Graco Inc.メーカー800-233の使用説明書/サービス説明書
ページ先へ移動 of 16
.. . This manual contains IPAPQRTANT WARNINGS and 1NSTRUCTIONS READ AND RETAIN FOR REFERENCE er PIN 800-233 SERIES "A" 1200 psi (82 bar) OPERATING PRESSURE GWACQ BNC.
Gesaeual Safety This pressure washer generates very high fluid pressure. Spray from the gun. leaks or ruptured components can inject fluid through your skin and into your body and cause extremely serious bodily injury, including the need for amputation.
~~~~~~~~~~n~~$~ HAZARD eapleoai Safeuy ,. Any misuse of the pressure washer or accessories, such as overpressurizing, modifying parts, using damaged parts, can cause them to rupture and result incompatible chemicals and fluids, or using worn or in fluid injection, splashing in the eyesor ontheskin, or other serious bodily injury or property damage.
1. Remove the two hood bolts, flats and locks, from the hood open. the center bottom of each side of the hood. Pivot 2. Position the handle into the end of the chassis closest to the wheels. Line up the four mounting outside of the chassis. Use flat washers only on holes.
Water Supply CAUTION pump, check your local plumbing code Before connecting the water supply to the regarding cross-connection to thewater supply. A backflow preventor. Part No. 801-133, is contaminated water intothefreshwatersupply. available to prevent the back flow of Install upstream from the pump.
Chemical Injector Operation 8. Be sure that the control ring on the injector is open two full turns from the closed position. To check this, the hood must be opened. Once the control ring is open, it may be left alone. The chemical mixture is controlled by the chemical metering valves on the control panel.
~~~~U~~ Pwssure Relief Procedure To reduce the risk of serious bodily injury, including fluid injection and splashing in the eyes, or on the skin, ALWAYS follow this when checking or servicing any par.
TROUBLESHOOTING CHART. ~A~~~~~ To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure Warning on page 7 before proceeding. PROBLEM Low Pressure Pump runs exiremely rough, pressure low.
PUMP SERVICE To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or ~A~~O~~ injury from moving parts, always follow the Pressure Relief Procedure Warning on page 7 before proceeding. NOTE: The following metric wrenches are needed: M6 Allen wrench, M10, and M30.
4. Inspect the plunger shaft for oil leakage from the crankcase. If leaking is obvious, replace the oil .seals (216). Otherwise, DO NOT remove these seals as they cannot be reused. NOTE: Oil Seal .Kit, part no. 801-658, is available to replace all three seals.
PARTS DRAWING Hydra-Clean 1235, P/M 800-233 (Continued) .... . .. .. . . 802-777 11.
PARTS DRAWING Hydra-Clean 1235 WIRING DIAGRAM PARTS LIST Hydra-Clean 1235, P/N 800-233 REF. PART NO. NO. 1 802-760 COVER, Switch DESCRIPTION ON. 2 801-892 CORD W/PLUG, 12/3 x 8' 1 4 801-223 SWITCH 1 1 5 801-894 SCREW, Ground 6 802-980 BOX. Switch (with plug) ' ' 1 7 801-931 GRIP.
.~ ., REF. PART ': NO. NO. 21 801-009 22 801-090 24 801-605 23 801-967 25 801-875 27 801-546 28 801-015 29 801-363 30 801:214 31 801-813 33 801-025 34 801-023 35 802-729 36 801-878 37 801-818 38 801.
PARTS DRAWING Pump, 802-629 205 I 2044 203 20; PARTS LIST Pump, 802-629 REF. NO. 201 202 t t 203 $204 $205 ,206 207 209 208 *211 210 t*212 *213 *215 *214 +** 21 6 **217 -218 ** 220 *f 219 221 222 223 PART 801-651 NO.
PARTS DRAWING Chemical Injector, 800-138 1 I1 I I I i I I PARTS LIST Chemical Injector, 800-138 REF. PART NO. NO. DESCRIPTION 1 801-684 NIPPLE, Hex, brass, 3/8 NPT QTY.
THE GRACO WARRANTY WARRANTY Gram warrants all equipment manufactured by it and bearing is name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use.
デバイスGraco Inc. 800-233の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 800-233をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 800-233の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 800-233の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 800-233で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 800-233を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 800-233の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 800-233に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 800-233デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
