Graco Inc.メーカー824-001の使用説明書/サービス説明書
ページ先へ移動 of 24
OWNER’S MANUAL 824–001 Rev D Supercedes Rev . C HYDRA-CLEAN 2000, 2800 Pressure W ashers Hydra-clean 2000 824–006 Series A 2000 psi (138 bar) Operating Pressure 2400 psi (165 bar) Maximum Wo.
824–001 T able of Contents W arnings 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation 5 . . . . . .
3 824–001 W ARNING W ARNING HAZARDOUS FLUIDS Improper handling of hazardous fluids can cause serious injury , even death, due to splashing in eyes, ingestion or bodily contamination. D Know specific hazards of fluid being used. D W ear protective eyewear , gloves, clothing, and respirator as recommended by the fluid manufac - turer .
4 824–001 Installation T ypical Installation – Pressure W asher Fig. 1 HIGH PRESSURE HOSE CONNECTION HOSE RACK INLET W A TER CONNECTION 3/4” GARDEN HOSE SPRA Y GUN SPRA Y HOSE Check for Shipping Damage Check the unit for any damage that may have occurred in shipping.
5 824–001 Operation Pressure Relief Procedure INJECTION HAZARD The system pressure must be manually relieved to prevent the system from spraying accidentally .
6 824–001 Operation 4. T rigger the gun until water sprays from the tip indicating that the air is purged from the system. 5. Open the fuel shutof f valve. Be sure the spark plug ignition cable is pushed firmly onto the spark plug. Put the switch in the “on” position and put the throttle in the “run” position.
7 824–001 Operation T rigger Safety Latch W ARNING To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, always engage the trigger safety latch whenever spraying stops, even for a moment.
8 824–001 Operation Shutdown, Flushing and Storage NOTE: An anti–freeze flush kit 802–327 is available to make flushing easier . CAUTION If water does freeze in the pressure washer , thaw it in a warm room before trying to start it. Do not pour hot water on or into the pump; it may crack the ceramic plungers! 1.
9 824–001 T roubleshooting T o reduce the risk of serious injury , including fluid injection and splashing in the eyes, or on the skin, always follow Pressure Relief Procedure on page 5 before proceeding. W ARNING Problem Cause Solution Engine will not start or is hard to start No gasoline in fuel tank or carburetor .
10 824–001 Problem Cause Solution Frequent or prema - ture failure of the packings Scored, damaged or worn plungers. Install new plungers. See PUMP SER VICE, page 13. Abrasive material in the fluid being pumped. Install proper filtration on pump inlet plumbing.
11 824–001 804–544 Pump Service W ARNING To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure W arning on page 5 before proceeding.
12 824–001 804–544 Pump Service 6. Lightly grease the retaining screw and the outer end of the plunger . Place the washer , o–ring and backup ring around the screw and install the nut through the plunger . T orque to 1 1 ft–lb (15 N m). NOTE: If you plan to replace the packings, refer to Servicing the V–Packings.
13 824–001 804–559 Pump Service W ARNING To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure W arning on page 5 before proceeding.
14 824–001 804–559 Pump Service 6. Lightly grease the retaining screw and the outer end of the plunger . Place the washer , o–ring and backup ring around the screw and install the nut through the plunger . T orque to 14.4 ft–lb (19.5 N m).
15 824–001 Accessories W ater Sandblasting Kit 800–120 For abrasive cleaning of stubborn dirt and paint. Requires a spray tip which is not included in kit (1535 uses 805–325, 2030 uses 805–313, 2540 uses 805–321, and 3040 uses 805–317).
16 824–001 Hydra-Clean 2000 Pressure W asher – Parts 04999A 1 30 31 29 32 Model 824–006, Series A 04999 18 19 20 21 22 23 25,26,27,46,57 24 34 Apply sealant to threads Supplied with .
17 824–001 Hydra-Clean 2000 Pressure W asher – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES Models 824–006, Series A Ref. No. Part No. Description Qty .
18 824–001 Hydra-Clean 2800G Pressure W asher – Parts Model 824–007, Series A 1 30 31 29 32 2 18 19 20 21 22 23 25,26,27,28,42, 24 34 1 Apply sealant to threads 2 Supplied with pump 1 33 17 16 1.
19 824–001 Hydra-Clean 2800G Pressure W asher – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES Models 824–007, Series A Ref. No. Part No. Description Qty .
20 824–001 Pump Assembly – Parts Model 804–544 1 28 58 57 49 50 55 54 56 51 05001 53 52 27 26 25 23 29 30 31 37 32 36 35 33 34 5 24 22 21 8 3 2 4 59 20 19 18 16 14 15 13 12 11 10 9 6 2 7 17 15 1.
21 824–001 Pump Assembly – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES Model 804–544 REF P ART NO. NO. DESCRIPTION QTY 1 CRANKCASE 1 2 801-484 PLUG 2 3 802-344 O-RING 1 4 PROTECT OR 1 5.
824–001 Pump Assembly – Parts Model 804–559 4 2 13 14 15 12 16 3 5 6 7 8 9 10 19 18 28 25 26 17 41 45 43 45 1 44 40 42 44 48 46 49 47 10 9 11 75 76 77 78 81 82 79 80 83 84.
23 824–001 Pump Assembly – Parts USE ONL Y GENUINE GRACO P ARTS AND ACCESSORIES MODEL 804–559 REF P ART NO. NO. DESCRIPTION QTY 1 HEAD, Pump 1 2 801-651 SCREW 8 3 801-652 W ASHER 8 4 KIT 123 O-R.
24 824–001 The SHER WIN–WILLIAMS W arranty and Disclaimers W ARRANTY Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use.
デバイスGraco Inc. 824-001の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Graco Inc. 824-001をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGraco Inc. 824-001の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Graco Inc. 824-001の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Graco Inc. 824-001で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Graco Inc. 824-001を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGraco Inc. 824-001の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Graco Inc. 824-001に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGraco Inc. 824-001デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
