GrizzlyメーカーH3390の使用説明書/サービス説明書
ページ先へ移動 of 32
10" WET TILE SAW MODEL H3390 INSTRUCTION MANUAL COPYRIGHT © NOVEMBER 2002 BY GRIZZLY INDUSTRIAL, INC WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.
TABLE OF CONTENTS PAGE 1. SAFETY ....................................................................................................................... ...............................2 SAFETY RULES FOR TOOLS ..........................................
-2- H3390 Wet Tile Saw SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
H3390 Wet Tile Saw -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size must be in accor- dance with the chart below. The amperage rating is listed on the motor or tool name- plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
-4- H3390 Wet Tile Saw 1. Water Pump . Replace the water pump with a replacement pump from our parts department only. 2. Wet Hands. DO NOT touch connections with wet hands. 3. Plug In. All plug and receptacles should be off the ground and in a dry location.
H3390 Wet Tile Saw -5- SECTION 2: INTRODUCTION We are proud to offer the Grizzly Model H3390 Wet Tile Saw. The Model H3390 is part of a growing Grizzly family of fine woodworking machinery.
-6- H3390 Wet Tile Saw SECTION 3: CIRCUIT REQUIREMENTS 110V Operation The Model H3390 is wired to operate at 110V. A Ground Fault Circuit Interrupter (GFCI) must be used at all times when using this saw. If an outlet is not available that is equipped with a GFCI, use a GFCI plug adapter between the saw power cord and a properly grounded outlet.
H3390 Wet Tile Saw -7- Grounding Extension Cord Reduce the risk of elec- trocution by keeping all connections dry and off the ground. DO NOT touch plugs with wet hands. Failure to follow these warning could result in serious injury. NOTICE The wire on the power cord with green or green and yellow striped insulation is the grounding conductor.
-8- H3390 Wet Tile Saw Clean Up Site Considerations Unsupervised children and visitors entering a shop could receive seri- ous personal injury. Ensure child and visitor safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time.
H3390 Wet Tile Saw -9- Main Features C B D A H E F N I J K L M G O Figure 2. Right side of saw. Figure 3. Left side of saw. A. Saw Frame B. Water Reservoir C. Saw Stand D. Water Pump E. Motor F. Blade Guard G. Power Switch H. Water Pump Plug-In I. V-Belt Cover J.
-10- H3390 Wet Tile Saw Assembly Keep clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses dur- ing the entire assembly process. Failure to com- ply may result in serious personal injury. Disconnect power to the machine when perform- ing any maintenance or assembly.
H3390 Wet Tile Saw -11- 4. Slide the plastic water reservoir into one end of the saw frame as shown in Figure 7 . Be sure the reservoir is not protruding from either end of the frame. Figure 7. Installing the water reservoir. 8. Mount the motor assembly to the frame using (2) M10-1.
-12- H3390 Wet Tile Saw 9. Attach the blade guard to the motor assem- bly using the M8-1.25 x 30 lock knob and M8 flat washer as shown in Figure 11 . Tile saw blades are sold separately. 10. Place the water pump inside the water reser- voir and plug the pump cord into the recepta- cle on the side of the motor assembly.
H3390 Wet Tile Saw -13- 12. Slide the plastic rail end pieces over each of the table rail ends as shown in Figure 15 . 13. Attach the rail/table assembly to the saw frame, using (2) M14-2.0 x 35 hex bolts, (2) M14 flat washers, and (2) M14 external tooth washers as shown in Figure 16 .
-14- H3390 Wet Tile Saw Before starting the machine: 1. Read this manual and make sure you follow all safety precautions before operating this machine. 2. Make sure the blade guard has been cor- rectly installed and is adjusted properly as shown on Page 12 .
H3390 Wet Tile Saw -15- Lubrication To prevent excessive wear on the saw blade, be sure to maintain a continuous flow of water on both sides of the blade. Never cut tile without the water lubrication system running. To set up the water lube system: 1.
-16- H3390 Wet Tile Saw Cut Preparation To prepare for a cut: 1. Fill the water reservoir with water. 2. Plug the saw into the power source. Be sure the cord is positioned with the “drip loop” below the level of the outlet as shown in Figure 18, Page 14 .
H3390 Wet Tile Saw -17- Rip Fence When multiple tiles need to be cut to the same dimension, the rip fence can increase production. Use the scale on the table to set the rip fence to the desired cut.
-18- H3390 Wet Tile Saw SECTION 6: MAINTENANCE General Regular periodic maintenance on your Model H3390 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: 1.
H3390 Wet Tile Saw -19- SECTION 7: REFERENCE INFO If you need parts or help in assembling your machine, or if you need operational information, call the Grizzly Service Department.
-20- H3390 Wet Tile Saw Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type .....................................................................................................
H3390 Wet Tile Saw -21- 48 6 5 4 3 2 1 51 10 8 7 12 9 36 16 11 9 17 37 13 14 15 33 18 19 22 55 54 53 47 44 46 52 45 28 31 32 30 29 26 27 25 56 39 40 38 43 41 42 18 45 48 49 50 24 57 23 58 23 34 35 20 .
-22- H3390 Wet Tile Saw 61 70 65 66 68 67 64 63 62 60 69.
H3390 Wet Tile Saw -23- 36 PH3390036 WHEEL COVER 37 PSB14M CAP SCREW M8-1.25 X 20 38 PH3390038 V-BELT A-680 39 PSB14M CAP SCREW M8-1.25 X 20 40 PH3390040 PULLEY COVER 41 PH3390041 DRIVE PULLEY 42 PK12.
-24- H3390 Wet Tile Saw NOTES.
H3390 Wet Tile Saw -25- NOTES.
-26- H3390 Wet Tile Saw Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
CUT ALONG DOTTED LINE 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8&qu.
Place Stamp Here FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
.
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website T oday And .
デバイスGrizzly H3390の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Grizzly H3390をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly H3390の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly H3390の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly H3390で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly H3390を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly H3390の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly H3390に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly H3390デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
