GrizzlyメーカーG1258の使用説明書/サービス説明書
ページ先へ移動 of 26
20" BANDSAW MODEL G1258 INSTRUCTION MANUAL COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
.
G1258 20" Bandsaw -1- Table Of Contents PAGE 1. SAFETY ....................................................................................................................2 SAFETY SYMBOLS ..........................................................
-2- G1258 20" Bandsaw Safety Instructions For Power Tools SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment Failure to obey a DANGER symbol and notation WILL result in serious personal injury including loss of life or body parts.
G1258 20" Bandsaw -3- Safety Instructions For Power Tools 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories. 15. DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and the like.
-4- G1258 20" Bandsaw Additional Safety Instructions For Bandsaws No list of safety guidelines can be com- plete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect.
G1258 20" Bandsaw -5- 220V Operation SECTION 2: CIRCUIT REQUIREMENTS Your Model G1258 Bandsaw is supplied with a single phase 220V only motor. Under normal use, the motor draws approximately 15 amps @ 220V. We recommend a 20 amp circuit breaker or slow- blow fuse.
To operate this or any power tool safely and efficiently, it is essential to become as familiar with it as possible. The time you invest before you begin to use your Model G1258 will be time well spent. DO NOT operate this machine until you are com- pletely familiar with the contents of this manual.
G1258 20" Bandsaw -7- Unpacking The bandsaw is shipped from the factory in a carefully packed carton. If you find the machine to be damaged after you’ve signed for delivery and the truck and driver are already gone, you will need to file a freight claim with the carrier.
-8- G1258 20" Bandsaw Clean Up The unpainted surfaces are coated with a waxy oil to protect it from corrosion during shipment. Remove the protective coating with common paint thinner (mineral spirits) and paper towels. Do not use gasoline or other petroleum based solvents because of their extremely low flash points.
G1258 20" Bandsaw -9- SECTION 4: ASSEMBLY Fence Most of your G1258 20'' bandsaw has been assembled at the factory. Only the fence assem- bly requires installation. To mount the fence to the bandsaw table: 1. Mount the front rail to the table using the 2 5 ⁄ 16 -18 x 2 1 ⁄ 2 '' Cap Screws and the 2 Spacers provided.
-10- G1258 20" Bandsaw SECTION 5: ADJUSTMENTS Tracking To adjust the tracking: 1. Disconnect the bandsaw from the power source and open the top and bottom wheel covers. Adjust the upper and lower guide assemblies away from the blade. 2. Loosen the lock nut on the tracking knob.
G1258 20" Bandsaw -11- Normally Steps 1-4 are implemented prior to installing a new blade. To adjust the upper guides: 1. Loosen the bearing guide shaft lock nuts. 2. The bearing guides are mounted on an eccentric shaft. With a regular screwdriver, rotate the guides away from the blade.
-12- G1258 20" Bandsaw 7. Now rotate the bearing guide shafts until the bearings are approximately 1 ⁄ 64 '' from the blade. Hold the shafts in place with a screw driver and tighten the bearing guide lock nuts. The guide bearing, when adjusted cor- rectly, should have a slight drag against the blade.
G1258 20" Bandsaw -13- After changing a blade, the upper and lower blade support bearings and guide blocks must be readjusted. Always adjust the guide assemblies away from the blade before installing a new blade or making blade adjustments. To change blades: 1.
-14- G1258 20" Bandsaw SECTION 6: OPERATIONS Overview Test Run The bandsaw is one of the most versatile wood cutting tools in the shop. It is capable of perform- ing many different cutting functions including, but not limited to: STRAIGHT CUTS 1.
G1258 20" Bandsaw -15- A bandsaw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from a bandsaw blade if you give it fair treatment. Be sure you use blades with proper width and temper for the various types of cutting operations.
-16- G1258 20" Bandsaw 5. Draw a reference line on the edge of the board. 6. Support ends of the board if necessary. 7. Feed work slowly and evenly. Cutting Curves When cutting curves, simultaneously feed and turn the stock carefully so that the blade follows the layout line without being twisted.
G1258 20" Bandsaw -17- SECTION 7: MAINTENANCE Shielded and pre-lubricated ball bearings require no lubrication for the life of the bearings. All bear- ings are standard sizes and replacements can be purchased from our parts department or your local bearing supply store.
-18- G1258 20" Bandsaw The following pages contain general machine data, parts diagrams/lists, and Warranty/Return information for your Model G1258 20" Bandsaw. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department.
G1258 20" Bandsaw -19- Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G1258 20" BANDSAW MACHINE DATA SHEET Design Type: ...........................................................
PARTS DIAGRAM AND PARTS LIST.
G1258 20" Bandsaw -21- REF PART # DESCRIPTION REF PART # DESCRIPTION 01 P1258001 BODY 02 P1258002 BEARING BASE 03 P6305 BEARING 6305-2RS 04 P1258004 SHAFT 05 PK28M KEY 7 X 7 X 29 06 PN03 HEX NUT .
-22- G1258 20" Bandsaw Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
CUT ALONG DOTTED LINE 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8".
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
デバイスGrizzly G1258の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Grizzly G1258をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly G1258の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly G1258の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly G1258で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly G1258を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly G1258の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly G1258に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly G1258デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。