Gracoメーカー240-362の使用説明書/サービス説明書
ページ先へ移動 of 18
308–845 Re v . C First choice when quality counts. t 8119A This gun and hose for Delta Spray Air Spray package or Delta Spray HVLP package This gun and hose for PRO 3500sc Electrostatic package INSTRUCTIONS–P ARTS LIST INSTRUCTIONS This manual contains important warnings and information.
1A 308845 Instruction Manual – Parts List Changes This page contains a summary of changes or additions that do not appear in the contents of the manual. Improve pressure control instructions (Graco Ref. 6557). Change 30psi HVLP fluid regulator and gauge to a 60psi gauge and regulator.
1B 308845 Notes.
308-845 2 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation 6 . . . . . . . . . . . . . . . . . . . . . . . . . . .
308-845 3 W ARNING INSTRUCTIONS EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in a serious injury . D This equipment is for professional use only . D Read all the instruction manuals, tags, and labels before operating the equipment.
308-845 4 Setup CAUTION This equipment is compatible with most water-based materials. See the wetted parts in the T echnical Data section and your fluid and solvent manufacturer ’ s compatibility information. Do not use acid catalyzed materials; they are incom - patible with the acetal used in this pump.
308-845 5 Setup Assembling the W all-Mount Unit See Fig. 1 Install the wall bracket (G) 5 ft (1.5 m) above the floor . For proper hole dimensions, use the W all Mounting Hole Layout on page 15. Be sure the wall is strong enough to support the weight of the pump and hoses, any accessories, the fluid, and stress caused by pump operation.
308-845 6 Operation Using the Gun See the gun instruction manual for gun operation, care, flushing, cleaning, and technical data. Read the entire gun manual before operating the sprayer . Pressure Relief Procedure See Fig. 1 The system remains pressurized until pressure is manually relieved.
308-845 7 Operation Priming the System See Fig. 1 1. Close the gun air regulator (F). 2. If your system has a fluid pressure regulator (G), close it. 3. Open the bleed-type master air valve (K). 4. Slowly set the pump air regulator (E) pressure to 20 to 30 psi (140 to 210 kPa, 1.
308-845 8 Operation When to Shut Down the System Shut down the system at the end of the work shift and before checking, adjusting, cleaning, or repairing the system. Always relieve the pressure . W ARNING T o reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 6.
308-845 9 Maintenance See the separate component instruction manuals for individual component maintenance procedures. Access to some system components requires that you remove the shields. The following steps are for shield removal. Shield replacement is the reverse of these steps, so make sure you take notes on the proper hose connections.
308-845 10 Parts List W all-Mount Packages with Fluid Pressure Regulators Model No. 240–349 , Delta Spray air spray package Model No. 240–350 , Delta Spray HVLP package Model No. 240–351 , no hoses (31) or gun (30) Model No. 240–352 , PRO 3500sc electrostatic package Model No.
308-845 11 Parts Drawing 13 20 Grounding Detail 19 26 37 8088A 1 8 2 3 5 6 24 24 9 9 10 16 16 17 21 25 29 34 30 31 31 32 33 38 39 40 50 28 7 30 222–300 shown 12 27 27 15 15 W all-Mount Packages with Fluid Pressure Regulators Model No. 240–349 , Delta Spray air spray package Model No.
308-845 12 Parts List W all-Mount Packages with Surge T anks Model No. 240–361 , Delta Spray air spray package Model No. 240–362 , Delta Spray HVLP package Model No. 240–363 , no hoses (31) or gun (30) Ref. No. Part No. Description Qty . 1 240–210 SHIELD ASSY , front Contains 1a to 1h, shown in Fig.
308-845 13 Parts Drawing Grounding Detail 26 37 8089A 20 19 13 1 8 5 6 24 24 9 9 10 16 17 21 25 29 34 30 32 33 40 50 12 27 27 15 15 38 16 3 7 40 W all-Mount Packages with Surge T anks Model No. 240–361 , Delta Spray air spray package Model No. 240–362 , Delta Spray HVLP package Model No.
308-845 14 Accessory Fluid Filter Kit Fluid Filter Kit 240–440 Ref. No. Part No. Description Qty . 101 1 14–361 FIL TER, fluid 1 102 1 13–322 CONNECT OR, male 1 103 054–188 TUBE; PTFE; R 3/8” O.
308-845 15 T echnical Data Category Data Maximum fluid working pressure 100 psi (0.7 MPa, 7 bar) Maximum incoming air pressure 100 psi (0.7 MPa, 7 bar) Maximum operating temperature 120 _ F (49 _ C) Gun See separate gun instruction manual. Pump See separate pump instruction manual.
308845 16 Graco Standard W arranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use.
デバイスGraco 240-362の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 240-362をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 240-362の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 240-362の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 240-362で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 240-362を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 240-362の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 240-362に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 240-362デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。