Gracoメーカー311304Jの使用説明書/サービス説明書
ページ先へ移動 of 16
311304J Instructions - Parts List GTP10 Pump For pumping gasoline, diesel fu el, and kerosene. Do not use to pump other fluids including water. Models 260000 through 260017, 260019, 260024, 260580, an.
Models 2 311304J Models Part No. Hose Nozzle 12 VDC, 10 gpm (38 lpm), 12.5 amps 260000 260069 - 12 ft (3.66 m) grounded 260079 - manual, leaded/die sel 260001 260069 - 12 ft (3.66 m) grounded 260082 - automatic, regula r/diesel 260002 260069 - 12 ft (3.
Models 311304J 3.
Warnings 4 311304J Warnings The following general warn ings are for the setup, use, ground ing, maintenance, and repair of this equipme nt. Addi- tional, more specific warnings may be found th ro ughout the body of this manual where applicable. Symbols appea r- ing in the body of the manual re fer to these general warnin gs.
Warnings 311304J 5 EQUIPMENT MISUSE HAZARD Misuse can cause de ath or serious injury. • Do not operate the unit when fatigued or under the influen ce of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component.
Installation 6 311304J Installation When unpacking pump, check for shipp ing damage. Report any shipping damage to delivering carrier imme- diately. Mounting Pump 1. Apply PTFE thread tape (provided with the pump) to large thread of bu ng adapter (9) (2 in.
Installation 311304J 7 3. Cut the suction tube so that it is 2 in. (55 mm) from the bottom of the tank when installed in the tank. 4. Insert ga sket (7f) into union nut (1k). If using Grac o supplied PVC suction tube it is not necess ary to apply thread tape before assembly, just scre w into pump inlet (1j).
Installation 8 311304J Electrical Installation 12 VDC and 24 VDC To install wiring for a ne gative grou nd system : 1. Ensure pump switch is OFF. 2. To remove electrical cover (2a) , remove four bolts (2c). 3. Strip 3 in. (76 mm ) of outside insu lation from power cable (6c) from e nd opposite of fuse.
Operation 311304J 9 Priming Pump All pump models should prime with in 5 seconds after pump is turned on up to a height of 36 in. (9 1 mm). Pumps installed at height up to 5 ft. (1.52 m) may have difficulty priming. Follow pr ocedure below to initiate prime.
Troubleshooting 10 311304J Troubleshooting Problem Cause Solution Motor runs but pump will not prime. Motor rotation wrong. (12 VDC and 24 VDC units only.) Check wiring in structions for possible problems. Missing relief valve o-ri ng seal (4c/7a). Remove gear cover (1b) inspect seal (4c/7a), replace if missing or damaged.
Troubleshooti ng 311304J 11 Motor stalls when nozzle is clos ed. Bypass relief valve (4a) stuck. Inspect relief valve, making sure poppet is free. Replace if damaged. Low supply voltage. Check supply voltage. Gears (1c/10a) dam aged and binding. Inspect gears.
Parts Drawing 12 311304J Parts Drawing 3a 3c 3d/7e 1a 8e 8b 8f 8g 1h 1e/7b/10c 1f/7c/10b 2e 2f 3b 1b 1c/ 10a 1d 4b 4a 2h 2i 8c 8a 8d 4c/ 9 7f 1k 1g/7d 2g 2c 2b 2d 5c 5a 2a 2c 6b 6c 6a Models 260000 th.
Parts Li st 311304J 13 Parts List Models 260000 through 260017, 260019, 260024, 260580, and 260581, 12 VDC Models 260020 and 260021, 24 VDC Models 260022 and 260023, 230 VAC Models 260025 through 260028, 115 VAC Ref.
Parts List (continued) 14 311304J Parts List (continued) Models 260000 through 260017, 260019, and 260024, 12 VDC Models 260020 and 260021, 24 VDC Models 260022 and 260023, 230 VAC Models 260025 through 260028, 115 VAC Replacement Danger an d Warning labels, tags, and cards are available at no cost.
Technical Data 311304J 15 Technical Data Valox ® is a register ed trademar k of the General Elect ric Company Performance Chart Working pressure 10 psi (0.07 MPa, 0.7 bar) Inlet size 1 in. npt Outlet siz e 3/4 in. npt Weight 20 lb (9 kg) Power cable 18 ft (5.
All written and visual data contained in this document reflects the latest product info r mation available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 311304 Graco Headquarters: Minne apolis International Offices: Belgium, China, Japan, Korea GRACO INC.
デバイスGraco 311304Jの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 311304Jをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 311304Jの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 311304Jの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 311304Jで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 311304Jを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 311304Jの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 311304Jに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 311304Jデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。