GrizzlyメーカーG1023SLXの使用説明書/サービス説明書
ページ先へ移動 of 50
LEFT-TILTING 10" TABLE SAW MODEL G1023SL/G1023SLX INSTRUCTION MANUAL COPYRIGHT © FEBRUARY, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.
TABLE OF CONTENTS PAGE 1. SAFETY ........................................................................................................................................................................2 INSTRUCTIONS FOR POWER TOOLS ...................
-2- G1023SL/G1023SLX Left-Tilting 10'' Table Saw SECTION 1: SAFETY Safety Instructions For Power Tools 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate.
-4- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Additional Safety Instructions For Table Saws 1. ALWAYS use blade guard, splitter and anti-kickback fingers on all ''through-saw- ing'' operations. Through-sawing opera- tions are those when the blade cuts com- pletely through the workpiece as in ripping or crosscutting.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -5- Push Sticks The use of push sticks, particularly when cutting small or narrow workpieces, provides a double benefit for saw operators. The push stick pro- vides added leverage, enabling the operator to keep the workpiece firmly supported against the fence and the table.
-6- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Push Paddles Push paddles (shown in Figure 3 ) provide added leverage and support when ripping or crosscut- ting wide workpieces.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -7- Common Definitions, Terms and Phrases The following is a list of common definitions, terms and phrases used throughout this manual as they relate to this table saw and woodworking in general.
-8- G1023SL/G1023SLX Left-Tilting 10'' Table Saw SECTION 2: CIRCUIT REQUIREMENTS 220V Single-Phase The Model G1023SL/G1023SLX Left-Tilting 10" Table Saw has a 3 HP, 3450 RPM motor which requires a 220V single-phase circuit.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -9- We do not recommend the use of extension cords on 220V equipment. Instead, arrange the place- ment of your equipment and the installed wiring to eliminate the need for extension cords.
-10- G1023SL/G1023SLX Left-Tilting 10'' Table Saw SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G1023SL/G1023SLX Left-Tilting 10" Table Saw. The Model G1023SL/G1023SLX is part of a growing Grizzly family of fine woodworking machinery.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -11- Unpacking The Model G1023SL/G1023SLX base unit is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you have signed for delivery, immediately call our Customer Service for advice.
-12- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Piece Inventory After all the parts have been removed from their containers, you should have: • Table Saw Unit ( Figure 6 ) • Miter Gaug.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -13- Clean up The table and other unpainted parts of the Model G1023SL/G1023SLX are coated with a waxy grease that protects them from corrosion during shipment. Clean this grease off with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser.
-14- G1023SL/G1023SLX Left-Tilting 10'' Table Saw SECTION 4: ASSEMBLY Most of your Model G1023SL/G1023SLX has been assembled at the factory, but some parts must be assembled or installed after delivery. We have organized the assembly process into steps.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -15- Figure 9. Using tape to shim for wing alignment. Figure 10. Installing switch. Masking Tape 8. Now, check the alignment of the table and both wings with a straightedge. The straight- edge should run flat across both wings and the table top.
-16- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Guard Bracket Figure 12. Attaching guard support shaft. Figure 13. Splitter bracket installed. Figure 11. Motor Brace. To install the guard support shaft: 1. Place the threaded end of the shaft through the hole in the back of the saw ( Figure 12 ).
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -17- Table Insert Handwheel The table insert provides access to the blade and the arbor when removed.
-18- G1023SL/G1023SLX Left-Tilting 10'' Table Saw 2. Set a machinist’s square against the face of the blade splitter. Slightly rotate the rear bracket to adjust the face of the blade splitter perpendicular to the table top as shown in Figure 18.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -19- 4. If the blade splitter is to the right of the blade as shown in Figure 20 , simply add washers between the splitter and the front mounting bracket, and adjust the rear splitter support as shown in Figure 21 .
-20- G1023SL/G1023SLX Left-Tilting 10'' Table Saw 9. Moving the arbor bracket moves the V-belts and pulleys out of alignment, so adjustment of the motor pulley is required. Simply loosen the setscrew in the middle groove of the pul- ley, and slowly slide the pulley toward the end of the motor shaft.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -21- SECTION 5: ADJUSTMENTS Blade Height Blade Tilt 1. Set your blade angle at zero as shown on the angle indicator on the front of the saw and raise the blade several inches above the table. 2. Place a machinist’s square flat on the table and slide it alongside the blade.
-22- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Figure 25. Table mounting bolt holes. Table Mounting Locations 6. If the blade tip does not touch the end of the adjustable square similar to the first mea- surement, then the table will need to be adjusted.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -23- Figure 26. Shim procedure diagram A. Figure 27. Shim procedure diagram B. 11. Refer to Figures 26 and 27, for shim place- ment. If the distance of A is shorter than B, shim(s) will need to be placed under corners #1 and #2.
-24- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Blade Alignment The blade position can be adjusted slightly in case it contacts the table insert when raised or tilted. This adjustment can be made either by moving the whole trunnion assembly, or by just moving the arbor bracket.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -25- 5. Moving the arbor bracket moves the V-belts and pulleys out of alignment, so adjustment of the motor pulley is required. Simply loosen the setscrew in the middle motor groove pul- ley and slowly slide the pulley towards the end of the motor shaft.
-26- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Pre-Run Check SECTION 6: OPERATIONS Before you begin to use your Model G1023SL/G1023SLX Left-Tilting 10" Table Saw, you should give it a thorough inspection. While making your inspection, ask yourself the follow- ing questions: 1.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -27- Blade Selection Choosing the correct blade for the job is essential for the safe and efficient use of your table saw. Ignoring this important step could result in dam- age to the saw and serious injury to the operator.
-28- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Figure 35. Plywood blade. 4. Plywood Blade: Used for cutting plywood or veneers. A 10" plywood blade will have 40- 80 teeth, a steep alternate top bevel tooth profile and very shallow gullet.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -29- Figure 36. Cross-cut operation. Crosscutting Crosscutting means cutting across the grain of the wood. In wood products without grain (i.e. MDF, particleboard) crosscutting simply means cutting across the width of the stock.
-30- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Ripping Ripping means to cut with the grain of the wood. In other materials such as MDF or plywood, rip- ping simply means to cut lengthwise. To rip a board: 1. Inspect the board for soundness.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -31- Always use push sticks, featherboards, push paddles and other safety accessories whenever possible to increase safety and control during operations which require the blade guard and splitter to be removed from the saw.
-32- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Always use push sticks, featherboards, push paddles and other safety accessories whenever possible to increase safety and control during operations which require that the blade guard and splitter must be removed from the saw.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -33- Instructions on using moulding heads have been intentionally left out. They are very dangerous when not used properly. Considerable skill and training beyond the scope of this manual are required to safely operate a moulding head.
-34- G1023SL/G1023SLX Left-Tilting 10'' Table Saw SECTION 7: MAINTENANCE V-Belt To ensure optimum power transmission from the motor to the blade, the V-belts must be in good condition and operate under the proper tension. When replacing V-belts, replace all three at the same time —even if they do not all appear worn.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -35- Lubricate the areas indicated below every 12 months. 1. Blade angling trunnions . These should be lubricated with 6 or 7 drops of light machine oil. 2. Blade height trunnion . This should also be lubricated with 6 or 7 drops of light machine oil.
-36- G1023SL/G1023SLX Left-Tilting 10'' Table Saw SINGLE-PHASE 220V POWER SOURCE MOTOR A B AMP RESET 96 98 1/2 T1/2 T3/6 8 3/4 T2/4 L1/1 L3/5 7 L2/3 5/6 95 18 22 26 OFF 3 HP Magnetic Switch .
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -37- The following pages contain general machine data, troubleshooting guide, parts diagram, parts list and Warranty/Return information for your Model G1023SL/G1023SLX Left-Tilting 10" Table Saw.
-38- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET GRIZZL Y MODEL G1023SL/G1023SLX LEFT -TIL TING 10" T ABLE SA W Overall Dimensions: Table Size .
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -39-.
-40- G1023SL/G1023SLX Left-Tilting 10'' Table Saw.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -41-.
-42- G1023SL/G1023SLX Left-Tilting 10'' Table Saw 01 P1023SL001 CABINET 01A P1023SL001A LOWER PANEL 02 P1023SL002 SCALE 03 PHTEK4 TAP SCREW 10-24 X 10L 04 P1023SL004 MOTOR COVER 05 P1023SL00.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -43- 99 PB32 HEX BOLT 5 ⁄ 16 "-18 X 5 ⁄ 8 " 104 P1023SL104 FLAT WASHER 3 ⁄ 16 " 106 PW02 FLAT WASHER 3 ⁄ 8 " 140 PB11.
-44- G1023SL/G1023SLX Left-Tilting 10'' Table Saw SYMPTOM Motor will not start. Motor will not start; fuses or circuit breakers blow. Motor overheats. Motor stalls (resulting in blown fuses or tripped cir- cuit). Machine slows when oper- ating.
G1023SL/G1023SLX Left-Tilting 10'' Table Saw -45-.
-46- G1023SL/G1023SLX Left-Tilting 10'' Table Saw Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
CUT ALONG DOTTED LINE 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8&qu.
Place Stamp Here FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
デバイスGrizzly G1023SLXの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Grizzly G1023SLXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly G1023SLXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly G1023SLXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly G1023SLXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly G1023SLXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly G1023SLXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly G1023SLXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly G1023SLXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。