Gracoメーカー312964Cの使用説明書/サービス説明書
ページ先へ移動 of 20
The Matr ix Tank Lev el Monitor co ntains an R F device w ith the fo llowing appro vals: FCC ID: TFB-FREEST AR IC: 5969A-FREEST AR Industry Canada Statement The term “IC” before t he certification/reg istra- tion number only signifies tha t the Industr y Canada technical specifications were met.
Warnings 2 312964C Wa r n i n g s The f ollowing warnings are f or the setup , use, groundin g, maintenance, and repair of this equ ipment. The exclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedure -specific risk.
Set Up 312964C 3 Set Up Dips witch Settings The TLM has two , 4 - position dips witches labeled S1 and S2. TLM dips witches must be set to match those of the transceiver the TLM will be communicating with. The f actor y default setting for all TL M’ s is (‘1’ ‘1’).
Set Up 4 312964C 7. Install tw o, 9-v olt alkaline batteries (1). Be sure that the batter ies fully engage the mounting clips by pushing on the botto m of each battery with your thumb . 8. Replace insulating f oam (4). 9. Replace co ver (7) and secure it with the f our screws (3).
Set Up 312964C 5 Dipswitc h Setting for Netw ork ID and T ransceiver ID See F IG . 3 f or dips witch setting configur ations. b The batteries must be di sconnected and remov ed before changi ng dips witch settings or the TLM will not be able to communic ate with the PC software.
Set Up 6 312964C Registering the TLM Graco recommend s registering TLM prior to installa- tion. The TLM operating pa rameters are cont rolled by the Matrix PC Software and setup by the System Adminis- trator . See the Matrix 3 Software instruction manual f or the PC setup instructions.
TLM Display 312964C 7 TLM Displa y (See F IG . 6, page 8) TLM ID - Unique number assign ed to the TLM to distin- guish it from oth er TLM’ s in the syst em. Batter y Life - Remaining lif e of the unit’ s batter ies. Sys- tem Administrator on Matr ix PC Software d eter mines when Low Batter y W ar n ing message is ge nerated.
TLM Registration Process 8 312964C TLM Registration Pr ocess F IG . 5 Press & Hold DISPLA Y button Battery NW ID TX ID REGISTER MODE Ack received from T ransceiver No Ack received from T ransceiver TLM ID TLM ID TLM ID BLANK BLANK VERSION xx.xx.xx VERSION xx.
Installation 312964C 9 Installation 1. Remo ve the b ung fitting and scre w in the TLM hand-tight. DO NOT use a wrench to tighte n as this ma y damage the TLM. Do not use thre ad lock adhe- siv e as this may d amage the TLM. 2. The TLM m ust be mounted with in 2 degrees from per pendicu lar to the surface of the fluid.
Viewing Data 10 312964C Vie wing Data Press and release th e Display b utton (A). Data appears on displa y (B); each screen lasting a f ew seconds bef ore going on to the next.
Troubleshooting 312964C 11 T r oubleshooting Prob lem Cause Solution Brand new monitor’ s dis- pla y is very dim. Unit is shipped with protective coat- ing o ver displa y . Remo ve protecti ve coating. Monitor displays “In valid Reading”. The TLM reading is outside of the programmed size parameters.
Troubleshooting 12 312964C Monitor readings are inaccurate. T a nk geometr y incorrectly defi ned. See T ank Lev el Monitor Software Guide or PC Software Guide fo r d e t a i l s . T a nk Lev el Monitor has not be en updated with latest adjustments made within The profile ID on the PC .
Service 312964C 13 Service Once the T ank Lev el Monitor has been in stalled, no additional maintenance or ser vice is necessar y , with the excep- tion of replac ing batteries. Replacing Batteries Alwa ys repl ace bot h batteries with two new 9- volt alkaline batte r ies whene ver y ou change batteries in the TLM.
Parts 14 312964C Pa r t s 3 2 1 1 Remov e protective cov er used for shipping before programming. Do not remov e. This is required to mainta in intrinsic safety approv al.
Technical Data 312964C 15 Te c h n i c a l D a t a NO TE: FCC, C-Tic k and IC approvals are f or the RF device contained in the Matrix T ank Lev el Monitor (TLM). Ultrasonic T ank Depth Measurement rang e 0 - 30 ft. (0 - 9 m) Not f or use in pressurized t anks.
Dimensions 16 312964C Dimensions A 9.1 in (231 mm) B 4.9 in. (124 mm) 1-1/2 in. npt A B 2 in. npt ti12031a.
Tank Geom etry 312964C 17 Ta n k G e o m e t r y V ertical T ank: • Maximum V olume = 999, 999 gallons or liters . • T ank walls must be uniformly ve r tical from empty lev el to full F IG .
Tank Geomet ry 18 312964C Cylindrical T ank: • Maximum V olume = 999, 999 gallons or liters . • T ank end walls m ust be flat; th ey cannot be any other shape , including belled. F IG . 11 ti12695a Maximum Length Maximum Height 30 ft. (360 in) 30 ft.
Tank Geom etry 312964C 19 Obround T ank: • Maximum V olume = 999, 999 gallons or liters . • T ank end walls m ust be flat; the y cannot be any other shape inclu ding belled. F IG . 12 ti12694a Maximum Width 30 ft. (360 in .) Maximum Length Maximum Height 30 ft.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents.
デバイスGraco 312964Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Graco 312964Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco 312964Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco 312964Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco 312964Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco 312964Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco 312964Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco 312964Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco 312964Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。