote Keyless Entry (RKE) System Operation on page 2-4 for more information.
After removing the obstruction, the power liftgate operation can be used again. If the liftgate comes across more obstacles on the same power cycle, the power function deactivates, and you must manually open or close the liftgate. A message displays, LIFTGATE OPEN, to indicate that the liftgate is open.
Windows { CAUTION Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suf fer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Press the switch to lower the window. Pull up on the front edge of the switch to raise the window. Express-Down Windows The express-down feature allows the windows to be lowered without holding the switch. Press the window switch fully and release it to activate the express-down feature.
Sun Visors Pull the sun visor down to block glare. Detach the sun visor from the center mount and slide it along the rod from side-to-side to cover the driver or passenger side of the front window. Swing the sun visor to the side to cover the side window.
The horn chirps and the lights flash. If the key is not placed in the ignition and turned to START or the door is not unlocked by pressing Q during the ten second pre-alarm, the alarm goes of f. The headlamps flash and the horn sounds for about two minutes, then turns of f to save the battery power.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
If the vehicle does start, the first key may be faulty. See your dealer/retailer who can service the PASS-Key ® III+ to have a new key made. In an emergency, contact Roadside Assistance. See Roadside Assistance Program on page 7-6 . It is possible for the PASS-Key ® III+ decoder to learn the transponder value of a new or replacement key.
Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • If you have all-wheel drive, keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km).
way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer. ( (LOCK/OFF): This position locks the ignition and transmission. The key can be removed in LOCK/OFF. The shift lever must be in P (Park) to turn the ignition switch to LOCK/OFF.
Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. To restart the engine when the vehicle is already moving, use N (Neutral) only. Notice: Do not try to shift to P (Park) if the vehicle is moving.
accelerator. If the vehicle starts briefly but then stops again, repeat these steps. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts.
Automatic Transmission Operation The automatic transmission has a shift lever located on the console between the seats. P (Park): This position locks the front wheels. It is the best position to use when starting the engine because the vehicle cannot move easily.
N (Neutral): In this position, the engine does not connect with the wheels. To restart the engine when the vehicle is already moving, use N (Neutral) only. Also, use N (Neutral) when the vehicle is being towed. { CAUTION Shifting into a drive gear while the engine is running at high speed is dangerous.
When you shift from D (Drive) to L (Low), the transmission will shift to a pre-determined lower gear range. The highest gear available for this pre-determined range is displayed next to the L in the DIC.
Automatic Engine Grade Braking Automatic Engine Grade Braking assists when driving on a downhill grade. It maintains vehicle speed by automatically implementing a shift schedule that uses the engine and the transmission to slow the vehicle.
Shifting Into Park { CAUTION It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
To prevent torque lock, set the parking brake and then shift into P (Park). To find out how, see “Shifting Into Park” listed previously. If torque lock does occur, your vehicle may need to be pushed uphill by another vehicle to relieve the parking pawl pressure, so you can shift out of P (Park).
Engine Exhaust { CAUTION Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).
{ CAUTION It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to.
Automatic Dimming Mirror Operation Automatic dimming reduces the glare from the headlamps of the vehicle behind you. The dimming feature comes on and the indicator light illuminates each time the ignition is turned to start. Cleaning the Mirror Do not spray glass cleaner directly on the mirror.
Outside Power Foldaway Mirrors Vehicles with outside power foldaway mirrors have the controls located on the driver door armrest. Mirror Adjustment 1. Press (C) to fold the mirrors out to the driving position. 2. Press (D) to fold the mirrors in to the folded position.
Park Tilt Mirrors If the vehicle has the memory package, the outside mirrors have a park tilt feature. This feature tilts the outside mirrors to a preselected position when the vehicle is in R (Reverse). This allows the driver to view the curb for parallel parking.
{ CAUTION The Ultrasonic Rear Parking Assist (URPA) system does not replace driver vision. It cannot detect: • objects that are below the bumper, underneath the vehicle, or if they are too close or far from the vehicle • children, pedestrians, bicyclists, or pets.
The following describes how the URPA display lights appear as the vehicle gets closer to a detected object: Description English Metric amber light 8 ft 2.5 m amber/amber lights 40 in 1.0 m amber/amber/red lights 23 in 0.6 m amber/amber/red lights flashing 1 ft 0.
Rear Vision Camera (RVC) The vehicle may have a Rear Vision Camera system. Read this entire section before using it. { CAUTION The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: • Detect objects that are outside the camera’s field of view, below the bumper, or underneath the vehicle.
Turning the Rear Vision Camera System Of f or On To turn of f the rear vision camera system, press and hold z , located on the inside rearview mirror, until the left indicator light turns of f. The rear vision camera display is now disabled. To turn the rear vision camera system on again, press and hold z until the left indicator light illuminates.
There is a message on the rear vision camera screen that states “Check Surroundings for Safety”. Adjusting the Brightness and Contrast of the Screen To adjust the brightness and contrast of the screen, press the MENU button while the rear vision camera image is on the display.
Rear Vision Camera Location The camera is located above the license plate. The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper. The area displayed can vary depending on vehicle orientation or road conditions.
The rear vision camera system display in the rearview mirror may turn of f or not appear as expected due to one of the following conditions. If this occurs the left indicator light on the mirror will flash. • A slow flash may indicate a loss of video signal, or no video signal present during the reverse cycle.
Press the OnStar button to have an OnStar advisor contact Roadside Service. OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature.
OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days.
How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy.
Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules.
Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote.
2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit).
8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it.
Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Home Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to flash, after 20 seconds.
Center Console Storage Pull up on the lever, located on the front of the center console armrest, to slide it forward and backward. To open the armrest storage area, press the button located on the front of the armrest. There is additional storage under the armrest.
{ CAUTION Never open more than one of the three latches at a time to help avoid personal injury and damage to the console. Notice: Slide the front console as far forward as it will go before folding the second row console forward to help prevent damage to the consoles.
Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle can damage the vehicle. Load cargo so that it rests as far forward as possible and against the side rails, making sure to fasten it securely.
There is an additional storage compartment on each side of the system. To open, unlatch and lift the panel up. To remove the cargo management system: 1. Open the cover. It remains open when lifted. 2. Remove the side panels and place inside. 3. Loosen the retaining nuts on each side of the system by turning them counterclockwise.
Sunroof The vehicle may have a sunroof over the front seats and a rear sunroof over the second row seats. The rear sunroof does not open. The switches to operate the front sunroof and rear sunshade are located on the headliner above the rearview mirror.
Instrument Panel Instrument Panel Overview Instrument Panel Overview .... .3-4 Hazard Warning Flashers ...... .3-5 Horn ................................... .3-5 Tilt and Telescopic Steering Wheel .................. .3-6 Turn Signal/Multifunction Lever .
Fog Lamp Light .................. .3-45 Cruise Control Light ............ .3-45 Highbeam On Light ............. .3-46 Tow/Haul Mode Light .......... .3-46 Fuel Gage ......................... .3-46 Driver Information Center (DIC) Driver Information Center (DIC) .
✍ NOTES Instrument Panel 3-3.
Instrument Panel Overview 3-4 Instrument Panel.
The main components of the instrument panel are listed here: A. Outlet Adjustment on page 3-30 . B. Turn Signal/Multifunction Lever on page 3-6 . Windshield Wipers on page 3-7 . C. Instrument Panel Cluster on page 3-34 . D. Head-Up Display (HUD) on page 3-16 (If Equipped).
Tilt and Telescopic Steering Wheel The steering wheel can be adjusted. The adjustment lever is located on the left side of the steering column. Pull the lever down to move the steering wheel up or down and in or out. Pull the lever up to lock the steering wheel in place.
Turn Signal On Chime If either one of the turn signals are left on and the vehicle has been driven more than 3/4 mile (1.2 km), a chime will sound. Headlamp High/ Low-Beam Changer 23 Headlamp High/Low Beam Changer: Push the turn signal/multifunction lever away from you to turn the high beams on.
Windshield Washer J (Washer Fluid): Press the button located at the end of the turn signal/multifunction lever, to spray washer fluid on the windshield. The wipers clear the windshield and either stop or return to the preset speed. The ignition key must be in ACC/ACCESSORY or ON/RUN for this to work.
Rear Window Wiper/ Washer The rear wiper and rear wash button is located on the instrument panel below the climate control system. Z (Rear Wiper): Press to turn the rear wiper on and of f. The wiper speed cannot be changed. Y (Wash): Press to spray washer fluid on the rear window.
Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed.
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed.
2 (Headlamps): Turns the headlamps on together with the following lamps listed below. A warning chime sounds if the driver’s door is opened when the ignition switch is of f and the headlamps are on.
When the DRL are on, the regular headlamps, taillamps, sidemarker, and other lamps will not be on. The instrument panel and cluster will also not be lit. For vehicles with HID headlamps, if the DRL are on and the left or right turn signal lamp is turned on, the left or right DRL will go of f.
Dome Lamps The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. The lamps can also be turned on and of f by turning the instrument panel brightness control clockwise to the farthest position. Dome Lamp Override The dome lamp override button is located next to the exterior lamps control.
Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be of f for delayed exit lighting to work. When the key is removed, interior illumination activates and remains on until one of the following occurs: • The ignition is in ON/RUN.
EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories.
It will also display turn-by-turn navigation information if the vehicle has a navigation radio. The images are projected by the HUD lens located on the driver’s side of the instrument panel. The tap shift gear will also appear on the HUD if the vehicle has tap shift and it is active.
When the HUD is on, the speedometer reading is continually displayed. The current radio station or CD track number will display for a short period of time after the radio or CD track status changes.
Format Three: This display includes all the information in Format One along with a circular tachometer, but without outside air temperature. All formats will show the turn-by-turn navigation information and provide details about the next driving maneuver to be made.
Accessory Power Outlet(s) The vehicle has three 12-volt outlets which can be used to plug in electrical equipment, such as a cellular telephone, a compact disc player, etc. The power outlets are located on the instrument panel below the climate controls, at the rear of the center console, and in the rear cargo area.
Power Outlet 115 Volt Alternating Current For vehicles with this power outlet, it can be used to plug in electrical equipment that uses a maximum limit of 150 watts. The power outlet is located on the rear of the center console. An indicator light on the outlet turns on to show it is in use.
Climate Controls Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control B. Temperature Control C. Air Delivery Mode Control D. Air Conditioning E. REAR (Rear Climate Control) F. Recirculation G.
6 (Floor): Air is directed to the floor outlets, with some of the air directed to the windshield, side window, and second row floor outlets. In this mode, the system automatically selects outside air. Recirculation cannot be selected while in floor mode.
@ (Recirculation): Press to turn the recirculation mode on or of f. An indicator light comes on when recirculation is on. When the engine is turned of f, the recirculation mode automatically turns of f and must be re-selected when the engine is turned on again.
Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control B. AUTO C. Defrost D. Recirculation E. REAR (Rear Climate Control) F. Air Delivery Mode Control G. Driver Side Temperature Control H.
Automatic Operation AUTO (Automatic): The system automatically controls the inside temperature, the air delivery, and the fan speed. To use automatic mode: 1. Press the AUTO button. When AUTO is selected, the current temperature(s) selected and AUTO is shown on the display.
PASS (Passenger): Press to set the passenger temperature to match the driver temperature setting. The PASS indicator will turn of f. When the passenger temperature setting is dif ferent than the driver setting, the PASS indicator comes on. Manual Operation The air delivery mode or fan speed can be manually adjusted.
0 (Defrost): Press to turn the defrost on or of f. This mode quickly clears the windshield of fog or frost. Air is directed to the windshield, side window, and floor vents.
The recirculation mode cannot be used with floor, defog, or defrosting modes. If recirculation is selected in these modes, the indicator flashes three times and turns of f. The air conditioning compressor also comes on when this mode is activated. While in recirculation mode the windows can fog when the weather is cold and damp.
The interior temperature sensor located on the instrument panel to the right of the steering column, measures the temperature of the air inside the vehicle. There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle.
Rear Air Conditioning and Heating System A. Fan Control B. Temperature Control C. Air Delivery Mode Control For vehicles with the rear climate control system, the controls are located on the rear of the center console. The system can also be controlled with the front controls.
Rear Air Conditioning and Heating System and Electronic Climate Controls A. Fan Control B. Air Delivery Mode Control C. Temperature Control For vehicles with the rear climate control system, the controls are located on the rear of the center console.
N (Air Delivery Mode Control): Press to manually change the direction of the airflow. Repeatedly press the button until the desired mode appears on the display. H (Vent): Air is directed through the overhead outlets. ) (Bi-Level): Air is directed through the rear floor outlets, as well as the overhead outlets.
Instrument Panel Cluster The instrument cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel has been used, and many other things needed to drive safely and economically.
Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles or kilometers. This vehicle has a tamper-resistant odometer.
Airbag Readiness Light This light shows if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-50 .
If you are using remote start to start the vehicle from a distance, if equipped, you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or of f symbol to let you know the status of the right front passenger frontal airbag.
Voltmeter Gage When the engine is not running, but the ignition is turned on, this gage shows the battery’s state of charge in DC volts. When the engine is running, this gage shows the condition of the charging system. The vehicle’s charging system regulates voltage based on the state of charge of the battery.
This light may also come on due to low brake fluid. See Brakes on page 5-27 for more information. When the ignition is on, the brake system warning light will also come on when the parking brake is set. The light will stay on if the parking brake does not release fully.
StabiliTrak ® Indicator Light This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light goes of f. If it stays on, or comes on while driving, there could be a problem with the StabiliTrak system and the vehicle might need service.
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. Under normal driving conditions the gage will read approximately 210°F (100 °C) or less. If the gage pointer is near 260°F (125 °C), the engine is too hot. It means that the engine coolant has overheated.
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration.
The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem.
Highbeam On Light The highbeam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 3-7 for more information. Tow/Haul Mode Light This light comes on when the Tow/Haul mode has been activated. For more information, see Tow/Haul Mode on page 2-26 .
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. All messages will appear in the DIC display located at the top of the instrument panel cluster.
DIC Buttons The buttons are the set/reset, customization, vehicle information, and trip/fuel buttons. The button functions are detailed in the following pages. V (Set/Reset): Press this button to set or reset certain functions and to turn of f or acknowledge messages on the DIC.
See Engine Oil on page 5-13 . In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 6-3 for more information. Remember, you must reset the OIL LIFE display yourself after each oil change.
If a low or high tire pressure condition is detected by the system while driving, a message advising you to check the pressure in a specific tire will appear in the display. See Inflation - Tire Pressure on page 5-43 and DIC Warnings and Messages on page 3-58 for more information.
To switch between English and metric measurements, see “UNITS” earlier in this section. TRIP A and TRIP B Press the trip/fuel button until TRIP A or TRIP B displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for each trip odometer.
AVG (Average) ECONOMY Press the trip/fuel button until AVG ECONOMY displays. This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset.
DIC Operation and Displays (Without DIC Buttons) If your vehicle does not have DIC buttons, the information below explains the operation of this system. The DIC has dif ferent displays which can be accessed by pressing the trip odometer reset stem located on the instrument panel cluster.
To use the retro-active reset feature, press and hold the trip odometer reset stem for at least four seconds. The trip odometer will display the number of miles (mi) or kilometers (km) driven since the ignition was last turned on and the vehicle was moving.
If you choose OFF, the system will be turned of f. The URPA system automatically turns back on after each vehicle start. When the URPA system is turned of f and the vehicle is shifted out of P (Park), the DIC will display the PARK ASSIST OFF message as a reminder that the system has been turned of f.
DISPLAY LANGUAGE To access this display, the vehicle must be in P (Park). This display allows you to select the language in which the DIC messages will appear. To select a language: 1. Press the trip odometer reset stem until DISPLAY LANGUAGE displays.
3. Press the set/reset button to scroll through and select the appropriate variance zone. 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. 5. If calibration is necessary, calibrate the compass.
DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition.
BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping below expected levels. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed.
ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gage on page 3-41 . To avoid added strain on a hot engine, the air conditioning compressor automatically turns of f.
ENGINE POWER IS REDUCED This message displays and a chime sounds when the cooling system temperature gets too hot and the engine further enters the engine coolant protection mode. See Engine Overheating on page 5-24 for further information. This message also displays when the vehicle’s engine power is reduced.
LEFT REAR DOOR OPEN This message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn of f the vehicle, check the door for obstructions, and close the door again. Check to see if the message still appears on the DIC.
REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “Matching Transmitter(s) to Your Vehicle” under Remote Keyless.
SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument panel cluster. See Charging System Light on page 3-37 .
SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-41 .
THEFT ATTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Content Theft-Deterrent on page 2-16 for more information.
TURN SIGNAL ON This message displays and a chime sounds if a turn signal is left on for 3/4 of a mile (1.2 km). Move the turn signal/multifunction lever to the of f position. WASHER FLUID LOW ADD FLUID This message displays when the windshield washer fluid is low.
Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle: DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English.
AUTO DOOR LOCK This feature allows you to select when the vehicle’s doors will automatically lock. See Programmable Automatic Door Locks on page 2-9 for more information. Press the customization button until AUTO DOOR LOCK appears on the DIC display.
REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open.
DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle’s doors and liftgate will be delayed. When locking the doors and liftgate with the power door lock switch and a door or the liftgate is open, this feature will delay locking the doors and liftgate until five seconds after the last door is closed.
APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter. Press the customization button until APPROACH LIGHTING appears on the DIC display.
PARK TILT MIRRORS If your vehicle has this feature, it allows you to select whether or not the outside mirror(s) will automatically tilt down when the vehicle is shifted into R (Reverse). See Outside Power Foldaway Mirrors on page 2-33 for more information.
MEMORY SEAT RECALL If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat and Mirrors on page 1-6 for more information. Press the customization button until MEMORY SEAT RECALL appears on the DIC display.
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION Taking your eyes of f the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
5. To decrease the time or date, do one of the following: • Press © SEEK. • Press s REV. • Turn f counter-clockwise. To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/ day/year to day/month/year: 1.
The vehicle may have one of these radios as its audio system. Radios with CD and DVD Radios with CD and DVD have a Bose ® Surround Sound System. Some of its features are explained later in this section under, “Adjusting the Speakers (Balance/Fade)”.
Playing the Radio O (Power/Volume): Press to turn the system on and of f. Turn to increase or decrease the volume. For vehicles with a Rear Entertainment System (RSE), press and hold for more than two seconds to turn of f the entire radio and RSE system and to start the parental control feature.
Finding a Station BAND: Press to switch between AM, FM, or XM. The selection displays. f (Tune): Turn to select radio stations. © SEEK ¨ : Press to go to the previous or to the next station and stay there. To scan stations, press and hold © or ¨ until a beep sounds.
To setup the number of favorites pages: 1. Press MENU to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label. 3. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers.
To quickly adjust bass, midrange, or treble to the middle position, press the pushbutton positioned under the BASS, MID, or TREB label for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all tone and speaker controls to the middle position, press f for more than two seconds until a beep sounds.
Finding a Category (CAT) Station CAT (Category): The CAT button is used to find XM™ stations when the radio is in the XM mode. To find XM channels within a desired category: 1. Press BAND until the XM frequency displays. 2. Press CAT to display the category labels.
Radio Messages Calibration Error: The audio system has been calibrated for the vehicle from the factory. If Calibration Error displays, it means that the radio has not been configured properly for the vehicle and it must be returned to your dealer/retailer for service.
The CD is controlled by the buttons on the radio faceplate or by the RSA unit. See Rear Seat Audio (RSA) on page 3-125 for more information. The DVD/CD decks, (upper slot is the DVD deck and the lower slot is the CD deck) of the radio are compatible with most audio CDs, CD-R, CD-RW, and MP3/WMAs.
Care of the CD and DVD Player Do not add any label to a CD, it could get caught in the CD or DVD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen.
FWD (Fast Forward): Press and hold to advance playback quickly within a track. Sound will be heard at a reduced volume. Release to resume playing the track. The elapsed time of the track displays. RDM (Random): CD tracks can be listened to in random, rather than sequential order with the random setting.
Radios with CD and DVD Audio Output Only one audio source can be heard through the speakers at one time. An audio source is defined as DVD slot, CD slot, XM, FM/AM, Front Auxiliary Jack, or Rear Auxiliary Jack. Press O to turn the radio on. The radio can be heard through all of the vehicle speakers.
Player Error: There are disc LOAD or disc EJECT problems. • It is very hot. When the temperature returns to normal, the CD should play. • The road is very rough. When the road becomes smoother, the CD should play. • The CD is dirty, scratched, wet, or upside down.
s REV (Fast Reverse): Press to quickly reverse the DVD at five times the normal speed. The radio displays the elapsed time while in fast reverse. To stop fast reversing, press again. This button may not work when the DVD is playing the copyright information or the previews.
c (Stop): Press to stop playing, rewinding, or fast forwarding a DVD. r (Enter): Press to select the choices that are highlighted in any menu. y (Menu): Press to access the DVD menu. The DVD menu is dif ferent on every DVD. Use the pushbuttons located under the navigation arrows to navigate the cursor through the DVD menu.
Inserting a Disc To play a disc, gently insert the disc, with the label side up, into the loading slot. The DVD player might not accept some paper labeled media. The player starts loading the disc into the system and shows “Loading Disc” on the radio display.
DVD Radio Error Messages Player Error: This message displays when there are disc load or eject problems. Disc Format Error: This message displays, if the disc is inserted with the disc label wrong side up, or if the disc is damaged. Disc Region Error: This message displays, if the disc is not from a correct region.
DVD/CD AUX (Auxiliary): Press to select between DVD, CD, or Auxiliary. • If an auxiliary input device is not connected, “No Aux Input Device” displays. • When a disc is in either slot, the DVD/CD text label and a message showing the track or chapter number displays.
Compressed Audio The radio also plays discs that contain both uncompressed CD audio (.CDA files) and MP3/WMA files. The radio plays both file formats in the order in which they were recorded to the disc. MP3/WMA Format Creating an MP3/WMA disc on a personal computer: • Make sure the MP3/WMA files are recorded on a CD-R or CD-RW disc.
Root Directory The root directory of the CD-R or CD-RW is treated as a folder. If the root directory has compressed audio files, the directory displays as the CD label. All files contained directly under the root directory are accessed prior to any root directory folders.
File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name. Track names longer than 32 characters or four pages are shortened.
RDM (Random): With the random setting, MP3/WMA files on the CD-R or CD-RW can be listened to in random, rather than sequential order. To play MP3/WMA files from the CD-R or CD-RW in random order, press the pushbutton positioned under the RDM label until Random Current Disc displays.
Using an MP3 (Radio with CD and DVD Player) MP3/WMA CD-R or CD-RW Disc Compressed Audio or Mixed Mode Discs The radio also plays discs that contain both uncompressed CD audio (.CDA files) and MP3/WMA files depending on which slot the disc is loaded into.
Root Directory The root directory of the CD-R or CD-RW disc is treated as a folder. If the root directory has compressed audio files, the directory is displayed as F1 ROOT. All files contained directly under the root directory are accessed prior to any root directory folders.
File System and Naming The song name that is displayed is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name. Track names longer than 32 characters or four pages are shortened.
Z DVD (Eject): Press and release this button to eject the CD-R or CD-RW that is currently playing in the top slot. A beep sounds and Ejecting Disc displays.
h (Music Navigator): Use the music navigator feature to play MP3/WMA files on the CD-R or CD-RW in order by artist or album. Press the pushbutton located below the music navigator label. The player scans the disc to sort the files by artist and album ID3 tag information.
If a disc is in both the DVD slot and the CD slot the DVD/CD AUX button cycles between the two sources and does not indicate “No Aux Input Device”. If a front auxiliary device is connected, the DVD/CD AUX button cycles through all available options, such as: DVD slot, CD slot, Front Auxiliary, and Rear Auxiliary (if available).
No CAT Info: No category information is available at this time on this channel. The system is working properly. No Information: No text or informational messages are available at this time on this channel. The system is working properly. CAT Not Found: There are no channels available for the selected category.
Voice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags. Noise: Keep interior noise levels to a minimum. The system may not recognize voice commands if there is too much background noise.
Pairing A Bluetooth enabled cell phone must be paired to the in-vehicle Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone.
Listing All Paired and Connected Phones 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices.
Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please” followed by a tone.
4. After the complete number has been entered, say “Store”. The system responds with “Please say the name tag” followed by a tone. 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store <name tag>.
Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar (if present). To use the delete all name tags command: 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone.
4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds with “OK, Dialing” and dials the number. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number.
Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. • Press b g to answer an incoming call when another call is active. The original call is placed on hold. • Press b g again to return to the original call.
Transferring a Call Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press b g . The system responds with “Ready” followed by a tone.
Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers and numbers stored as name tags during a call. This is used when calling a menu driven phone system. Account numbers can be programmed into the phonebook for retrieval during menu driven calls.
Clearing the System Unless information is deleted out of the in-vehicle Bluetooth system, it will be retained indefinitely. This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see the above sections on Deleting a Paired Phone and Deleting Name Tags.
In severe or extreme weather conditions the RSE system might or might not work until the temperature is within the operating range. The operating range for the RSE system is above − 4°F ( − 20°C) or below 140°F (60°C).
For optimal audio performance, the headphones must be worn correctly. Headphones should be worn with the headband over the top of the head for best audio reception. The symbol L (Left) appears on the upper left side, above the ear pad and should be positioned on the left ear.
The A/V jacks are color coded to match typical home entertainment system equipment. The yellow jack (A) is for the video input. The white jack (B) is for the left audio input. The red jack (C) is for the right audio input. Power for auxiliary devices is not supplied by the radio system.
Video Screen The video screen is located in the overhead console. When the video screen is not in use, push it up into its locked position. To use the video screen: 1. Push the release button located on the overhead console. 2. Move the screen to the desired position.
Remote Control Buttons O (Power): Press to turn the video screen on and of f. P (Illumination): Press to turn the remote control backlight on. The backlight automatically times out after seven to ten seconds if no other button is pressed while the backlight is on.
Depending on the radio, perform reverse slow play by pressing s then r . To cancel slow play mode, press s again. t (Previous Track/Chapter): Press to return to the start of the current track or chapter. Press again to go to the previous track or chapter.
Battery Replacement To change the remote control batteries: 1. Slide the rear cover back, on the remote control. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment.
Problem Recommended Action Sometimes the wireless headphone audio cuts out or buzzes. Check for obstructions, low batteries, reception range, and interference from cellular telephone towers or by using a cellular telephone in the vehicle. Check that the headphones are on correctly using the L (left) and R (right) on the headphones.
Rear Seat Audio (RSA) For vehicles with Rear Seat Audio (RSA), rear seat passengers can listen to and control any of the music sources: radio, CDs, DVDs, or other auxiliary sources. The rear seat passengers can only control the music sources the front seat passengers are not listening to (except on some radios where dual control is allowed).
P (Power): Press to turn the RSA on or of f. Volume: Turn to increase or to decrease the volume of the wired headphones. The left knob controls the left headphones and the right knob controls the right headphones.
When a disc is playing in the CD or DVD changer, press PROG to select the next disc, if multiple discs are loaded. This function is inactive, with some radios, if the front seat passengers are listening to the disc. When a DVD video menu is being displayed, press PROG to perform the ENTER menu function.
Audio Steering Wheel Controls Vehicles with audio steering wheel controls could dif fer depending on the vehicle’s options. Some audio controls can be adjusted at the steering wheel. w (Next): Press to go to the next radio station stored as a favorite, or the next track if a CD/DVD is playing.
AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. For better radio reception, most AM radio stations boost the power levels during the day, and then reduce these levels during the night.
✍ NOTES 3-130 Instrument Panel.
Driving Your Vehicle Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy ........................... .4-1 Defensive Driving ................. .4-2 Drunk Driving ...................... .4-2 Control of a Vehicle .............. .4-3 Braking .
• Keep vehicle tires properly inflated. • Combine several trips into a single trip. • Replace the vehicle’s tires with the same TPC Spec number molded into the tire’s sidewall near the size. • Follow recommended scheduled maintenance. Defensive Driving Defensive driving means “always expect the unexpected.
Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured.
And, of course, actual stopping distances vary greatly with the surface of the road, whether it is pavement or gravel; the condition of the road, whether it is wet, dry, or icy; tire tread; the condition of the brakes; the weight of the vehicle; and the amount of brake force applied.
As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance.
If the system fails to turn on or activate, the StabiliTrak light along with one of the following messages will be displayed on the Driver Information Center (DIC): TRACTION CONTROL OFF, SERVICE TRACTION CONTROL, SERVICE STABILITRAK.
Traction Control Operation The traction control system is part of the StabiliTrak system. Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary.
To restore the AWD operation and prevent excessive wear on the AWD system, replace the compact spare with a full-size tire as soon as possible. See Compact Spare Tire on page 5-79 for more information.
An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o’clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up.
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive.
Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle’s tires so they actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Hill and Mountain Roads Driving on steep hills or through mountains is dif ferent than driving on flat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all fluid levels and brakes, tires, cooling system, and transmission.
The StabiliTrak ® System on page 4-5 improves the ability to accelerate on slippery roads, but slow down and adjust your driving to the road conditions. When driving through deep snow, turn of f the traction control part of the StabiliTrak ® System to help maintain vehicle motion at lower speeds.
CAUTION (Continued) For more information about carbon monoxide, see Engine Exhaust on page 2-30 . Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn of f any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible.
With the driver’s door open, you will find the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
A. Vehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg). B. Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg). C. Available Occupant and Cargo Weight = 700 lbs (317 kg). A. Vehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg).
Refer to your vehicle’s tire and loading information label for specific information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight.
If you put things inside your vehicle — like suitcases, tools, packages, or anything else, they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. { CAUTION Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.
Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground.
For vehicles being dinghy towed, the vehicle should be run at the beginning of each day and at each RV fuel stop for about five minutes. This will ensure proper lubrication of transmission components. Re-install the fuse to start the vehicle. To tow the vehicle from the front with all four wheels on the ground: 1.
Dolly Towing (All-Wheel-Drive Vehicles) All-wheel-drive vehicles must not be towed with two wheels on the ground. To properly tow these vehicles, they should be placed on a platform trailer with all four wheels of f of the ground or dinghy towed from the front.
Towing the Vehicle From the Rear Notice: Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the vehicle warranty. Never have the vehicle towed from the rear.
Trailering is dif ferent than just driving the vehicle by itself. Trailering means changes in handling, acceleration, braking, durability and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly. The following information has many time-tested, important trailering tips and safety rules.
Weight of the Trailer How heavy can a trailer safely be? It depends on how the rig is used. For example, speed, altitude, road grades, outside temperature and how much the vehicle is used to pull a trailer are all important. It can depend on any special equipment on the vehicle, and the amount of tongue weight the vehicle can carry.
weight the vehicle can tow. If towing a trailer, the tongue load must be added to the GVW because the vehicle will be carrying that weight, too. See Loading the Vehicle on page 4-16 for more information about the vehicle’s maximum load capacity.
If the vehicle has many options and there is a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well. 300 lbs (136 kg) could be added to the front axle weight and 400 lbs (181 kg) to the rear axle weight.
• Will any holes be made in the body of the vehicle when the trailer hitch is installed? If there are, then be sure to seal the holes later when the hitch is removed. If the holes are not sealed, dirt, water, and deadly carbon monoxide (CO) from the exhaust can get into the vehicle.
Passing More passing distance is needed when towing a trailer. Because the rig is longer, it is necessary to go much farther beyond the passed vehicle before returning to the lane. Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, move that hand to the left.
Tow/Haul Mode Tow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load. The purpose of the Tow/Haul mode is to: • Reduce the frequency and improve the predictability of transmission shifts when pulling a heavy trailer or a large or heavy load.
Parking on Hills { CAUTION Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.
The harness connector can be plugged into a seven-pin universal heavy-duty trailer connector available through your dealer/retailer. The seven-wire harness contains the following trailer circuits: •.
✍ NOTES 4-34 Driving Your Vehicle.
Service and Appearance Care Service Service ............................... .5-3 Accessories and Modifications ...................... .5-3 California Proposition 65 Warning ............................ .5-4 California Perchlorate Materials Requirements .
When It Is Time for New Tires ........................ .5-51 Buying New Tires ............... .5-52 Dif ferent Size Tires and Wheels ............................ .5-53 Uniform Tire Quality Grading ........................... .5-54 Wheel Alignment and Tire Balance .
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories an.
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can af fect the airflow around it. This can cause wind noise and can af fect fuel economy and windshield washer performance. Check with your dealer/retailer before adding equipment to the outside of the vehicle.
California Fuel If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications.
We recommend that you use these gasolines, if they comply with the specifications described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: This vehicle was not designed for fuel that contains methanol.
Filling the Tank { CAUTION Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn of f the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle.
{ CAUTION Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { CAUTION Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense fuel only into approved containers.
Hood Release To open the hood, do the following: 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver’s side of the vehicle. 2. At the front of the vehicle, pull up on the center of the hood, and push the secondary hood release to the right.
Engine Compartment Overview When you lift the hood, here is what you will see: 5-12 Service and Appearance Care.
A. Radiator Pressure Cap. See Cooling System on page 5-19 . B. Engine Coolant Recovery Cap. See Cooling System on page 5-19 . C. Remote Negative ( − ) Terminal. See Jump Starting on page 5-30 . D. Underhood Fuse Block on page 5-90 . E. Remote Positive (+) Terminal.
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-94 .
• GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness.
When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A CHANGE ENGINE OIL SOON message comes on.
What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner.
How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter (away from vehicle) to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required.
The transmission fluid will not reach the end of the dipstick unless the transmission is at operating temperature. If you need to check the transmission fluid level, please take the vehicle to your dealer/retailer. Cooling System The cooling system allows the engine to maintain the correct working temperature.
What to Use { CAUTION Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture.
The coolant recovery tank cap has this symbol on it. When the engine is cold, the coolant level should be at or above the FULL COLD line marked on the recovery tank.
How to Add Coolant to the Radiator { CAUTION An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
6. Fill the coolant recovery tank to the FULL COLD mark. 7. Reinstall the cap on the coolant recovery tank but leave the radiator pressure cap of f. 8. Start the engine and let it run until the upper radiator hose feels warm. Any time during this procedure, watch out for the engine cooling fan(s).
Engine Overheating The vehicle has several indicators to warn of engine overheating. There is an engine coolant temperature gage on the instrument panel cluster.
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: • Climbs a long hill on a hot day.
Power Steering Fluid The power steering fluid reservoir is located toward the front of the engine compartment on the passenger side of the vehicle. See Engine Compartment Overview on page 5-12 for reservoir location.
Adding Washer Fluid When the windshield washer fluid reservoir is low, a WASHER FLUID LOW ADD FLUID message will be displayed on the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-58 for more information. Open the cap with the washer symbol on it.
There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up. • A fluid leak in the brake hydraulic system can also cause a low fluid level.
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
Battery This vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. For battery replacement, see your dealer/retailer or the service manual.
Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
4. Open the hoods and locate the positive (+) and negative ( − ) terminal locations on the other vehicle. Your vehicle has a remote positive (+) and a remote negative ( − ) jump starting terminal. See Engine Compartment Overview on page 5-12 for more information on the terminal locations.
6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
10. Now start the vehicle with the good battery and run the engine for a while. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service. Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle.
All-Wheel Drive It is recommended that the all-wheel drive lubricants be checked and filled by the dealer/retailer. When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See Scheduled Maintenance on page 6-3 .
License Plate Lamp To replace one of these bulbs: 1. Remove the two screws holding each of the license plate lamps to the liftgate trim. 2. Turn and pull the license plate lamp forward through the lift gate trim opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
3. Install the new wiper blade and make sure the wiper blade locks into place. For the proper size and type see Maintenance Replacement Parts on page 6-14 . Backglass Wiper Blade To replace the backglass wiper blade: 1. Pull the wiper blade assembly away from the backglass.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall.
(A) Temporary Use Only : The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat.
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Bead : The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire : A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.
Maximum Loaded Vehicle Weight : The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight : The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-16 .
Vehicle Capacity Weight : The number of designated seating positions multiplied by 150 lbs (68 kg) plus the rated cargo load. See Loading the Vehicle on page 4-16 . Vehicle Maximum Load on the Tire : Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight.
When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, if the vehicle has one. It should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 5-79 .
As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated.
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument panel cluster. At the same time a message to check the pressure in a specific tire appears on the Driver Information Center (DIC) display.
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire’s air pressure. If increasing the tire’s air pressure, do not exceed the maximum inflation pressure indicated on the tire’s sidewall.
Tire Inspection and Rotation We recommend that you regularly inspect the vehicle’s tires, including the spare tire, if the vehicle has one, for signs of wear or damage. See When It Is Time for New Tires on page 5-51 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
{ CAUTION Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come of f and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
With proper care and maintenance tires typically wear out before they degrade due to age. If you are unsure about the need to replace the tires as they get older, consult the tire manufacturer for more information. Buying New Tires GM has developed and matched specific tires for your vehicle.
{ CAUTION If you use bias-ply tires on the vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A Th.
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
If you need to replace any of your wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, wheel nuts, and TPMS sensors for your vehicle.
CAUTION (Continued) To help avoid damage to the vehicle, drive slowly, readjust or remove the device if it is contacting the vehicle, and do not spin the vehicle’s wheels. If you do find traction devices that will fit, install them on the front tires.
Tire Sealant and Compressor Kit { CAUTION Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.
This vehicle may have one of the following tire sealant and compressor kits. The kit includes: A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gage D. Pressure Deflation Button (If equipped) E. Tire Sealant Canister F. Sealant/Air Hose (Clear) G.
Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes.
2. Unwrap the sealant/air hose (F) and the power plug (H). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the valve stem cap from the flat tire by turning it counterclockwise.
Notice: If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve.
If the tire pressure has not dropped more than 10 psi (68 kPa) from the recommended inflation pressure, inflate the tire to the recommended inflation pressure.
Always do a safety check first. See If a Tire Goes Flat on page 5-57 . 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 5-66 . 2. Unwrap the air only hose (G) and the power plug (H).
If you inflate the tire higher than the recommended pressure you can adjust the excess pressure by pressing the pressure deflation button (D), if equipped, until the proper pressure reading is reached. This option is only functional when using the air only hose (G).
Tire Sealant and Compressor Kit Storage The tire sealant and compressor kit is located in the storage compartment on the driver side, at the rear of the vehicle. 1. Press down on the latch tab and pull the cover of f to access the storage compartment.
When the vehicle has a flat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A). A. Wheel Block B. Flat Tire The following information explains how to use the jack and change a tire.
Removing the Spare Tire The compact spare tire is located under the vehicle, in front of the rear bumper. See Compact Spare Tire on page 5-79 for more information about the compact spare. A. Rear Convenience Center B. Lug Wrench C. Storage Compartment Cap Hole D.
6. Turn the wrench clockwise to raise the cable back up after removing the spare tire. Do not store a full-size or a flat road tire under the vehicle. See Storing a Flat or Spare Tire and Tools on page 5-76 . To continue changing the flat tire, see Removing the Flat Tire and Installing the Spare Tire on page 5-70 .
Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 5-66 for more information. 2. If the vehicle has a wheel cover, loosen the plastic nut caps with the wheel wrench. They will not come of f.
Notice: If a jack is used to raise the vehicle without positioning it correctly, the vehicle could be damaged. When raising the vehicle on a jack, avoid contact with the rear axle control arms. 5. Do not raise the vehicle yet. Put the compact spare tire near you.
9. Remove the plastic spare tire heat shield by pulling the rubber latch. Store the plastic spare tire heat shield. See Storing a Flat or Spare Tire and Tools on page 5-76 for more information. { CAUTION Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
13. Lower the vehicle by attaching the lug wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. { CAUTION Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come of f.
Secondary Latch System This vehicle has an underbody mounted tire hoist assembly that has a secondary latch system. It is designed to stop the compact spare tire from suddenly falling of f the vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down.
5. Turn the lug wrench clockwise to raise the jack until it lifts the secondary latch spring. 6. Keep raising the jack until the spare tire stops moving upward and is held firmly in place. This lets you know that the secondary latch has released and the spare tire is balancing on the jack.
Storing a Flat or Spare Tire and Tools Storing the Spare Tire { CAUTION The underbody-mounted spare tire needs to be stored with the valve stem pointing down. If the spare tire is stored with the valve stem pointing upwards, the secondary latch will not work properly and the spare tire could loosen and suddenly fall from the vehicle.
6. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire. If the tire moves, use the lug wrench to tighten the cable.
8. Make sure the metal tube is centered at the striker. Push the tube toward the front of the vehicle. 9. Close the liftgate and make sure it is latched properly. Storing the Tools A. Tool Bag B. Wing Bolt C. Jack Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on.
Compact Spare Tire { CAUTION Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured.
Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces.
• Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide. Use only mild, neutral-pH soaps. • Too much cleaner that saturates the upholstery.
Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather.
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 6-12 .
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer/retailer. If the vehicle has a basecoat/ clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat.
Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for the vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle.
Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty. Some add-on electrical equipment can keep other components from working as they should.
Fuses Usage AIRBAG Airbag AMP Amplifier BCK/UP/ STOP Back-up Lamp/Stoplamp BCM Body Control Module CNSTR/ VENT Canister Vent CTSY Courtesy DR/LCK Door Locks DRL Daytime Running Lamps DRL 2 GMC HID On.
Relays Usage LT/PWR/ SEAT Driver Side Power Seat Relay RT/PWR/ SEAT Passenger Side Power Seat Relay Relays Usage PWR/ WNDW Power Windows Relay PWR/ COLUMN Power Steering Column Relay L/GATE Liftgate R.
Fuses Usage A/C CLUTCH Air Conditioning Clutch ABS MTR Antilock Braking System (ABS) Motor AFS Adaptive Forward Lighting System Fuses Usage AIRBAG Airbag System AUX POWER Auxiliary Power AUX VAC PUMP .
Fuses Usage HTD MIR Heated Outside Rearview Mirror HVAC BLWR Heating, Ventilation and Air Conditioning Blower LT HI BEAM Left High-Beam Headlamp LT LO BEAM Left Low-Beam Headlamp LT PRK Left Parking L.
Relays Usage FAN 3 Cooling Fan 3 FOG LAMP Fog Lamps HI BEAM High-Beam Headlamps HID/LO BEAM High Intensity Discharge (HID) Low-Beam Headlamps HORN Horn IGN Ignition Main LT TRLR STOP/TRN Trailer Left .
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information.
Maintenance Schedule Maintenance Schedule Introduction ......................... .6-1 Maintenance Requirements .... .6-1 Your Vehicle and the Environment ....................... .6-1 Using the Maintenance Schedule ........................... .6-2 Scheduled Maintenance .
To help protect the environment, and to keep the vehicle in good condition, be sure to maintain the vehicle properly. Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it.
To purchase service information, see Service Publications Ordering Information on page 7-15 . Owner Checks and Services on page 6-9 tells what should be checked, when to check it, and what can easily be done to help keep the vehicle in good condition.
Maintenance I —U s e Maintenance I if the CHANGE ENGINE OIL SOON message displays within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II —U s e Maintenance II if the previous service performed was Maintenance I .
Scheduled Maintenance (cont’d) Service Maintenance I Maintenance II Inspect brake system. See footnote (a). •• Check engine coolant and windshield washer fluid levels and add fluid as needed. •• Perform any needed additional services. See “Additional Required Services” in this section.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Engine cooling system service (or every five years, whichever occurs first).
(e) Make sure the safety belt reminder light and safety belt assemblies are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure vehicle safety, dependability, and emission control performance. Your dealer/ retailer can assist with these checks and services. Be sure any necessary repairs are completed at once.
At Least Once a Year Starter Switch Check { CAUTION When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Parking Brake and Automatic Transmission P (Park) Mechanism Check { CAUTION When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Usage Fluid/Lubricant Key Lock Cylinders Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Carrier Assembly — Dif ferential (Rear Drive Module) and Transfer Case (Power Transfer Unit) SAE 75W-90 Synthetic Axle Lubricant (GM Part No.
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 15278634 — Engine Oil Filter 89017524 PF48 Spark Plugs 12611882 41-107 Wiper Blades Driver – 24.
Engine Drive Belt Routing 3.6L V6 Engine Maintenance Schedule 6-15.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-1 . Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed Maintenance Schedule 6-17.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-18 Maintenance Schedule.
Customer Assistance Information Customer Assistance and Information Customer Satisfaction Procedure .......................... .7-1 Online Owner Center ............ .7-3 Customer Assistance for Text Telephone (TTY) Users ..............................
STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the U.S., call the GMC Consumer Relations Manager at 1-800-GMC-8782 (1-800-462-8782, Customer Assistance prompt).
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps One and Two, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program.
Other Helpful Links: GMC — www.gmc.com GMC Merchandise — www.gmccollection.com Help Center — www.gmc.com/helpcenter • FAQ • Contact Us My GM Canada (Canada) — www.
Customer Assistance Of fices GMC encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail GMC, the letter should be addressed to: United States GMC Customer Assistance Center P.O. Box 33172 Detroit, MI 48232-5172 www.
The of fer is available for a very limited period of time from the date of vehicle purchase/lease. For more details, or to determine your vehicle’s eligibility, visit gmmobility.com or call the GM Mobility Assistance Center at 1-800-323-9935. Text telephone (TTY) users, call 1-800-833-9935.
Services Provided • Emergency Fuel Delivery: Delivery of enough fuel for the vehicle to get to the nearest service station. • Lock-Out Service: Service is provided to unlock the vehicle if you are locked out. A remote unlock may be available if you have OnStar ® .
Services Specific to Canadian Purchased Vehicles • Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. • Lock-Out Service: Vehicle registration is required.
Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to of fer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada) and extended powertrain, and hybrid specific warranty in both the U.
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair. Rental reimbursement will be limited and must be supported by original receipts.
Recycled original equipment parts may also be used for repair. These parts are typically removed from vehicles that were total losses in prior crashes.
If a Crash Occurs Here is what to do if you are involved in a crash. • Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. • If there has been an injury, call emergency services for help.
• Choose a reputable collision repair facility for your vehicle. Whether you select a dealer/ retailer or a private collision repair facility to fix the damage, make sure you are comfortable with them. Remember, you will have to feel comfortable with their work for a long time.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traf fic Safety Administration (NHTSA) in addition to notifying General Motors.
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks.
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven.
GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an of ficial request of police or similar government of fice; as part of GM’s defense of litigation through the discovery process; or, as required by law.
✍ NOTES 7-18 Customer Assistance Information.
A Accessories and Modifications ...................... 5 - 3 Accessory Power ................. 2-21 Accessory Power Outlets ...... 3-20 Adding Equipment to Y our Airbag-Equipped V ehicle .... 1-62 Additional Required Services, Scheduled Maintenance .
B Battery ............................... 5-30 Electric Power Management ................. 3-15 Run-Down Protection ......... 3-16 Belt Routing, Engine ............. 6-15 Bluetooth ® ......................... 3-105 Brake Emergencies .................
Cleaning Aluminum or Chrome-Plated Wheels ........................ 5-85 Exterior Lamps/Lenses ...... 5-83 Fabric/Carpet ................... 5-81 Finish Care ...................... 5-84 Instrument Panel, Vinyl, and Other Plastic Surfaces ..............
Drive Systems All-Wheel Drive ................ 5-35 Driver Seat Height Adjuster ........... 1 - 3 Driver Information Center (DIC) .................... 3-47 DIC Operation and Displays ............... 3-47, 3-53 DIC V ehicle Customization ..............
F Filter Engine Air Cleaner ............ 5-17 Finish Damage .................... 5-86 Flashers, Hazard W arning ....... 3 - 5 Flash-to-Pass ........................ 3 - 7 Flat Tire .............................. 5-57 Flat Tire, Changing ..............
Hood Checking Things Under ..... 5-10 Release .......................... 5-11 H o r n .................................... 3 - 5 How to Wear Safety Belts Properly .......................... 1-19 I Ignition Positions .................. 2-20 Infants and Y oung Children, Restraints .
Lower Anchors and T ethers for Children ...................... 1-38 Luggage Carrier ................... 2-51 Lumbar Manual Controls ................. 1 - 4 Power Controls .................. 1 - 5 M Maintenance Footnotes .......................... 6 - 7 Maintenance Schedule Additional Required Services .
P Paint, Damage ..................... 5-86 Parade Dimming .................. 3-15 Park Shifting Into ..................... 2-28 Shifting Out of .................. 2-29 Park Aid ............................. 2-34 Park T ilt Mirrors ................... 2-34 Parking Assist .
Rear Seat Armrest ............... 2-52 Rear Seat Audio (RSA) System .......................... 3-125 Rear Seat Entertainment System .......................... 3-116 Rear Seat Operation ............ 1-10 Rear Vision Camera (R VC) .... 2-37 Rear Window W asher/Wiper .
Seats Driver Seat Height Adjuster ......................... 1 - 3 Head Restraints ................. 1 - 2 Heated and Cooled Seats .... 1 - 6 Heated Seats ..................... 1 - 5 Manual Lumbar .................. 1 - 4 Memory , Mirrors .............
T T achometer ......................... 3-35 T elescopic Wheel ................... 3 - 6 T ext T elephone (TTY) Users .... 7 - 4 Theft-Deterrent Feature ....... 3-127 Theft-Deterrent Systems ........ 2-16 Content Theft-Deterrent ..... 2-16 P ASS-Key ® III+ Electronic Immobilizer .
V V ehicle Control ............................. 4 - 3 Loading ........................... 4-16 Running While Parked ....... 2-30 Symbols .............................. i i i V ehicle Customization, DIC .... 3-67 V ehicle Data Recording and Privacy ..
Overview ........................................................ 1 - 1 Overview .................................................. 1 - 2 Features and Controls ..................................... 2 - 1 Features and Controls .........................
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, BUICK, the BUICK Emblem, GMC and the GMC Truck Emblem, PONTIAC, the PONTIAC Emblem, and the names EQUINOX, LUCERNE and TORRENT are registered trademarks; the names ENCLAVE, TRAVERSE, and ACADIA are trademarks of General Motors Corporation.
SATURN, the SATURN Emblem and the name VUE and VUE Two-Mode Hybrid are registered trademarks; the name OUTLOOK is a trademark of Saturn Corporation. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc. Dolby ® is manufactured under license from Dolby ® Laboratories.
✍ NOTES iv.
Overview ........................................................ .1-2 Navigation System Overview ........................... .1-2 Getting Started .............................................. .1-4 Cleaning the Video Screen ..........................
Overview Navigation System Overview Screen shown with Map Disc Inserted 1-2.
A. Map DVD Slot. See “Installing the Map DVD” under Maps on page 2-4 for more information. B. FULL MAP Touch Screen Button. See “NAV” under “Hard Keys” under Using the Navigation System on page 2-2 for more information. C. No GPS Symbol. See Symbols on page 2-7 for more information.
U. ¨ SEEK Key (Next). See Navigation Audio System on page 3-2 for more information. V. © SEEK Key (Previous). See Navigation Audio System on page 3-2 for more information. W. 1 (Zoom Out) Touch Screen Button. See “Map Scales” under Maps on page 2-4 for more information.
{ CAUTION: Avoid looking too long or too often at the moving map on the navigation screen. This could cause a crash and you or others can be injured or killed. Use the turn-by-turn voice guidance directions whenever possible. Use the navigation system to: • Plan a route.
After you acknowledge the start up information you will be able to access the NAV (navigation) and DEST (destination) functions. Once accessed, you can enter or delete information in the navigation system or access other functions. See instructions later in this section.
Limit Features While Driving The navigation system may have this feature. Touch the Limit Features While Driving screen button to turn on and of f the ability to limit functions while driving.
Entering a Destination by Using Address, Point of Interest, Previous Destination, or the Map Method and Storing Preset Destinations Entering an Address To enter a destination by entering the city name first: 1. If the radio is on with a map disc inserted, skip to Step 5.
10. Once a street has been selected, select the House # screen button to enter the house number. The system displays the house number range that is available for the street. 11. Select the Go screen button. A map screen, with the destination marked appears.
10. Select the route preference (Fastest, Shortest, or Other). The system calculates and highlights the route. 11. Select the Start Guidance screen button. The fastest route will automatically begin if the car starts moving forward. See “Point of Interest (POI)” under Destination on page 2-13 for more information.
6. Select the Map screen button after entering the destination. 7. Select the Mark screen button from the map. The address book screen appears. Five preset destinations can be stored, but you must set them from the Address Book screen. There are other ways to get to the Address Book as well.
7. Select the route preference (Fastest, Shortest, or Other). The system calculates and highlights the route. 8. Select the Start Guidance screen button. The fastest route will automatically begin if the car starts moving forward. See “Preset Destination” under Destination on page 2-13 for more information.
Features and Controls ..................................... .2-2 Using the Navigation System .......................... .2-2 M a p s ........................................................... .2-4 Symbols .............................................
Features and Controls Using the Navigation System This section includes basic information to operate the navigation system. Use the hard keys and the touch-sensitive screen buttons on the navigation screen to operate the system. See Navigation System Overview on page 1-2 for more information.
FAV (Favorite): Press to access the preset stations. See “Storing Radio Station Presets” under Navigation Audio System on page 3-2 for more information. AUDIO: Press to access the full Audio screen to change AM, FM, XM™ Satellite Radio Service (if equipped), CD, DVD, if equipped, and auxiliary input.
Maps This section includes basic information about the map database. Map Coverage The maps are stored on a DVD. The United States, Canada, Puerto Rico, and the U.S. Virgin Islands are contained on one disc. Refer to the “Navigation System Map Disc” manual for a detailed explanation of map coverage and detailed city lists in each region.
Ejecting the DVD Map Disc The navigation portion of the system cannot be used if the DVD map disc is not loaded. 1. Press the MENU key to enter the Menu options, then press the MENU key repeatedly until Nav is selected or touch the Nav screen button. 2.
Map Adjustments The scale of view on the map can be adjusted. While driving, the map scrolls automatically based on the direction of travel. Map Scales 0 / 1 (Zoom In/Zoom Out): Touch the zoom in or out screen buttons or the scale on the bar to change the level of map detail.
Symbols The following symbols are the most common symbols that appear on a map screen. The vehicle is shown as this symbol. It indicates the current position and the direction the vehicle is traveling on the map. The distance to destination symbol indicates the distance to the final destination.
The distance and time to destination symbol indicates the distance and the estimated time remaining to the final destination, depending on the option selected. The straight line to distance symbol indicates the straight-line distance to the destination.
The No GPS symbol appears when the vehicle is acquiring or not receiving a Global Positioning System (GPS) satellite signal. See Global Positioning System (GPS) on page 2-38 for more information. Select the Mark screen button to store the location on the screen in your address book.
1. Select one of the POI categories to display or to delete POI icons from the map screen. Once a category has been selected the POI icon displays at the top of the screen. 2. Select up to five categories to display on the map screen. When a category is selected those POI icons display on the map.
4. Select a POI name to receive information about the POI. From this screen select: Address Book, Go, Map, or Call (if the OnStar ® account is active and if there are Hands-Free Calling minutes available). Address Book: Press to add this POI to the address book.
When you are approximately 1/4 mi (400 m) from the next maneuver in city driving, the screen displays the name and a detailed view of the next maneuver. On the freeway, these details appear at 1 mi (1200 m) from the maneuver. 3–D Lane Guidance Some major metropolitan areas may include a 3–D lane guidance feature for highway exits and junctions.
Dual Mode This dual screen symbol displays when the screen is in dual mode. Dual mode displays the route (map) on half of the screen and a maneuver or turn list on the other half. Press this button to switch between dual screen and full screen which displays the entire route.
Address Entry 2 Address Entry: Enter an address by providing the system with a city name or a street name. Enter the city name first: 1. Press the DEST hard key. 2. Select the 2 Address Entry screen button. 3. Select the state/province screen button, if the current state or province needs to change.
8. Once a street has been selected, select the House # screen button to enter the house number. The system displays the house number range that is available for the street. Select a house number. There is also a Cross Street screen option at this point.
11. Select the Start Guidance screen button. The route can now be started. See “Getting Started on Your Route” later in this section for more information. To enter a destination by entering a cross street: 1. Press the DEST hard key. 2. Select the 2 Address Entry screen button.
Point of Interest (POI) The Point of Interest (POI) destination entry method lets you select a destination from the POI list. i Point of Interest: Select this screen button to access the POI (Point of Interest) screen. From this screen you have two options to select/enter a destination: • Enter the name using the alpha keyboard.
To use the point of interest destination entry method by selecting a category: 1. Press the DEST hard key. 2. Select the i Point of Interest screen button. 3. Select the Browse POI Categories screen button to view the list of POI categories. 4. Select a category, and then a sub-category.
To use the address book entry method: 1. Press the DEST hard key. 2. Select the g Address Book screen button. A list of your address book addresses display. Use the arrows on the left side of the screen to scroll through the list. 3. Select the Go screen button next to the destination.
Using Destination Download If the map disc is not installed and the radio receives a destination download, a message displays showing that the map disc is required or it accepts the download so that it can be added to the address book.
Route Guidance Not Active If an OnStar destination is downloaded while route guidance is not active, the navigation system displays a pop-up screen and does the following screen functions: • Select Go, the navigation system starts route calculation to the destination(s) received.
Map Destination Screen Functions If the map screen is used to show destination, it has map screen capabilities such as Go, Mark, Zoom, Scroll, etc. The address is shown at the top of the screen. Getting Started on Your Route Once a destination has been entered, there are several functions that can be performed.
Turn List Turn List: Select to view the list of turn maneuvers for the entire route and to avoid turns on the route. r / q (Scroll Arrows): Select the up and down arrow to scroll through the list of maneuvers. Avoid: Select this screen button, next to the adjacent street name, to avoid the maneuver.
r / [ (Fast Forward Scroll): Select to scroll to the next stopover or to the final destination. The u button changes to a fast speed fast forward. u (Fast Forward Skip): Select to go to the next stopover or to the final destination.
To add a stopover: 1. Press the DEST hard key. 2. Select the Add or Add Stopover screen button. This button only appears if a route has been calculated. 3. Using the desired method of entering a destination, enter the stopover. See “Destination” previously for more information.
Adding Destinations to the Address Book There are two ways to add a destination to the address book: • To add the current final destination to the address book, select the Mark screen button from the map screen. The system automatically saves the final destination information in the address book.
Configure Menu Press the MENU hard key to adjust several of the system’s features and preferences. The last selected menu screen is the screen that displays; Sound, Radio, Nav (navigation), Display, or Time.
XM NavTraf fic™ (USA and Canada) Your vehicle’s navigation system may have an XM NavTraf fic receiver. XM NavTraf fic is a subscription service provided via XM™ Satellite Radio. XM NavTraf fic provides real-time traf fic information fully integrated to the navigation system to display current traf fic conditions for a driver’s chosen route.
XM NavTraf fic currently broadcasts the traf fic information for many markets nationally, and the service may be available in more cities in the future. Visit xmnavtraf fic.com for more details on local coverage. A service fee is required in order to receive the XM NavTraf fic service.
Condition Traf fic Status Icon Traf fic events are in the area, but none are on route. Traf fic events are on route. Locations and Information of Traf fic Conditions The system may take some time to sort the information. The list of traf fic conditions display in the order of distance from the vehicle, for up to approximately 150 mi (240 km).
2. Select a traf fic condition to get more detailed information of the event. Options Select the Options screen button. A Traf fic Options menu displays. Select the desired traf fic related option. Traf fic: Select to enable or disable the traf fic function.
• Yellow indicates slightly impaired traf fic flow with average speed between 25 and 45 mph. • Green indicates normal traf fic flow with average speed above 45 mph. • Orange indicates construction. Traf fic flow data arrows display on the map when scaled up to eight miles.
Name Select the Name touch screen button to display traf fic events in the order of distance. The closest event is shown first. Avoid When a route is active, the Avoid button is used to route around the listed traf fic event. After calculating a new route, the navigation system shows a new route on the full map screen.
Traf fic Event Display Categories The following are traf fic condition categories and symbols that can appear on the display: Category 1, Road Closure: q (Road Closed): Road and/or ramps closed. Category 2, Traf fic Delayed: o (Stopped Traf fic): Traf fic stopped, stop and go traf fic, delayed and congested traf fic.
Back, Map, More, and Avoid These buttons have common functions across all three Detailed Traf fic Event screens. Back: Press to return to the screen used to display the selected detailed traf fic event. Map: Press to show the related traf fic event on the map.
Display Press the MENU key to enter the menu options, then press the MENU key repeatedly until Display is selected, or select the Display screen button. Display Of f Select this button to turn the display of f. Press the Nav, Dest, Fav, or Menu hard key or the f (tone) button to view the display.
Auto (Automatic): Select this screen button so the system can automatically adjust the screen background depending on exterior lighting conditions. Night: Select to make the map background darker.
Global Positioning System (GPS) The navigation system determines the position of the vehicle by using satellite signals, various vehicle signals, and map data.
Vehicle Positioning At times, the position of the vehicle on the map may be inaccurate due to one or more of the following reasons: • The road system has changed. • The vehicle is driving on slippery road surfaces such as in sand, gravel, and/or snow.
Problems with Route Guidance Inappropriate route guidance could occur under one or more of the following conditions: • You have not turned onto the road indicated. • Route guidance may not be available when using automatic rerouting for the next right or left turn.
Ordering Map DVDs The map DVD in the vehicle is the most up-to-date information available when the vehicle was produced. The map DVD is updated periodically, provided that the map information has changed.
✍ NOTES 2-42.
Navigation Audio System ................................. .3-2 CD Player .................................................. .3-10 DVD Player ................................................ .3-16 Care of Your CDs and DVDs ........................ .3-21 Auxiliary Devices .
Navigation Audio System Notice: Before adding any sound equipment to the vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer/ retailer. Also, check federal rules covering mobile radio and telephone units.
Finding a Station There are three ways to find/change stations: • If viewing a full map screen, use the ¨© SEEK keys and f knob. Preset stations cannot be changed from the full map screen. • If viewing a full map screen, select the source screen (AM, FM, XM, CD, etc.
Category: 1. Select the screen button, located in the middle of the screen, to receive a list of all of the selected band stations in the area. 2. Use the up and down arrow screen buttons to scroll the frequencies. 3. Select the desired frequency. XM lists also contain a category to select and the stations or channels that pertain to the category.
Storing Radio Station Presets This feature allows up to 30 preset stations to be stored. You can mix AM, FM, and XM (if equipped). To store presets: 1. Press O to turn the system on. 2. If viewing a map screen, select the source screen button, press the AUDIO key, or press the FAV (favorite) key.
Setting the Tone TREBLE: Select and hold the plus (+) or minus ( − ) sign to increase or decrease the treble. If a station is weak or noisy, decrease the treble. MID (Midrange): Select and hold the plus (+) or minus ( − ) sign to increase or decrease the midrange.
Radio Menu Press the MENU key to enter the configure menu screen, then press it repeatedly until Radio is selected, or select the Radio screen button to make changes for radio information displayed, number of preset pages, XM categories, if equipped, and automatic volume control.
Automatic Volume Control Automatic Volume Control: With automatic volume control, the audio system adjusts automatically to make up for road and wind noise while driving.
Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information.
CD Player The player can be used for CDs with conventional CD audio, MP3, or WMA compressed files and may have the capability to play DVD audio and DVD video. See DVD Player on page 3-16 for more information about DVD audio and video. With the ignition on, insert a CD partway into the slot, label side up.
r (Rewind): 1. Select and hold to rewind quickly through a track selection. Sound is heard at a muted or a reduced volume. 2. Release this button to stop rewinding. The display shows the elapsed time of the track. [ (Forward): 1. Select and hold to fast forward quickly through a track selection.
• Create a folder structure that makes it easy to find songs while driving. Organize songs by albums using one folder for each album. • All playlist files (.m3u or .pls) must be removed from disc contents. Playlists are not supported. • It is recommended that there is a maximum of 192 files on a CD-R(W) disc.
Order of Play Tracks are played in the following order: • The radio does not support playlist files. • Order of play dif fers depending if the compressed audio disc is fully scanned or unscanned. See “Scanning Compressed Audio Disc” previously in this section.
j / r (Pause/Play): 1. Select to pause the CD. This button then changes to the play button. 2. Select the play button to play the CD. Random: 1. Select to hear the tracks in random, rather than sequential, order. 2. Select Random again to turn of f random play.
¨ SEEK / © SEEK: 1. Press the up arrow to go to the next track. 2. Press the down arrow to go to the start of the current track, if more than eight seconds have played. 3. If either arrow is pressed more than once, the player continues moving backward or forward through the CD.
DVD Player The player can be used for DVD audio and DVD video. With this feature, movies/pictures do not appear on the navigation screen, unless the vehicle is in P (Park). It operates on the Rear Seat Entertainment (RSE) screen while the vehicle is moving.
Playing a DVD There are three ways to play a DVD: • Once a DVD is inserted, the system automatically starts play of the DVD up to the DVD top menu. The r (play) button must be pressed to start the movie from the DVD’s menu screen. • If you are on a map screen, select the DVD screen button.
j / r (Pause/Play): 1. Select to pause the DVD. This button then changes to the play button. 2. Select the play button to play the DVD. 3. Select this button in a DVD disc main menu to start the DVD. c (Stop): 1. Select to stop play of the DVD. 2. Select the play button to continue playing the DVD from where the DVD was stopped.
Audio: 1. Select to display the audio options. 2. Select the audio options that best improve sound quality. This is not available on all DVDs or when the DVD is stopped. This button may not be available for some DVD audio discs. Acadia only, see “Fading With a Bose ® Surround Sound System” later in this section.
Select J to fill the screen on the left and right sides. Select d to fill the screen on the top and bottom. SEEK ¨ (Next Track/Chapter): Press this hard key to go to the next track or chapter if the time elapsed is greater than 10 seconds. This button may not work when the DVD is playing the copyright information or the previews.
DVD Messages If Disc Read Error appears on the display and/or the DVD comes out, it could be for one of the following reasons: • A disc was inserted with an invalid or unknown format. • The disc is not from a correct region. • The map DVD disc was installed into the DVD audio/video slot.
Auxiliary Devices The vehicle may have a Rear Entertainment System (RSE). The RSE has audio adapters that lets you connect auxiliary devices. The audio can be heard through the speakers or through the wireless or wired headphones.
Voice Recognition ........................................... .4-2 Section 4 Voice Recognition 4-1.
Voice Recognition The navigation system’s voice recognition allows for hands-free operation of navigation and audio system features. Voice recognition can be used when the ignition is on or in ACC/ACCESSORY or when Retained Accessory Power (RAP) is active.
Voice Tag Commands The following are voice tag commands that can be accessed by clearly stating the commands exactly as they are written. There can be up to 40 voice tag entries for destinations. Navigation go to [destination], navigation select: These commands instruct the system to select a destination saved under the stored voice tag.
Radio [select] (channel) XM, radio [select] (channel) satellite: Instructs the system to go to a specific channel on the XM™ band (if equipped). Radio help: This command instructs the system to assist with radio commands.
A Adding Destinations to the Address Book ........... 2-26 Adding or Changing Preset Destinations ............. 2-26 Alpha-Numeric Keyboard ................................... 2 - 3 Audio System Radio ..................................................
F Fading With a Bose ® Surround Sound System (Acadia and Enclave Only) ............................ 3-20 Finding a Station .............................................. 3 - 3 G Getting Started, Navigation ................................ 1 - 4 Getting Started on Y our Route .
O OnStar ® Destination Download .......................... 2-19 Ordering M a p D V D s ................................................. 2-41 Overview , Navigation System ............................. 1 - 2 Owners, Canadian ..........................
T T ouch-Sensitive Screen Buttons .......................... 2 - 3 T raffic Options ................................................ 2-27 U Using a Compressed Audio CD/DVD ................. 3-11 Using Destination Download .............................
デバイスGMC Acadia 15919282の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
GMC Acadia 15919282をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGMC Acadia 15919282の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GMC Acadia 15919282の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GMC Acadia 15919282で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GMC Acadia 15919282を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGMC Acadia 15919282の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GMC Acadia 15919282に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGMC Acadia 15919282デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
