GodexメーカーEZPi-1300の使用説明書/サービス説明書
ページ先へ移動 of 45
User’s Manual EZPi-1000 Series P/N. 920-013011-01 Rev. A, 08.2009.
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comp ly with the limits for a CLASS A digital devic e, pursuant to Part 15 of the FCC Rules. Th ese limits are designed to provide rea sonable protection against harmful interference when the equipm ent is operated in a commercial environment.
Safety Instructions Bitte die Sicherheitshinweise sorgfältig lese n und für später aufheben. 1. Die Geräte nicht der Feuch tigkeit aussetzen. 2. Bevor Sie die Geräte ans Stromnet z ansc hließen, verge wissern Sie Sich, dass die Spannung des Geräts mit der Netzspan nung übereinstimmt.
Safety Instructions Please read the following instruction s seriously. 1. Keep the equipment away from humidity. 2. Before you connect the equipment to the power outlet, please check the voltage of the power source. 3. Disconnect the equipment from the volta ge of the power source to p revent possible transient over voltage damage.
1. BARCODE PRINTER ................................................................... 5 1-1. Printer Accessories ......................................................................................................... 5 1-2. General Specifications .
1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the acce ssorie s that come with the packag e, and store appropriately. Barcode printer Power cord Switching Power.
Code Pages CODEPAGE 437, 850, 851, 852, 855, 857, 860, 861, 862, 863, 865, 866, 869, 737 WINDOWS 1250, 1251, 1252, 1253, 125 4, 1255 Unicode (UTF8, UTF16) Graphics Resident graphic file types are BM P.
1-3. Communication Interface Parallel Interface Handshake : DSTB conne cts to the printer, BUSY conne cts to the host Interface cable : Parallel cable compatible to IBM PC Pin out : See below PIN NO.
Internal Interface UART1 wafer Ethernet module N.C 1 1 N.C TXD 2 2 RXD RXD 3 3 TXD CTS 4 4 RTS GND 5 5 GND RTS 6 6 CTS E_MD 7 7 E_MD RTS 8 8 CTS E_RST 9 9 E_RST +5V 10 1 0 +5V GND 11 1 1 GND +5V 12 1 .
1-4. Printer Parts 1. Cover Open Button 2. Top Cover 3. Label Roll Core 4. Ribbon Rewind Wh eel 5. LCD Module Case 6. Printing Mechanism 7. Front Cover Piece 1. Ribbon Rewind Shaft + Empty Ribbon Roll 2. Locking Tenon (left/right) 3. CF Card Slot Cover 4.
1. Ribbon Supply Shaft 2. Label Guide 3. Platen Roller 4. Print Line Adjustment Gear 5. Label Sensor 1. LCD Control Panel 2. Fan-Fold Label Insert 3. Connection Port for PS2 / Wireless LAN Antenna (O ptional) 4. Power Switch 5. Ethernet Port 6. USB Port 7.
2. Printer Installation This printer model has the following pri nt modes: Thermal Transfer (TT) When printing, ribbon must be installed to transfer the print co ntents onto the media. Direct Thermal (DT) When printing, no ribbon is necessary; it only requires direct therm al media.
4. Feed the ribbon from the Ribbon Supply Shaft under the Print Head. 5. Wrap the ribbon around the Ribbon Shaft and stick the ribbon onto the Empty Ribbon Roll Core.
2-2. Label Installation 1. Open the top cover by pressing the Cover Open Buttons on both sides. 2. Insert the Label Roll Core into the label roll. 3. Assemble the Label Stop Plates on both sides of label roll. 4. Place the label roll into the printer.
2-3. Label Roll Core Installation Instruction (A) 1” roll core installation (B) 1.5” roll core installation (C) 3” roll core installation EZPi-1000 User’s Manual 14.
2-4. Card / Hang tags Installation When installing cord tags, the tag hole must align with the sensor arrow (as indicated in figure ), then use the Label Guide to secure the tags. Sensor Detection Position Sensor 2-5. PC Connection 1. Please make sure the printer is powered off.
2-6. Driver Installation 1. Insert product CD to your computer’s CD Drive and find the "Windows Drives" folder. 2. Select the icon of driver file and click it to start the installation. 3. Follow the instruction on screen to keep the installation going.
6. Select connection port. 7. Enter the printer name and set printer sharing option. 8. A description page of printer settings will be displayed after all settings are completed. 9. Check if all printer settings are correct and then press Finish to start copying driver files.
3. Control Panel 3-1. Control Panel Introduction Control keys FEED PAUSE CANCEL LED indicators Power (Ready) The Power (Ready) light is to indicate the power on status and the printer is ready to print. Ribbon Ribbon status indication Media Media status indication 3-2.
With different combinations of FEED PAUSE and CANCEL keys, the printer ca n perform various functions as follows: Item Key Beep LCD Message Description Self test + Power on 3 beeps Self test Press and hold key and turn on the printer until the buzzer beeps 3 times.
3-3. Setting mode In the Setting Mode, changes can be made acco rdin g to requirement on the printing mode, options, media type, and parallel interface (printer ca n only go into setting when connected to PC by parallel cable, USB cable, or serial ca ble).
Below are general descriptions of setting items. Darkness Default: 15 Set the darkness of printing result. The setting value is from 0 to 19 and the default value is 15. Speed Set the speed of printing. Adjust Stop Position Default: 0 Set the stop position of printing.
Code Page Default: Code Page 850 Code Pag e850 Code Pag e852 Code Pag e437 Code Pag e860 Code Pag e863 Code Pag e865 Code Pag e857 Code Pag e861 Code Pag e862 Code Pag e855 Code Pag e866 Code Pag e737.
The diagram of Setting Mode To enter the Setting mode, please press and hol d the Pause key about 3 to 4 seconds until the buzzer beeps 3 times and LCD sho ws "Setting mode".
3-4. Self-Test The Self-Test function will help user to check whether the printer i s operating normally. The printer will go back to standby mode after prin ting a Self-Te st page. Below are the Self-Test procedures: 1. Power off the printer, press and hold the FEED key.
3-5. Dump Mode When the print result doesn’t match the label setting, it’s re commended to go into the Dump Mode to check whether there is a mistake in dat a tran smission between the printer and the P C.
3-7. Keyboard Mode EZPi-1000 series printer can sup port keyboard with PS2 interface. To connect the PS2 keyboard, please do as follows: 1. Please be sure the printer power is on and is showing no error message. 2. Power off the printer and then plug the PS2 ke yboard con nector into the socket in the back of printer.
6. LCD will show the Serial Number Prompt. 7. Key in the start value. (Example:00001) 8. LCD will show the first Variable Prompt. 9. Key in the variable data. (Example: Apple) 10. LCD will show t he second Variable Prompt. 11. Key in the variable data.
14. The printer will print out 3 labels that include user-defined variables a nd serial number. EZPi-1000 User’s Manual 28.
3-8. Error Messages If problems occur that prevent the printer printing normally, the printer will beep as warning, and error messages will be displayed.
Memory Full 2 beeps twice Memory is full Delete unnecessary data in the memory or use CF Card. Filename can not be found 2 beeps twice Can’t find the file Use “~X4” command to print out all the files, then check whether the file exist and the names are correct.
4. Accessory 4-1. Stripper Installation 1 Stripper Module 2 Screw (TAP 3*8) x 2pcs 【 Note1 】 Please power off the printer before installing the stripper module. 【 Note2 】 Label liner thickness is recommended to be 0.0 6mm ± 10% with basic weight 65g/ ㎡ ± 6%.
5. Plug in the stripper connector onto the switchboard socket. (refer to right figure) 【 Note 】 There are 2 sockets on the converting boards (one is f or stripper installation, and another one is for cutter), before plug the connector i nto socket, please check the pin first.
10. Follow the direction as shown in figure to feed the liner across the stripper. 11. Close the upper print mechanism and the stripper. 12. Press the FEED key to adjust the position of label and complete the installation.
4-2. Cutter Installation 1 Cutter Modul e 2 Screw (TAP 3*8) x 2pcs 2 1 【 Note1 】 Please power off the printer before installing the cutter module. 【 Note2 】 Do not cut self-adhesive labels! Th.
6. Place the left side of the stripper first, and then fit the right side. 7. Flip the cutter module downward to open the cutter. 8. Hold the cutter module and lock it with screws 9. After the screws are locked, flip to close the cutter module. 10. Feed the label through the Label Guides.
4-3. WLAN Module Installation 1 Ethernet Cable 1.8M 2 Secure Screw*1 3 Bracket Screw*2 4 Module Bracket 5 WLAN m odule 6 Module Connection Wire 7 WLAN Antenna 8 Nut (for Antenna) 9 Washer (for Antenna) 10 Fixture Plate 11 Antenna Bracket 1. Make sure the power is off and the power cable is unplugged.
6. Unscrew the Ethernet Module Secure Screw. 7. Remove the Ethernet Module and its connection wire. 8. Unscrew the screw of PS2 Port with long-nose pliers 9. Unscrew the Ground Wire Screw and unplug the connection wire of PS2 Port to remove the PS2 Port.
13. Align the WLAN module to the Ethernet port and plug into it. 14. Secure the module onto the back plate. 15. Thread the Module Connection Wire through the other con nection wires on the mainboard as the direction showed in figure. Then arrange the Antenna Connection Wire as the arrow sho wed.
17. Put the Fixture Plate first then the Washer and tighten the Nut to mount Antenna Connection Wire o n the printer. 【 Note 】 It is suggested to tighten the Nut with long-nose pliers when m ounting the Antenna Connection Wire. 18. Turn the Antenna according to the direction as arrow sho wed to mount it on the Antenna Connection Wire.
4-4. CF Card Adapter Installation 1 CF Card Adapter (Front) 2 CF Card Adapter (Back) 【 Note 】 Please power off the printer before installing the CF Card Adapter. 2 1 1. Open the top cover by pressing the Cover Open Buttons on both sides. 2. Take off the label roll core.
4-5. CF Card Instruction EZPi-1000 series printers can read the CF Card after installed the CF Card Adapter. If the built-in memory is insufficient for storing label format s, graphics or fonts, users can us e CF Card as external memory to provide more memory space.
5. Maintenance and Adjustment 5-1. Thermal Print Head Cleaning Unclear printouts may be cau sed by dusty print head, ribbon stain or label liner glue. Therefore when printing, it’s necessary to keep the top cover closed. Also, check and prevent paper/lab el from being stained or dusty to ensure print quality and to prolong the print head life.
5-3. Print Line Adjustment To get better printing balance and quality, use print head adjusting gear to adjust the contacting surface between print head and label. 1. When turning print head adjusting gear counter-cl ockwise (as arrow 1 shows), print head would move in the direction where arrow A shows.
5-5. Troubleshooting Problem Recommended Solution Power on the printer, but the LED does not light up ♦ Check the power con nector is plugged correctly LED light turns red (power/status) after print.
デバイスGodex EZPi-1300の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Godex EZPi-1300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGodex EZPi-1300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Godex EZPi-1300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Godex EZPi-1300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Godex EZPi-1300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGodex EZPi-1300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Godex EZPi-1300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGodex EZPi-1300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
