GrizzlyメーカーH6144の使用説明書/サービス説明書
ページ先へ移動 of 20
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
H6144 34° Angle Finish Nailer–2½" -2 - -2 - 6. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PER- SONNEL TO OPERATE MACHIN- ERY. Make sure operation instruc- tions are safe and clearly under- stood. 7. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visi- tors a safe distance from the work area.
H6144 34° Angle Finish Nailer–2½" -3 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source .
H6144 34° Angle Finish Nailer–2½" -4 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment.
H6144 34° Angle Finish Nailer–2½" -5 - INTRODUCTION If you have any c omm ents r egar ding t his man ual, pl ease write t o us at th e foll owing add ress : Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpo rt ant ly , we s tan d b ehin d ou r too ls.
H6144 34° Angle Finish Nailer–2½" -6 - SET UP Figure 1. Model H6144 inventory. B C D G Unpacki ng Y our M od el H 61 4 4 l eft our w areho use in a ca reful ly pac ked b ox.
H6144 34° Angle Finish Nailer–2½" -7 - -7 - Compressed Air Sy stem The M ode l H 61 44 is de sig ned to be op er- ated at 6 0 - 1 0 0 PSI us ing cle an, d ry, reg u- late d, c omp ress ed air . DO N OT exc ee d th e max imum o pe rati ng pr ess ure fo r your mod el .
H6144 34° Angle Finish Nailer–2½" -8 - Safety Y oke A safe ty yo ke mec han ism o n the nos e of t he nai ler ac ts a s a se con dar y saf ety devi ce. Whe n t he tri gge r i s pr ess ed, th e nai ler wi ll no t fire unt il t he s afety yoke mec han ism is dep ress ed.
H6144 34° Angle Finish Nailer–2½" -9 - OPERATIONS Loadin g When replacing nails in your Model H6144, follow these guidelines: Gauge: 15 Length: 1 1 ⁄ 4 " -2 1 ⁄ 2 " Capacity: 40 Angle: 34 ° NOT IC E : A n umb er o f m anufa ctur ers' nai ls m ay fit th e M ode l H 61 4 4.
H6144 34° Angle Finish Nailer–2½" -10 - Figure 5. Depth adjustment knob. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. 5. Pull the trigger. If the nail drove into the wood far enough, continue with your intended operations.
H6144 34° Angle Finish Nailer–2½" -11 - The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. T o cl ea r a j amm ed n ail f rom th e dis - cha rg e ar ea on th e M ode l H 6144 : 1.
H6144 34° Angle Finish Nailer–2½" -12 - Replacin g Pist ons / O - Rin gs If yo u us e your na iler day in and day out , rep air pisto ns are c hea p ins uran ce agai nst wa sted d own tim e and lo st prof its, in the event that a p isto n or pi ston sh aft bec ome s wo rn out.
H6144 34° Angle Finish Nailer–2½" -13 - CLEANING & LUBRICATION Cleanin g Use a go od s olven t to c lean the no se ass emb ly of t he n aile r . Always b e sure th at t he n ail er i s dr y b efor e us in g it agai n. Do not a llow du st, c hips , s and, et c.
H6144 34° Angle Finish Nailer–2½" -14 - H6144 PARTS BREAKDOWN .
H6144 34° Angle Finish Nailer–2½" -15 - H6144 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6144001 SPECIAL CAP SCREW M5-.8 X 12 45 PH6144045 STEEL BALL 2MM 2 PH6144002 AIR DEFLECTOR 46 PH6144046 SAFETY SEAT 3 PH6144003 RUBBER WASHER 10 MM 47 PH6144047 DRIVE PIN 4 PSB38M CAP SCREW M5-.
H6144 34° Angle Finish Nailer–2½" -16 - 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting & use teflon tape. 1. Replace damaged seals. 1. Tighten screws and fit - tings.
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Name _________________________________________________________________________ Street ________________________________________________________________________ City____________________State________Zip_.
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street______________________________.
デバイスGrizzly H6144の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Grizzly H6144をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly H6144の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly H6144の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly H6144で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly H6144を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly H6144の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly H6144に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly H6144デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。