A.O. Smithメーカー186965-001の使用説明書/サービス説明書
ページ先へ移動 of 40
PRINTED 0209 186965-001 Design information for single and multiple unit installations for residential, commercial, recircula- tion and storage tank systems.
2 Certifications .................................................................................. 3 Water Quality and Scale ................................................................ 8 Pump Sizing for Circulation ..............................
3 Certified to applicable U.S. standards for appliances using gas or other petroleum fuel. Certified to applicable Canadian standards for appliances using gas or other petroleum fuel. Certified by the Uniform Plumbing Code (UPC) Certified by National Sanitation Foundation (NSF), www.
Consumer Information The on-demand water heaters must be installed according to all local and state codes or, in the absence of local and state codes, the “National Fuel Gas Code”, ANSI Z223.
In addition to using the lowest possible temperature setting that satisfies your hot water needs, a means such as a mixing valve, should be used at hot water taps used by these people or at the water heater. Mixing valves are available at plumbing supply or hardware stores.
Closed System/Thermal Expansion CAUTION - PROPERTY DAMAGE HAZARD As water is heated, it expands (thermal expan- sion). In a closed system, the volume of water will grow. As the volume of water grows, there will be a corresponding increase in water pres- sure due to thermal expansion.
Temperature and Pressure Relief Valve For protection against excessive pressures and temperatures, a temperature and pressure relief valve must be installed in the opening on the on-demand storage tank.
8 W a ter Quality and Scale A complete water analysis and an unde rstandi ng of system requirements are needed to protect the on-demand water heaters and water heating systems from scale. Water analysis shows whether water is hard or soft. Hard water, unless treated, will cause scaling or liming of the heat exchanger.
9 Pump Sizing for Circulation 1. Use the chart below or one appropriate for your con ditions to determine the heat loss in the length of the hot water supply and return piping. For example, 100 ft of 1-1/2 in bare copper tubing results in a heat loss of 5300 Btu/h.
10 T ank W a ter Heaters in a Circulation Loop The following applies when using a tank water heater (gas or electric) to provide heat for a circulation loop. Drawing H-1-RP is an example. The heat output of the tank must be equal to or greater t han the calculated circulation loop heat loss.
The following applies when using on-demand water heaters to recover a storage tank. Drawing H-1-TC is an example. On-Demand water heaters have a pressure loss which must be considered in the system design. Reference the pressure loss curve for the heater m odel being used to determine the pump size for the desired recovery rate.
12 Pressure Loss (psi) Water Flow (gpm) 0. 0 5. 0 10. 0 15. 0 20. 0 25. 0 30. 0 35. 0 40. 0 45. 0 01 234 56 789 1 0 1 1 0. 0 10. 0 20. 0 30. 0 40. 0 50.
13 Pressure Loss (psi) Water Flow (gpm) Pressure Loss (ft head) Figure “5” 0 5 10 15 20 25 30 35 40 45 0123456789 1 0 1 1 0 10 20 30 40 50 60 70 80 90 100 705 505 305 Pressure Loss Curves 200/201 .
Domestic Hot W ater - S tandard Installation 1 On-Demand W ater Heater Preferred Piping Installation Drawing Number: Drawing Date: H-1 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 2 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-2 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 3 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-3 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 4 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-4 September 07, 2008 Pr i ma ry Hot W ater Supply Line Cold W ater.
Domestic Hot W ater - S tandard Installation 5 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-5 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Domestic Hot W ater - S tandard Installation 6 On-Demand W ater Heaters Preferred Piping Installation Drawing Number: Drawing Date: H-6 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing.
Drawing Number: Drawing Date: H-1-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-E September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-RO September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-RO September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-RP September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-1-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-2-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-3-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-T September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: H-6-TC September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
Drawing Number: Drawing Date: MP-01 September 07, 2008 NOTE: This drawing is not intended to describe a complete system and is not a replacement for a pro- fessional engineering drawing. It is intended only as a guide and does not imply compliance with local building code requirements.
39 Notes.
• 500 T ennessee Waltz Parkway • Ashland, TN 37015 •.
デバイスA.O. Smith 186965-001の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
A.O. Smith 186965-001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはA.O. Smith 186965-001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。A.O. Smith 186965-001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。A.O. Smith 186965-001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
A.O. Smith 186965-001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はA.O. Smith 186965-001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、A.O. Smith 186965-001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちA.O. Smith 186965-001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。